CAPITAL STOVES HOLSWORTHY 5 ECO User manual

INSTALLATION AND OPERATING
INSTRUCTIONS
APPROVED - CONFORMING TO
EN13240:2001 AND EN 13240-A2:2004
REDUCING CARBON EMISSIONS IN THE UK
APPLICABLE TO THE FOLLOWING STOVES MODELS:
HOLSWORTHY 5 ECO
STOVES MUST BE FITTED BY APPROVED, QUALIFIED
AND COMPETENT INSTALLERS
PLEASE LEAVE THIS BOOKLET WITH THE HOUSEHOLDER
Stoves operate at very high temperatures. All persons
including children and the inrm should be warned of this and
not allowed to touch any surfaces whilst in use. The operator
must use the glove provided.
HOLSWORTHY 5 ECO STOVE INSTRUCTIONS - REV. 1 - AUG 2023

2
CONTENTS
STOVE DIMENSIONS, OUTPUT & EFFICIENCY ............................................
INSTALLATION AND COMMISSIONING .....................................................
THE CLEAN AIR ACT AND SMOKE CONTROL AREAS ...............................
INSTALLATION SAFETY ..................................................................................
CHIMNEY AND FLUE REQUIREMENTS .........................................................
HEARTH AND CLEARANCE .........................................................................
VENTILATION REQUIREMENTS .....................................................................
FITTING .........................................................................................................
OPERATION .................................................................................................
GENERAL MAINTENANCE ..........................................................................
SAFETY NOTES & TROUBLESHOOTING .......................................................
SPARES .........................................................................................................
STOVE ACCESSORIES ..................................................................................
RECYCLING AND DISPOSAL .......................................................................
WARRANTY ..................................................................................................
3
4
5
6
7
8
9
10
12
14
15
17
18
18
19
3
STOVE DIMENSIONS, OUTPUT AND EFFICIENCY
WOOD 5kW
EFFICIENCY
ENERGY CLASS
77.7%
A
FLUE GAS TEMPERATURE 270 °C
NOX mg/m3 @ 13% O2
NOMINAL OUTPUT 4.9kW
OUTPUT RANGE* 3.0-8.0kW
HOLSWORTHY 5 ECO
*See page 10 for ventilation requirements
425.00
1042.00
1074.00
127.00
127.00
133.00
470.00
484.00
235.00 470.00
506.00
933.00
100.00
MINIMUM CLEARANCE TO COMBUSTIBLES REAR - 50mm
SIDE - 250mm
OCG mg/m3 @ 13% O2 81
CO mg/m3 @ 13% O2
PARTICULATE EMMISSIONS mg/m3 @ 13% O2
1186
40
116
ENERGY INDEX
SEASONAL EFFICIENCY
103
67.7

INSTALLATION AND COMMISSIONING
This stove must be installed and commissioned by a fully qualied registered engineer,or
the building inspector must be informed. For more details contact your local authority.
This document, when completed by the installer, constitutes part of a ‘Hearth Notice’ for
purposes of Building Law. It must be left with the house holder and placed where it can
easily be found.
Serial Number: .................................................................................................................................
Installed at Location: .......................................................................................................................
By: .....................................................................................................................................................
I denitively assert that this installation is safe, has been lit and demonstrated to the
householder, conforms with current building regulations and with these instructions.
Signed: ..............................................................................................................................................
Date: ................................................................................................................................................
Flue draught measured on commissioning: .................................................................................
Fuel used on commissioning: .........................................................................................................
