Fit the Downdraft in the opening, by inserting
it from above as shown in (Fig. 1).
Secure the downdraft inside the cabinet, by
using the special xing brackets supplied
with the product (Fig. 2). Insert the brackets
in the lower side of the downdraft, in such a
way that there is a 3 mm gap between the
lower side of the bracket and the bottom of
the cabinet (Fig. 3). This distance will allow
to pull the appliance downwards during in-
stallation, in order to make the stainless ste-
el frame perfectly adhere with the worktop.
Before inserting the screws into the cabinet,
please make sure that the appliance is per-
fectly perpendicular with the worktop.
After completing the installation and connec-
ting the appliance to the power supply, lift up
the downdraft by pressing on the glass, as
shown in (Fig. 4). If the Downdraft is equip-
ped with internal motor, install the power unit
directing the air outlet to the desired posi-
tion, either downwards or upwards (Fig. 5).
The motor can be installed on the front or on
the rear side of the downdraft. After installing
the motor, t the air outlet ducts.
If the Downdraft is equipped with external
motor, place the suctioning unit (external
motor) in a suitable area and t the exhaust
air ue. Then t the air outlet ducts between
the external motor and the downdraft. Select
the air outlet among the ve available op-
tions (Fig. 6) and t the union supplied with
the appliance.
Place the metal box containing the electro-
nic components in an easily reachable area
for possible technical assistance operations.
(Fig.7), by connecting the related connec-
tors (g. 8 A )
COOKER HOOD
1. Before carrying out the appliance installa-
tion, please check that all components are
not damaged, in such a case contact your
retailer and do not carry out any installation
operation.
Before the installation of the Downdraft,
please remove the safety piece you can see
in the picture (Fig. 1). Furthermore, please
read carefully all of the following installation
instructions.
• Useanairexhaustingpipewhosemaxi-
mum length does not exceed 5 meters.
•Limitthenumberofelbowsinthepiping,
since each elbow reduces the air capac-
ity of 1 linear meter. (Ex. : if you use no. 2
x 90 ° elbows, the length of piping should
not exceed 3 meters).
•Avoidabruptdirectionchanges.,
•Use a 150 mm. constant diameter pipe
for the whole length.
• Use piping approved by standards in
force.
The manufacturer shall not be deemed re-
sponsible for air capacity or noise problems
caused by failure to comply with the above
instructions and no warranty on the product
shall be provided.
2. Before making the hole, check that there are
no structural or other parts inside the cabi-
net, where the appliance is to be placed,
which could hinder a proper installation.
Check that the dimensions of the Downdraft
and the ones of the cook top are compatible
with the cabinet so that the installation can
be carried out properly.
3. Make a rectangular opening, 842 x 100 mm
in size, in the back of the cook top for the 90
cm model and 542 x 100 mm for the 60 cm
model and 1142 x100 mm for the 120 cm
model. In the version with the motor already
installed, remove the screws and the suc-
tioning unit in order to insert the down-draft
in the hole made.
4. Put the Downdraft in the opening, inserting it
from above as shown in (Fig. 2).
5. Fix the downdraft inside the cabinet, using
the special fixing brackets supplied with the
product (Fig. 3).
Insert the brackets in the lower side of the
downdraft (Fig. 3), in such a way that there
is a 2 mm distance between the lower side
of bracket and the bottom of the cabinet
(Fig. 3).
This distance will allow the traction to be po-
sitioned downwards of the product, at the
moment of fixing, in order to have the stain-
less steel trim perfectly adhering with the
work surface. Before inserting the screws,
please make sure that the appliance is per-
fectly perpendicular with the work surface.
6. Once the installation is complete and after
connecting the appliance to the mains pow-
er, lift up the downdraft and remove the door
block (Fig. 4); then open the door (Fig. 5)
and fit the filters in place (Fig. 6). In the ver-
sion of the Downdraft equipped with internal
motor, install the power unit orienting the air
outlet to the desired position, either down-
wards or upwards (Fig. 7).
The motor can be installed either on the front
or rear side of the downdraft After having in-
stalled the motor, connect the air ducts.
7. For versions with external motor, place the
suctioning unit (external motor) in a suitable
area and fit the exhaust air flue as illustrated.
Then fit the air outlet ducts between the ex-
ternal motor and the downdraft. Select an air
outlet from the five possibilities (Fig. 9) and
fit the union supplied with the appliance.
