CARDINAL DVM SYSWALL45 Series Quick guide

CARDINAL DVM Keypad Modules
SYSBOXX
SYSWALL45
SYSWALL50
Assembly and Configuration Instructions
English Translation of the Original Operating Instructions
2/2020

Table of contents
Notices regarding these instructions and the manufacturer................................. 4
Keep these instructions available...................................................................................4
Design features of these instructions .............................................................................4
Copyright ........................................................................................................................5
Manufacturer’s address ..................................................................................................5
Safety ....................................................................................................................... 6
Intended use...................................................................................................................6
Basic safety instructions.................................................................................................6
Preventing material damage...........................................................................................6
Personnel qualification....................................................................................................7
Design features of notices of material damage..............................................................7
Description............................................................................................................... 8
Scope of delivery ............................................................................................................8
Required accessories.....................................................................................................8
Optional accessories ......................................................................................................9
SYSWALL45 keypad module .......................................................................................10
SYSWALL50 keypad module .......................................................................................11
SYSBOXX keypad module...........................................................................................12
Power supply unit .........................................................................................................13
Task and function .........................................................................................................14
Information on the type plate........................................................................................15
Technical data ..............................................................................................................15
Storing and transporting the product ................................................................... 16
Unpacking the product and checking the scope of delivery ............................... 17
Installing the product............................................................................................. 18
Installing SYSWALL45 keypad modules......................................................................18
InstallingSYSWALL50 keypad modules.......................................................................18
Installing SYSBOXX keypad modules..........................................................................19
Installing the power supply unit ....................................................................................20
Connecting the product......................................................................................... 22
Connecting the keypad module for standalone operation............................................22
Connecting the keypad modules for bus network operation ........................................23
Attaching keycaps to the keypad module ............................................................ 25
Configuring the product ........................................................................................ 26
Preparing installation ....................................................................................................26

Creating the configuration for keypad modules............................................................28
Commissioning keypad modules..................................................................................41
Concluding the configuration........................................................................................44
Troubleshooting.....................................................................................................45
Dismantling the product ........................................................................................46
Disposing of the product .......................................................................................47
Warranty declarations............................................................................................48

Notices regarding these instructions and the
manufacturer
4
Notices regarding these instructions and the
manufacturer
These instructions will help you to use the "CARDINAL DVM Keypad Module"
products safely. The "CARDINAL DVM Keypad Module" products are referred
to as "product" in the following unless the functions require differentiation.
These instructions apply to the following products:
•SYSWALL45 quadruple keypad module
−W45A-5554 anthracite
−W45S-1054 silver
−W45W-3454 pure white
•SYSWALL50 quadruple keypad module
−W50M-2243 stainless steel
−W50W-4443 white, high gloss
•SYSBOXX quadruple keypad module
−SYC1-3421 RAL 7016
−SYC1-3421-9006 RAL 9006
−SYC1-3421-9010 RAL 9010
Keep these instructions available
These instructions are part of the product.
Always keep the instructions on the product.
Pass on the instructions if you sell the product or pass it on in any other
way.
Design features of these instructions
Various elements of these instructions have fixed design features. As a result,
you can easily differentiate the following elements:
Normal text
•First-level enumeration
−Second-level enumeration
Action steps
Tips contain additional information.

Notices regarding these instructions and the
manufacturer
5
Copyright
These instructions contain information that is subject to copyright. These
instructions may not be copied, printed, filmed, processed, duplicated or
distributed in any form, either in whole or in part, without the prior written
permission of Sommer Cable GmbH.
©2019 Sommer Cable GmbH
All rights reserved.
Manufacturer’s address
Sommer Cable GmbH
Humboldtstraße 32-36
75334 Straubenhardt
Germany
Phone: [phone]
Fax: [phone]
E-mail: [e-mail]
Web: www.sommercable.com