4
THE CLEAN AIR ACT 1993 AND SMOKE CONTROL AREAS
Under the Clean Air Act local authorities may declare the whole or part of the district
of the authority to be a smoke control area. It is an offence to emit smoke from a
chimney of a building, from a furnace or from any xed boiler if located in a
designated smoke control area. It is also an offence to acquire an “unauthorised
fuel”for use within a smoke control area unless it is used in an “exempt” appliance
(“exempted” from the controls which generally apply in the smoke control area).In
England appliances are exempted by publication on a list by the Secretary of State in
accordance with changes made to sections 20 and 21of the Clean Air Act 1993 by
section 15 of the Deregulation Act 2015. Similarly in Scotland appliances are exempted
by publication on a list by Scottish Ministers under section 50 of the Regulatory Reform
(Scotland) Act 2014. In Northern Ireland appliances are exempted by publication on a
list by the Department of Agriculture, Environment and Rural Affairs under Section 16 of
the Environmental Better regulation Act (Northern Ireland) 2016. In Wales appliances
are exempted by regulations made by Welsh Ministers.
Further information on the requirements of the Clean Air Act can be found here:
https://www.gov.uk/smoke-control-area-rules
Your local authority is responsible for implementing the Clean Air Act 1993 including
designation and supervision of smoke control areas and you can contact them for
details of Clean Air Act requirements.
The Holsworthy 5 Eco has been recommended as suitable for use in smoke control areas
when burning wood logs. The Holsworthy 5 Eco has been tted with a permanent stop to
prevent closure of the air control beyond 10mm open.
Refuelling onto a low re bed can cause excessive smoke - If the re bed is not sufcient
to light a new fuel charge, excessive smoke emission can occur. Refuelling must be
carried out onto a bed of glowing embers and ash such that the new fuel ignites in a
reasonable period. If there are too few embers in the re bed, add kindling to prevent
excessive smoke.
Fuel overloading can cause excessive smoke - The maximum amount of fuel specied in
this manual should not be exceeded, overloading can cause excess smoke.
5

CHIMNEY AND FLUE REQUIREMENTS
Check the chimney is in good condition, dry, free from cracks, leaks and obstructions. The
diameter of the ue should not be less than 150mm and not more than 230mm. If any of
these requirements are not met, the chimney should be lined by a suitable method.
It is recommended to use a 125mm liner for best performance, however a 150mm ue
liner may be used if necessary, in accordance with the Building Regulations. The chimney
and connecting ue pipe should not narrow to less than the size of the outlet socket
(collar) of the stove at any point.
To achieve the minimum clearance distances, an insulated ue must be used.
This stove must not share a chimney with any other appliance.
A ue draught of minimum 12 Pascals is required for satisfactory appliance performance.
The ue draught should be checked under re at high output and if it exceeds 25Pa, a
draught stabiliser may be required so that the rate of burning can be controlled, and to
prevent possible over-ring.
The chimney height and the position of the chimney terminal must conform to Building
Regulations and the latest edition of BS EN 15287-1, Design, Installation and
Commissioning of Chimneys should be followed.
The chimney must be swept before connection to the stove and swept at least every
twelve months thereafter. It is recommended that your chimney is swept every six months.
Where a chimney is believed to have previously served an open re installation it is
possible that the higher ue gas temperature from a closed appliance may loosen
deposits that were previously rmly adhered, with the consequent risk of ue blockage. It
is therefore recommended that the chimney be swept a second time within a month of
regular use after installation.
If you have any doubts about the suitability of your chimney, consult your local
dealer/stockist. They will also be able to provide advice about the possible need for a
specialist cowl.
It is essential that only recommended fuels are used - see page 13 for more information.
Building regulations require that whenever a new or replacement xed solid fuel or
wood/biomass appliance is installed in a dwelling a carbon monoxide alarm must be
tted in the same room as the appliance. Further guidance on the installation of the
carbon monoxide alarm is available in BS EN 50292:2002 and from the alarm
manufacturer’s instructions. Provision of an alarm must not be considered a substitute
for either installing the appliance correctly or ensuring regular servicing and
maintenance of the appliance and chimney system.
7
INSTALLATION SAFETY
IMPORTANT: THE INSTALLATION OF THIS APPLIANCE MUST COMPLY WITH BS8303 - CODE OF
PRACTICE FOR INSTALLATION OF DOMESTIC HEATING AND COOKING APPLIANCES
BURNING SOLID MINERAL FUEL, NATIONAL BUILDING REGULATIONS, LOCAL BY-LAWS AND
STANDARDS AND THE REQUIREMENTS OF THE HEALTH AND SAFETY AT WORK ACT 1974.