8. Place the metal box with the electronic com-
ponents in an easily reachable area for even-
tual technical assistance operations. (Fig.
9), connecting the three connectors (9 pole
connector for the actuator control and the
safety control, 4 pole connector for neon
lamp turn on and push-button connector)
(Fig. 10).
Make a rectangular opening, 790 x 100 mm
in size, in the back of the cook top .In the ver-
sion with the motor already installed, remove
the screws and the suctioning unit in order to
t the down draft in the opening made.
COOKER HOOD
1. Before carrying out the appliance installa-
tion, please check that all components are
not damaged, in such a case contact your
retailer and do not carry out any installation
operation.
read carefully all of the following installation
instructions.
• Useanairexhaustingpipewhosemaxi-
mum length does not exceed 5 meters.
• Limitthenumberofelbowsinthepiping,
since each elbow reduces the air capac-
ity of 1 linear meter. (Ex. : if you use no. 2
x 90 ° elbows, the length of piping should
not exceed 3 meters).
• Avoidabruptdirectionchanges.,
• Use a 150 mm. constant diameter pipe
for the whole length.
• Use piping approved by standards in
force.
The manufacturer shall not be deemed re-
sponsible for air capacity or noise problems
caused by failure to comply with the above
instructions and no warranty on the product
shall be provided.
2. Before making the hole, check that there are
no structural or other parts inside the cabi-
net, where the appliance is to be placed,
which could hinder a proper installation.
Check that the dimensions of the Downdraft
and the ones of the cook top are compatible
with the cabinet so that the installation can
be carried out properly.
3. Make a rectangular opening, 842 x 100 mm
in size, in the back of the cook top for the 90
cm model and 542 x 100 mm for the 60 cm
model and 1142 x100 mm for the 120 cm
model. In the version with the motor already
installed, remove the screws and the suc-
tioning unit in order to insert the down-draft
in the hole made.
4. Put the Downdraft in the opening, inserting it
from above as shown in (Fig. 2).
5. Fix the downdraft inside the cabinet, using
the special fixing brackets supplied with the
product (Fig. 3).
Insert the brackets in the lower side of the
downdraft (Fig. 3), in such a way that there
is a 2 mm distance between the lower side
of bracket and the bottom of the cabinet
(Fig. 3).
This distance will allow the traction to be po-
sitioned downwards of the product, at the
moment of fixing, in order to have the stain-
less steel trim perfectly adhering with the
work surface. Before inserting the screws,
please make sure that the appliance is per-
fectly perpendicular with the work surface.
6. Once the installation is complete and after
connecting the appliance to the mains pow-
er, lift up the downdraft and remove the door
block (Fig. 4); then open the door (Fig. 5)
and fit the filters in place (Fig. 6). In the ver-
sion of the Downdraft equipped with internal
motor, install the power unit orienting the air
outlet to the desired position, either down-
wards or upwards (Fig. 7).
The motor can be installed either on the front
or rear side of the downdraft After having in-
stalled the motor, connect the air ducts.
7. For versions with external motor, place the
suctioning unit (external motor) in a suitable
area and fit the exhaust air flue as illustrated.
Then fit the air outlet ducts between the ex-
ternal motor and the downdraft. Select an air
outlet from the five possibilities (Fig. 9) and
fit the union supplied with the appliance.
8. Place the metal box with the electronic com-
ponents in an easily reachable area for even-
tual technical assistance operations. (Fig.
9), connecting the three connectors (9 pole
connector for the actuator control and the
safety control, 4 pole connector for neon
lamp turn on and push-button connector)
(Fig. 10).
COOKER HOOD
1. Before carrying out the appliance installa-
tion, please check that all components are
not damaged, in such a case contact your
retailer and do not carry out any installation
operation.
Before the installation of the Downdraft,
please remove the safety piece you can see
in the picture (Fig. 1). Furthermore, please
read carefully all of the following installation
instructions.
• Useanairexhaustingpipewhosemaxi-
mum length does not exceed 5 meters.
• Limitthenumberofelbowsinthepiping,
since each elbow reduces the air capac-
ity of 1 linear meter. (Ex. : if you use no. 2
x 90 ° elbows, the length of piping should
not exceed 3 meters).
• Avoidabruptdirectionchanges.,
• Use a 150 mm. constant diameter pipe
for the whole length.
• Use piping approved by standards in
force.
The manufacturer shall not be deemed re-
sponsible for air capacity or noise problems
caused by failure to comply with the above
instructions and no warranty on the product
shall be provided.