Safety
6
Safety
Intended use
The product is designed to control media devices (audio or video devices) with
an RS232 interface at events and installations and in the broadcasting sector.
The product is intended for use in closed buildings.
Intended use also includes compliance with the accident prevention
regulations and the statutory regulations and standards applicable at the place
of use.
Intended use also comprises reading and understanding these instructions, as
well as observing and following all information therein, especially the safety
instructions.
Any other use is not deemed to be intended.
Basic safety instructions
Severe or fatal injuries due to electric shock are possible.
Have the modification of the power supply unit carried out by an authorized
electrician after consultation with the manufacturer.
Preventing material damage
Material damage due to use of the product under incorrect operating
conditions
Install the product in a dust-free environment.
Install the product protected against moisture, vapors, splash water and
wetness.
Install the product in a place protected from direct sunlight.
Do not install the product in the immediate vicinity of heat sources.
Use the product at ambient temperatures between 0 °C and 35 °C.
Material damage due to electrostatic charge
The product contains components sensitive to electrostatic charge. These
components may be damaged or destroyed by the effect of an electric field or
by charge equalization when touched.
Only store the product in a conductive ESD protection bag.
Before touching the product, establish electrical equipotential bonding
between yourself and your surroundings, e.g. using a wrist strap.
ESD protection field equipment is available for the safe handling of
electrostatically sensitive products.
Further information about electrostatic sensitive products can be found in
the EN 61340-5-1 and EN 61340-5-2 standards.

Safety
7
Personnel qualification
The instructions are intended for assembly and configuration personnel. The
following knowledge is required by assembly and configuration personnel:
•Knowledge in computer, network and media technology
•Knowledge and experience in assembly and configuration
The modification of the power supply unit configuration may only be
carried out after consultation with the manufacturer and by persons with
the additional qualification of "qualified electrician". Information on this
topic is available from the manufacturer.
Design features of notices of material damage
ATTENTION!
These notices warn of a situation that could lead to material
damage and limited functionality.

Description
8
Description
Scope of delivery
Depending on the variant or order, the following parts are included in the
scope of delivery:
SYSWALL keypad modules
•SYSWALL45/ 50 keypad module
•4 × keycap, clear
•1 × pre-perforated labeling sheet
•2 × screw (M2) for SYSWALL50
SYSBOXX keypad modules
•SYC1 keypad module
•4 × keycap, clear
•1 × pre-perforated labeling sheet
Power supply unit
•Power supply unit DVM-TAST-PSU, 2 × plug-in screw terminal (3-pin, RM
3.5 mm)
•Schuko, IEC C5 mains cable 180 cm
•2 × mounting bracket (SYFB01-MW)
•4 × screw for mounting brackets (S-G2508)
Required accessories
Depending on the variant or order, the following accessories are required for
mounting and connecting the product:
SYSWALL keypad modules
SYSWALL45
•Mounting frame W-MR-1 and/or W-MR-2 for installation in flush-mounted
cavity boxes
•Desktop connection panel (SYSFRAME45) for the installation of the keypad
module
•Trunking system with 45 mm rail (e.g. column housing W45S-Q62 or W45S-
R70) for installation of the keypad module
SYSWALL50
•Mounting frame W-MR-1 and/or W-MR-2 for installation in flush-mounted
cavity boxes
•Desktop connection panel (SYSFRAME50) for installation of the keypad
module
•2 × screw (M2)
•Screwdriver (TX6)

Description
9
SYSBOXX keypad modules
•SYSBOXX system (SYSBOXX, SYSDESK, SYSFLOOR, SYSTRUNK,
SYSBOARD) for the installation of the keypad module
•4 × screw (M2.5)
•Screwdriver TX8
Power supply unit
•SYSBOXX system (SYSBOXX, SYSDESK, SYSFLOOR, SYSTRUNK,
SYSBOARD) for the installation of the power supply unit
•4 × screw (M2.5)
•Screwdriver TX8
Network cable
•CAT5/CAT6/CAT7 network cable for connecting the power supply unit with
keypad modules and for connecting keypad modules with each other
Optional accessories
The following accessories are optionally available:
•Adapter cable “DVM-194-C4-xxx” for connecting the power supply unit to the
device to be controlled
•Adapter cable “DVM-194-C5-xxx” for direct connection of the keypad module
with the CARDINAL DVM HDBaseT built-in transmitters
(e.g. DVM-194-HDBT-T or W45W-3455). Operation without a power supply
unit is therefore possible.

Description
10
SYSWALL45 keypad module
No.
Designation
1
Key for controlling third-party media device
2
Detent
3
Programming key with LED lighting
4
USB port (type Mini-B)
5
Port 2 (RJ45, output)
6
Jumper for termination
7
Port 1 (RJ45, input)

Description
11
SYSWALL50 keypad module
No.
Designation
1
Key for controlling third-party media device
2
Programming key
3
USB port (type Mini-B)
4
Port 2 (RJ45, output)
5
Jumper for termination
6
Port 1 (RJ45, input)
7
Hole for fastening to SYSWALL system

Description
12
SYSBOXX keypad module
No.
Designation
1
Key for controlling third-party media device
2
Port 1 (RJ45, input)
3
Jumper for termination
4
Port 2 (RJ45, output)
5
USB port (type Mini-B)
6
Programming key with LED lighting
7
Hole for fastening to SYSBOXX system