Installing a stove is a ‘controlled service’, the law expects that it is either supervised by a
qualied installer or that the building inspector is informed. Check with your local
authority.
Health and Safety Precautions: Special care must be taken when installing the stove such
that the requirements of the Health and Safety at Work Act are met.
Handling: Adequate facilities must be available for loading, unloading and site handling.
Fire Cement: Some types of re cement are caustic and should not be allowed to come
into contact with the skin. In case of contact wash immediately with plenty of water.
Asbestos: This stove contains no asbestos. If there is a possibility of disturbing any asbestos
in the course of installation then please seek specialist guidance and use appropriate
protective equipment.
Metal Parts: When installing or servicing this stove care should be taken to avoid the
possibility of personal injury.
Weight: Your stove is heavy – take great care when moving it and ensure that the
intended replace can support the weight – consider tting a load distributing plate.
Fireguard Safety: A reguard must be used in the presence of children, and old and/or
inrm people. The reguard should be manufactured in accordance with BS 8423:2002,
Fireguards for use with solid fuel appliances.
Ventilation: Additional ventilation may be required in your room. Avoid installing an
extractor fan in the same room as your stove, If you need an extractor fan, consult a
specialist and have the installation tested for safety.`
UNLESS THE INSTALLER IS QUALIFIED TO APPROVE INSTALLATION THEN APPROVAL MUST BE
SOUGHT FROM YOUR LOCAL BUILDING CONTROL DEPARTMENT. THE SUPPLIER ACCEPTS NO
RESPONSIBILITY IF THIS ADVICE IS NOT FOLLOWED.
6

VENTILATION REQUIREMENTS
VENTILATION INTO A ROOM FOR COMBUSTION AIR IS AN ESSENTIAL REQUIREMENT.
Flues Without a Flue Draft Stabiliser
2.5kW - 5kW Output - When installing without a ue draft stabiliser into houses built before
2008, no additional permanent ventilation will be required.* Houses built after this date
will require additional means of permanent ventilation direct to outside of at least 4400
mm².
*Note: Installers must verify adequate draw and install ventilation if required. See
Appendix F of Building Regulations Approved Document J.
5kW-8kW Output - If you are intending to burn the stove above the independently tested
5kW output, then a permanently open air vent into the room where the stove is situated
will be required. For house built before 2008, the vent must have a free area of at least
1650mm². For house built after 2008, the vent must have a free area of at least 4400mm².
Flues With a Flue Draft Stabiliser
2.5kW-5kW Output - When installing with a ue draft stabiliser into houses built before
2008, at least 1500mm² additional means of permanent ventilation direct to outside is
required. Houses built after this date will require additional means of permanent
ventilation direct to outside of at least 6800 mm².
5kW-8kW Output - If you are intending to burn the stove above the independently tested
5kW output, then a permanently open air vent into the room where the stove is situated
will be required. For house built before 2008, the vent must have a free area of at least
4050mm². For house built after 2008, the vent must have a free area of at least 6800mm².
9
Clearance to
Side Wall:
Minimum 250mm
Clearance to
Side Wall:
Minimum 250mm Clearance to
Front
Combustibles:
Minimum
550mm
For freestanding stove:
Minimum 840mm x 840mm
x12mm Non-Combustible Hearth
Clearance to
Back Wall:
Minimum 50mm
HEARTH AND CLEARANCE
The hearth must extend at least 225mm at the front of the stove and 150mm on either
side. Care should be taken to level the stove and secure the hearth. If existing oors do
not have adequate load bearing capacity then suitable modications must be adopted.
When the stove is in the desired position, level the stove using the adjustable feet, then
mark the hearth through the holes, remove the stove, and drill and plug the hearth for
securing the stove.
Clearance Distance to Combustibles:
If the stove is to be installed adjacent to materials that can catch re like wood then the
following clearances must be adhered to:
It is possible to t the stove with less clearance around it – down to 50mm, but the non-
combustible material around it must be at least 150mm thick. Take care that the wall
nish is suitable to withstand temperatures of up to 200ºC.