2. Before making the hole, check that there are
no structural or other parts inside the cabi-
net, where the appliance is to be placed,
which could hinder a proper installation.
Check that the dimensions of the Downdraft
and the ones of the cook top are compatible
with the cabinet so that the installation can
be carried out properly.
3. Make a rectangular opening, 842 x 100 mm
in size, in the back of the cook top for the 90
cm model and 542 x 100 mm for the 60 cm
model and 1142 x100 mm for the 120 cm
model. In the version with the motor already
installed, remove the screws and the suc-
tioning unit in order to insert the down-draft
in the hole made.
4. Put the Downdraft in the opening, inserting it
from above as shown in (Fig. 2).
5. Fix the downdraft inside the cabinet, using
the special fixing brackets supplied with the
product (Fig. 3).
Insert the brackets in the lower side of the
downdraft (Fig. 3), in such a way that there
is a 2 mm distance between the lower side
of bracket and the bottom of the cabinet
(Fig. 3).
This distance will allow the traction to be po-
sitioned downwards of the product, at the
moment of fixing, in order to have the stain-
less steel trim perfectly adhering with the
work surface. Before inserting the screws,
please make sure that the appliance is per-
fectly perpendicular with the work surface.
6. Once the installation is complete and after
connecting the appliance to the mains pow-
er, lift up the downdraft and remove the door
block (Fig. 4); then open the door (Fig. 5)
and fit the filters in place (Fig. 6). In the ver-
sion of the Downdraft equipped with internal
motor, install the power unit orienting the air
outlet to the desired position, either down-
wards or upwards (Fig. 7).
The motor can be installed either on the front
or rear side of the downdraft After having in-
stalled the motor, connect the air ducts.
7. For versions with external motor, place the
suctioning unit (external motor) in a suitable
area and fit the exhaust air flue as illustrated.
Then fit the air outlet ducts between the ex-
ternal motor and the downdraft. Select an air
outlet from the five possibilities (Fig. 9) and
fit the union supplied with the appliance.
8. Place the metal box with the electronic com-
ponents in an easily reachable area for even-
tual technical assistance operations. (Fig.
9), connecting the three connectors (9 pole
connector for the actuator control and the
safety control, 4 pole connector for neon
lamp turn on and push-button connector)
(Fig. 10).
COOKER HOOD
1. Before carrying out the appliance installa-
tion, please check that all components are
not damaged, in such a case contact your
retailer and do not carry out any installation
operation.
Before the installation of the Downdraft,
please remove the safety piece you can see
in the picture (Fig. 1). Furthermore, please
read carefully all of the following installation
instructions.
• Useanairexhaustingpipewhosemaxi-
mum length does not exceed 5 meters.
• Limitthenumberofelbowsinthepiping,
since each elbow reduces the air capac-
ity of 1 linear meter. (Ex. : if you use no. 2
x 90 ° elbows, the length of piping should
not exceed 3 meters).
• Avoidabruptdirectionchanges.,
• Use a 150 mm. constant diameter pipe
for the whole length.
• Use piping approved by standards in
force.
The manufacturer shall not be deemed re-
sponsible for air capacity or noise problems
caused by failure to comply with the above
instructions and no warranty on the product
shall be provided.
2. Before making the hole, check that there are
no structural or other parts inside the cabi-
net, where the appliance is to be placed,
which could hinder a proper installation.
Check that the dimensions of the Downdraft
and the ones of the cook top are compatible
with the cabinet so that the installation can
be carried out properly.
3. Make a rectangular opening, 842 x 100 mm
in size, in the back of the cook top for the 90
cm model and 542 x 100 mm for the 60 cm
model and 1142 x100 mm for the 120 cm
model. In the version with the motor already
installed, remove the screws and the suc-
tioning unit in order to insert the down-draft
in the hole made.
4. Put the Downdraft in the opening, inserting it
from above as shown in (Fig. 2).
5. Fix the downdraft inside the cabinet, using
the special fixing brackets supplied with the
product (Fig. 3).
Insert the brackets in the lower side of the
downdraft (Fig. 3), in such a way that there
is a 2 mm distance between the lower side
of bracket and the bottom of the cabinet
(Fig. 3).
This distance will allow the traction to be po-
sitioned downwards of the product, at the
moment of fixing, in order to have the stain-
less steel trim perfectly adhering with the
work surface. Before inserting the screws,
please make sure that the appliance is per-
fectly perpendicular with the work surface.