Description
13
Power supply unit
No.
Designation
1
BUS 1 connection
2
Plug-in screw terminal (COM 1), 3-pin
3
Mains cable connection
4
Plug-in screw terminal (COM 2), 3-pin
5
BUS 2 connection
6
Hole for fastening (to SYSBOXX system, desk or wall)

Description
14
Task and function
Keypad modules
The keypad modules control individual functions of third-party media devices
that have an RS232 interface. The desired control function is programmed
using the “CARDINAL DVM Keypad Module System Configurator” software
and transferred to the third-party media device via the RS232 interface by
pressing a key on the module.
The keypad modules can be used in the following operating modes:
•Standalone operation
•Bus network operation
In standalone operation, only one keypad module (SYSBOXX or SYSWALL)
can be integrated into the system. With this module, two third-party media
devices can be controlled. The voltage supply and data communication are
implemented using network cables. For this purpose, the keypad module has
two ports (RJ45).
In bus network operation, up to 16 keypad modules (SYSBOXX or SYSWALL)
can be integrated into the system. Only one third-party media device can be
controlled in this operating mode. Both communication between the keypad
modules and the voltage supply are provided via ports 1 and 2 (RJ45) with
CAT6/CAT6A network cables. A modified RS485 protocol is used for
communication between the keypad modules.
To connect the keypad module or bus network to the third-party media device
to be controlled, the power supply unit has two 3-pin plug-in screw terminals
(COM 1 and COM 2), via each of which a separate bus signal can be
transmitted.
Power supply unit
The power supply unit supplies the keypad modules with the operating voltage
and simultaneously transmits the signals to the third-party media device. It can
be used in the following variants:
•Variant A (2 × power supply and 2 × serial connection, dual power supply
unit)
•Variant B (1 × power supply and 1 × serial connection, repeater)
•Variant C (1 × power supply and 2 × serial connection, mixed mode)
The delivery status of the power supply unit always corresponds to variant
C. In order to use the power supply unit in variants A and B, the power
supply unit must be modified. For this purpose, jumpers must be placed
inside the power supply unit. The variant may only be modified by
authorized electricians after consultation with the manufacturer. Further
information on this topic is available from the manufacturer.

Description
15
Information on the type plate
The type plate is glued to the power supply unit housing. It contains the
following information:
•Type designation of the power supply unit
•EAN code
•Serial number
•Disposal symbol
•CE marking (The product complies with the standards listed in the enclosed
declaration of conformity.)
Technical data
SYSWALL and SYSBOXX keypad modules
Connections
2 ports (RJ45)
USB port (type Mini-B, programming
interface)
Jumper for termination (2-pin)
Voltage supply
12 V via bus (RJ45 interface)
Power consumption (max.)
5 W
Temperature range (operation and
storage)
0–40 °C/-20–70 °C
Humidity during operation
0–90% (non-condensing)
Weight
SYSBOXX: approx. 120 g
SYSWALL45: approx. 75 g
SYSWALL50: approx.110 g
Dimensions W × H × D
SYSBOXX: 36 × 85 × 37 mm
SYSWALL45: 45 × 45 × 37 mm
SYSWALL50: 50 × 50 × 37 mm
Power supply unit
Connections
2 ports (RJ45)
2 plug-in screw terminals (RM3.50), 3-
pin
Voltage supply
90–250 V AC
Power consumption (max.)
22 W
Temperature range (operation and
storage)
0–40 °C/-20–70 °C
Humidity (during operation)
0–90% (non-condensing)
Weight
Approx. 414 g
Dimensions W × H × D
36 × 85 × 72 mm

Storing and transporting the product
16
Storing and transporting the product
Store the product in its original packaging.
Transport the product in its original packaging.

Unpacking the product and checking the scope of
delivery
17
Unpacking the product and checking the scope
of delivery
ATTENTION!
The product contains components sensitive to electrostatic
charge. These components may be damaged or destroyed by
the effect of an electric field or by charge equalization when
touched.
Before touching the product, establish electrical
equipotential bonding between yourself and your
surroundings, e.g. using a wrist strap.
Remove the product from the packaging.
Remove the parts of the product from the original packaging.
Keep the original packaging for later storage or possible return.
Check whether all parts of the product were delivered; for more information,
see page 8.
Check that the parts are in perfect condition.
Contact the manufacturer if parts are missing or damaged.