A Light Duty Hearth can be used with the Holsworthy 5 ECO as long as it is installed in
accordance with Building Regulations and the minimum clearance distances above.
8

11
FITTING - CONTINUED
Place the stove on a non- combustible hearth conforming to building regulations, noting
the distances to combustible materials given on page 8.
Fix the stove securely to the hearth by drilling through the xing holes inside the log store,
into the hearth, with a 6mm masonry drill. Screw down with the bolts and washers
provided.
Outside Air Kit
This stove can be tted with an outside air kit that will draw air in from an external wall. An
outside air kit should be tted when adequate ventilation can not be provided or an
extractor is tted in the same room.
See Ventilation Requirements on page 9.
Check the Installation:
Once installed, light the re, demonstrate it to the householder and check that:
1. It burns controllably and does not emit fumes to the room.
2. The route for gases from the stove to the chimney terminal is completely airtight,
unobstructed and able to be swept.
3. The entire construction is of durable reproof materials.
4. The ue presents a draught in use of at least 12Pa and not in excess of 25 Pa.
5. Ensure that a carbon monoxide alarm is tted in the same room as the appliance.
Further guidance on the installation of the carbon monoxide alarm is available in BS EN
50292:2002 and from the alarm manufacturer’s instructions. Provision of an alarm must
not be considered a substitute for either installing the appliance correctly or ensuring
regular servicing and maintenance of the appliance and chimney system.
Keep Children Safe - Always use a reguard to BS 8423:2002 (Replaces BS 6539) in the
presence of children, aged and/or inrm persons.
FITTING
An existing replace opening can be modied to accommodate the stove. Always
consult your stove supplier for a detailed survey of your particular circumstances.
Upon completion of installation, the appliance must be checked under re for soundness
of joints and seals, and that all smoke and fumes are taken from the appliance, up the
chimney and emitted safely
Initial Assembly:
To make it easier to handle the stove on installation, the bafe plates, and bricks can be
removed. Place in a secure place to avoid damage. Ret after installation.
Top or Rear Flue
Remove the ue collar and accessory pack from inside the stove cavity. The ue collar
must be tted to the top or rear of the stove, depending on installation. Fasten the ue
outlet and blanking plate to the top or back ue outlet opening, on a thin bead of re
cement. Do not over tighten.
The stove will arrive with the blanking plate tted to the rear. The blanking plate can be
removed, allowing the collar to be tted for rear ue installations. The circular cut out in
the rear panel and heat shield must be knocked out to enable this style of connection.
Ret the blacking plate in the top ue position.
For rear ue connection, remove the rear panel from the stove, unscrew the two screws
at the back of the stove, in the top of the log store. Remove the top plate and unscrew
the two screws on top. The rear panel can then slide off. Unscrew the two screws to
remove the heat shield panel. Knock/cut out the circular cutouts for rear ue installation,
then replace the rear heat shield and rear panel. Remember to ret the blanking plate to
the unused ue position if it has been removed.
Your stove can be sealed to the chimney using a short (up to about 500mm) length of
uninsulated pipe in several ways, four of which are shown below, but distances to
combustibles must be taken in to account as described in Building Regulations.
10

OPERATION
Primary Air - Slide Control - Slide
right to open and left to close.
Open this when you start a re,
and to regulate the stove burn.
The more the stove primary air
slide is open the more air is being
introduced to the stove. Whilst this
is useful to start a re it should be
closed signicantly for the best
efciency.
Tertiary Air - A tertiary air supply is
bled into the stove from the rear
panel. Its function is to ignite
unburned gasses assisting with a
clean burn. It is advisable to clear
these holes from time to time with
a brush, especially when the stove
is being serviced or after long
periods of burning. ONLY CARRY
OUT THIS AND ALL SERVICING
PROCEDURES WHEN THE STOVE IS
COLD. This tertiary air supply is
permanently open and allows a
small amount of air into the stove.