6. Once the installation is complete and after
connecting the appliance to the mains pow-
er, lift up the downdraft and remove the door
block (Fig. 4); then open the door (Fig. 5)
and fit the filters in place (Fig. 6). In the ver-
sion of the Downdraft equipped with internal
motor, install the power unit orienting the air
outlet to the desired position, either down-
wards or upwards (Fig. 7).
The motor can be installed either on the front
or rear side of the downdraft After having in-
stalled the motor, connect the air ducts.
7. For versions with external motor, place the
suctioning unit (external motor) in a suitable
area and fit the exhaust air flue as illustrated.
Then fit the air outlet ducts between the ex-
ternal motor and the downdraft. Select an air
outlet from the five possibilities (Fig. 9) and
fit the union supplied with the appliance.
8. Place the metal box with the electronic com-
ponents in an easily reachable area for even-
tual technical assistance operations. (Fig.
9), connecting the three connectors (9 pole
connector for the actuator control and the
safety control, 4 pole connector for neon
lamp turn on and push-button connector)
(Fig. 10).
COOKER HOOD
1. Before carrying out the appliance installa-
tion, please check that all components are
not damaged, in such a case contact your
retailer and do not carry out any installation
operation.
Before the installation of the Downdraft,
please remove the safety piece you can
in the picture (Fig. 1). Furthermore,
read carefully all of the following installation
instructions.
• Useanairexhaustingpipewhosemaxi-
mum length does not exceed 5 meters.
• Limitthenumberofelbowsinthepiping,
since each elbow reduces the air capac-
ity of 1 linear meter. (Ex. : if you use no. 2
x 90 ° elbows, the length of piping should
not exceed 3 meters).
• Avoidabruptdirectionchanges.,
• Use a 150 mm. constant diameter pipe
for the whole length.
• Use piping approved by standards in
force.
The manufacturer shall not be deemed re-
sponsible for air capacity or noise problems
caused by failure to comply with the above
instructions and no warranty on the product
shall be provided.
2. Before making the hole, check that there are
no structural or other parts inside the cabi-
net, where the appliance is to be placed,
which could hinder a proper installation.
Check that the dimensions of the Downdraft
and the ones of the cook top are compatible
with the cabinet so that the installation can
be carried out properly.
3. Make a rectangular opening, 842 x 100 mm
in size, in the back of the cook top for the 90
cm model and 542 x 100 mm for the 60 cm
model and 1142 x100 mm for the 120 cm
model. In the version with the motor already
installed, remove the screws and the suc-
tioning unit in order to insert the down-draft
in the hole made.
4. Put the Downdraft in the opening, inserting it
from above as shown in (Fig. 2).
5. Fix the downdraft inside the cabinet, using
the special fixing brackets supplied with the
product (Fig. 3).
Insert the brackets in the lower side of the
downdraft (Fig. 3), in such a way that there
is a 2 mm distance between the lower side
of bracket and the bottom of the cabinet
(Fig. 3).
This distance will allow the traction to be po-
sitioned downwards of the product, at the
moment of fixing, in order to have the stain-
less steel trim perfectly adhering with the
work surface. Before inserting the screws,
please make sure that the appliance is per-
fectly perpendicular with the work surface.
6. Once the installation is complete and after
connecting the appliance to the mains pow-
er, lift up the downdraft and remove the door
block (Fig. 4); then open the door (Fig. 5)
and fit the filters in place (Fig. 6). In the ver-
sion of the Downdraft equipped with internal
motor, install the power unit orienting the air
outlet to the desired position, either down-
wards or upwards (Fig. 7).
The motor can be installed either on the front
or rear side of the downdraft After having in-
stalled the motor, connect the air ducts.
7. For versions with external motor, place the
suctioning unit (external motor) in a suitable
area and fit the exhaust air flue as illustrated.
Then fit the air outlet ducts between the ex-
ternal motor and the downdraft. Select an air
outlet from the five possibilities (Fig. 9) and
fit the union supplied with the appliance.
8. Place the metal box with the electronic com-
ponents in an easily reachable area for even-
tual technical assistance operations. (Fig.
9), connecting the three connectors (9 pole
connector for the actuator control and the
safety control, 4 pole connector for neon
lamp turn on and push-button connector)
(Fig. 10).
‘Before the installation of the Downdraft, ple-
ase remove the packaging,’ Furthermore,
please read carefully all of the following in-
stallation instructions.
7