Installing the product
18
Installing the product
ATTENTION!
Material damage may be caused by using the product under
incorrect operating conditions.
Install the product in a dust-free environment.
Install the product protected against moisture, vapors,
splash water and wetness.
Install the product in a place protected from direct sunlight.
Do not install the product in the immediate vicinity of heat
sources.
Use the product at ambient temperatures between 0 °C
and 35 °C.
Installing SYSWALL45 keypad modules
The SYSWALL45 keypad modules can be installed in the following:
•Flush-mounted cavity boxes in combination with mounting frames W-MR-1
and/or W-MR-2
•Desktop connection panel (SYSFRAME45)
•Trunking systems with 45 mm rail
Installing SYSWALL45 keypad modules in a flush-mounted cavity box
To install a SYSWALL45 keypad module in a flush-mounted cavity box,
proceed as follows:
Attach the corresponding mounting frame to the flush-mounted cavity box.
Attach the mounting frame to the flush-mounted cavity box.
Insert the keypad module into the flush-mounted cavity box and press until
the detent engages audibly.
If necessary, attach the keycaps included in the scope of delivery with the
corresponding labels to the keypad module (see page 25).
Inserting SYSWALL45 into a desktop connection panel (SYSFRAME45) or
trunking system with a rail
To install a SYSWALL45 keypad module in a desktop connection panel
(SYSFRAME45) and/or a rail trunking system, proceed as follows:
Insert the keypad module into the corresponding system and press until the
detent engages audibly.
If necessary, attach the keycaps included in the scope of delivery with the
corresponding labels to the keypad module; (see page 25).
InstallingSYSWALL50 keypad modules
The SYSWALL50 keypad modules can be installed in the following:
•Flush-mounted cavity boxes in combination with mounting frames W-MR-1
and/or W-MR-2
•Desktop connection panel (SYSFRAME50)

Installing the product
19
Installing SYSWALL50 keypad modules in a flush-mounted cavity box
The following tool and materials are required for mounting:
•Two screws (M2)
•Screwdriver TX6
To install a SYSWALL50 keypad module in a flush-mounted cavity box,
proceed as follows:
Attach the corresponding mounting frame to the flush-mounted cavity box.
Attach the frame to the flush-mounted cavity box.
Place the keypad module in front of the mounting frame.
Tighten the screws with the TX6 screwdriver.
If necessary, attach the keycaps included in the scope of delivery with the
corresponding labels to the keypad module (see page 25).
Installing SYSWALL50 keypad modules in a desktop connection panel
(SYSFRAME50)
To install a SYSWALL50 keypad module in a desktop connection panel
(SYSFRAME50), proceed as follows:
Insert the keypad module into the desktop connection panel
(SYSFRAME50).
Fasten the keypad module to the desktop connection panel (SYSFRAME50)
with two screws (M2).
Tighten the screws with the TX6 screwdriver.
If necessary, attach the keycaps included in the scope of delivery with the
corresponding labels to the keypad module (see page 25).
Installing SYSBOXX keypad modules
The SYSBOXX keypad module can be installed in the following:
•SYSBOXX
•SYSDESK (desktop connection panel)
•SYSFLOOR (installation frame for floor tank)
•SYSTRUNK (trunking column profile)
•SYSBOARD (wall connection panel)
The following tool and materials are required for mounting:
•Four M2.5 screws
•Screwdriver TX8
To install a SYSBOXX keypad module in a SYSBOXX system, proceed as
follows:
Insert the keypad module into the corresponding system.
Fasten the keypad module with four screws (M2.5). In the process, tighten
the screws with the TX8 screwdriver.
If necessary, attach the keycaps included in the scope of delivery with the
corresponding labels to the keypad module (see page 25).

Installing the product
20
Installing the power supply unit
The power supply unit can be installed in the following:
•SYSBOXX system or
•separately (e.g. on a desk or wall)
The following tool and materials are required for mounting:
•Four screws (M2.5)
•Screwdriver TX8
•Mounting bracket (for individual assembly)
Installing the power supply unit in a SYSBOXX system
The power supply unit can be installed in the following:
•SYSBOXX
•SYSDESK (desktop connection panel)
•SYSFLOOR (installation frame for floor tank)
•SYSBOARD (wall connection panel)
ATTENTION!
Material damage may be caused by supplying power to the
power supply unit during installation.
Before installation, make sure that the power supply unit is
not connected to the power supply.
To mount the power supply unit on a SYSBOXX system, proceed as follows:
Insert the power supply unit into the SYSBOXX system.
Fasten the power supply unit to the housing with four screws (M2.5).
Tighten the screws with the TX8 screwdriver.