Operation with air controls open
can cause excess smoke. These
stoves must not be operated with
air controls left open except as
directed in these instructions.
12
TERTIARY AIR
BAR
PRIMARY AIR
CONTROL
OPERATION - CONTINUED
It is widely recognised that the “Upside Down” or “Top-Down” method of lighting a re
from the top down in a closed appliance is a more efcient way of warming up the ue
and results in far less particulates on start-up. Therefore, you should place relighters on
top of the kindling before lighting. Allow the fuel to reach a steady glow, building up the
re gradually. Once you have a good re established across the re bed, further fuel can
be added as required.
When your re is well established you can start to restrict the primary air intake, the
primary air control can be fully closed.
Operation with the air controls or appliance dampers open can cause excess smoke.
The appliance must not be operated with air controls, appliance dampers or door left
open except as directed in the instructions.
Do not stack logs above the tertiary air bar in the back of the stove as this will inhibit
combustion and result in a less efcient burn.
Recommended Fuels - Please note that HETAS Ltd Appliance Approval only covers the
use of wood logs. We always recommend using HETAS and Woodsure approved logs
with the “Ready to Burn” certication mark.
Only kiln-dried or well-seasoned wood with a moisture content reading of less than 18% is
recommended. A moisture meter is a handy device to have and is available from your
supplier. As a rule-of-thumb, wood seasons at about 1” (25mm) per year, so a log split
such that along its length no dimension is greater than 3” (75mm), it would take about 3
years to dry. A dry log will produce up to four and a half times more heat output than a
freshly cut log. Wet logs take heat to dry.
Wood burns best on a bed of ash and it is therefore only necessary to remove surplus ash
from the base of the rebox occasionally.
Burning wet or unseasoned wood will create tar deposits in the stove and chimney and
will reduce heat output. Tar deposits, if allowed to build up, are a major cause of
chimney res. This tar is also the main cause of blackened stove windows.
Once established and for the best results from your stove, load 1kg of good quality dry
wood per 45 minutes with the primary air control about half to two thirds closed. Logs
can be up to 300mm or 10” long.
Best burning depends on the quality of wood, draft and stove settings, so please do
experiment to nd your own best settings and the best position on your stove
thermometer.
13
Lighting the Stove
It is essential that you have three or four small res before you operate the stove to its
maximum heat output. This is to allow the paint to cure. We recommend this ‘running-in’
procedure after long shutdowns to preserve the life of stove. During the curing of the
paint you may notice an unpleasant smell and a slight vapour briey coming from the
top of the stove. It is not toxic, but for your comfort we would suggest that during this
period you leave doors and windows open.
First, load the re with starting fuel i.e. dry kindling timber (about the thickness of your
thumb) and/or relighters. Lighting paper is not recommended as it can cause excessive
smoke on start-up and produce too much ash. Firelighters are a much more efcient way
of lighting a woodburner. It is normal to see smoke come from the open stove door at this
stage.

GENERAL MAINTENANCE
ONLY EVER CARRY OUT MAINTENANCE WHEN THE STOVE IS COLD
The following elements of maintenance may be carried out by the householder. Any
structural repairs, e.g. panel, collar or stove pipe replacement must be carried out by a
suitably qualied installer. We recommend using a certied chimney sweep as sweeping
your own chimney can invalidate your home insurance policy.
Sweeping the Chimney - Your chimney should be cleaned each year before starting to
use your stove for the winter. Birds may have nested in the chimney or the masonry may
have cracked. Both chimney and ue pipe must be swept at least once a year. It is
recommended that you have your chimney swept every six months. It may be necessary
to sweep more frequently when damp wood is burnt regularly. The chimney can be
swept through your stove with the bafe plate removed. It is advisable to remove the
bricks too in order to avoid accidental damage.
Stove Body - The stove is nished with a heat-resistant paint and this can be cleaned with
a soft brush. Do not clean whilst the stove is hot – wait until it has cooled down. The nish
can be renovated with stove paint available from your supplier.
Glass Panels - Clean the glass panels when cool with stove glass cleaner. Highly abrasive
substances should be avoided as these can scratch the glass and make subsequent
cleaning more difcult. Wet logs on heated glass, a badly aimed poker or heavy
slamming of doors could crack the glass panels. The glass will not fracture from heat.
Should a glass panel require replacement, then remove the four screws and clips
retaining the glass frame, carefully remove the broken glass and replace the panel with
the correct stove glass from your supplier. Ensure you use new glass bre seal around its
edge, and use the steel frame, clips and screws to retain it in position.
Seasonal Maintenance - If your stove is being unused for any length of time, e.g. summer
months, then it is recommended that it is cleaned out thoroughly. Air slides should be
lightly oiled with Copaslip. Regular monitoring of the inside components will identify
condensation or water ingress. If these problems occur, then your stove needs to be
dried and the cause of the problem rectied. After a shut-down, and before reuse, the
appliance should be cleaned again and the chimney swept.
It is advised that you clean the appliance ue-ways, as well as monthly cleaning of the
bafe plate, especially when lighting up after a prolonged shut-down period. Ensure
access to cleaning doors where it is not possible to sweep the chimney through the
appliance.
14
SAFETY NOTES AND TROUBLESHOOTING
IT IS ESSENTIAL AND REQUIRED BY BUILDING REGULATIONS THAT A CO ALARM IS INSTALLED
IN THE SAME ROOM AS THIS APPLIANCE.
Fires Can Be Dangerous - Do not use this stove as an overnight burner, when nished for
the evening, leave the air controls open to allow the remainder of the fuel to burn out.
Use the glove provided to open the stove door when the stove is hot.
Never empty hot embers in to a bin, wait until the bed is cold before cleaning out.
Do Not Over-Fire - It is possible to re the stove beyond its design capacity, this could
damage the stove, so watch for signs of over-ring – if any part of the stove starts to glow
red, the re is in an over re situation, and the controls should be adjusted accordingly.
Never leave the stove unattended for long periods without adjusting the controls to a
safe setting – careful air supply control should be exercised at all times and only add the
recommended quantity of fuels.
Smoke and Fumes Entering the Room - When properly installed and operated, this
appliance will not emit fumes into the room. Occasional fumes from de-ashing and
refuelling may occur and is normal. Persistent fume emission with the doors closed must
not be tolerated.
If fume emission does persist, then the following immediate action should be taken:
1. Evacuate the room, opening doors and windows on your exit to ventilate the room.
2. Let the re go out, or eject and safely dispose of fuel from the appliance.
3. Check for a ue blockage and clean if required.
Do not attempt to relight the re until the cause has been identied and corrected. If
necessary, seek professional advice.
These situations are very dangerous and must NOT be tolerated. A list of Qualied
Engineers is available from:
HETAS Republic of Ireland
Severn House Irish National Fireplace Organisation
Unit 5 New Town Trading Estate 162 Chapel Street
Green Lane Dublin
Tewkesbury Ireland
GL20 8HD
Tel. [phone] Tel. [phone]
15

SAFETY NOTES AND TROUBLESHOOTING
Chimney Fire - Identied by loud roaring sounds, dense smoke and sparks exiting the
chimney. Shut down all air supply to stove by closing air vents, ensure the stove door fully
closed, call the Fire Brigade immediately. Regular chimney maintenance will prevent
chimney res. Seek advice from a qualied chimney sweep. Chimneys must be checked
at least annually or more often when poor quality fuels that are not recommended are
burnt.
Poor Heat Output - The stove may be too small for room. Seek advice from a qualied
heating engineer as to (kW) output required for room size. As a guideline the volume of
the room in cubic feet divided by 500 i.e. room 15’ x 15’ x 8’ would require 3.6kW approx.
Chimney and/or Flue Pipe Restricted, Room Ventilation Restricted - On Installation these
will have been checked but regular maintenance is necessary as conditions can change
i.e. soot build up, birds nesting, masonry fall, dust build up. Check Ventilation bricks dust
and blockages, ventilation should never be blocked or obscured intentionally by
furniture or other means.
Poor Quality Fuel - Only burn dry seasoned timber, soft woods have a lower heat output
than hard woods, see page 13.
Dirty Glass - Nearly always caused by poor fuel quality – check the moisture content of
the wood you are burning with a moisture meter.
Fire burning too low, open the air vents on the stove to create a hot re, this may ‘burn’
the glass clean.
If glass requires cleaning use stove glass cleaner from your supplier, only use glass cleaner
on cold glass. DO NOT USE abrasives or scrapers, these will scratch the glass making tar
build up harder to remove. NEVER spray aerosols near the appliance when it is alight.
Unburnt Fuel - Insufcient air reaching fuel - Adjust the air controls to supply combustion
air to burn fuel fully.
Keep Children Safe - Always use a reguard to BS 8423:2002 (Replaces BS 6539) in the
presence of children, aged and/or inrm persons.
16
SPARES
9
6
5
10
4
11 13
3
10
15
17
2
1
12
18
`
78
14
22 03 365ROLLER CATCH18
22 03 369TOP PLATE17
22 03 368TOP PANEL CENTRE CAP15
22 03 361FLUE BLANKING PLATE14
22 03 357DOOR COMPLETE
17
13
22 03 358DOOR GLASS CLIP12
22 03 359DOOR GLASS11
5
22 03 360DOOR HANDLE10
22 03 355BAFFLE9
22 03 367TOP BRICK RETAINER8
22 03 366TOP BRICK7
22 03 364RIGHT BRICK6
22 03 362LEFT BRICK5
22 03 354BACK BRICK4
22 03 356BASE BRICKS (SET)3
22 03 363LOG RETAINER2
22 03 353ADJUSTABLE FOOT (SET)1
CodeDescriptionPart Number

STOVE ACCESSORIES
The following is a list of stove accessories your retailer will be able to supply:
Matching graphite high temperature paint
Stove Glass Cleaner
Spare Rope (door 10mm soft/glass 10mm rope tape)
Rope Seal Adhesive
CO Detector
Stove Fan
Stove Thermometer
Wood Moisture Meter
Spare Glove
Permanent Ventilators
Purpose-built Ash Vacuum Cleaner
Ash Carrier
Fire Screens
Companion Sets
Log Baskets
Soot Box
RECYCLING AND DISPOSAL OF PRODUCT
To dispose of the stove after the product life has expired, please observe the following
information.
Dispose of the items correctly i.e. separate the parts to be disposed of in material
groups.
Always dispose of items in a way that is as sustainable as possible and that is in line with
the current environmental protection, reprocessing/recycling and disposal technology.
18
WARRANTY
Capital Wood Burning Stove Lifetime Warranty
This wood burning stoves are covered by a lifetime warranty (valid for original purchases
only) from date of sale. This warranty excludes the following naturally wearing
consumable items; Door glass, Firebricks, Rope seals, Bafe, Grate, and Paint nish.
In addition, the following criteria must be met:
• Sight of the data plate that should have been tted by the approved installer.
• Proof of installation by a HETAS or other approved body, or letter from Building Control
conrming that the installation was installed in accordance with the Building
Regulation.
• Proof of purchase from one of our approved suppliers.
• Proof of annual sweeping of chimney, at which time an inspection as to the
condition of both the chimney and the stove should be carried out to allow for
necessary maintenance to be performed.
• Only dry/seasoned wood with a moisture content of less than 20% has been used.
• Capital Fireplaces Ltd will accept no responsibility for installations which have been
carried out that are not in accordance to the Building Regulations or if the conditions
stated in these instructions are not adhered to. Warranty applies to parts only.
Please keep these instructions for future reference.
19

20
Capital Fireplaces Ltd.
Units 12-17
Henlow Trading Estate
Henlow Camp
Bedfordshire
SG16 6DS
Tel: [phone]
Fax: [phone]
Email: sales@capitalreplaces.co.uk
Website: www.capitalreplaces.co.uk