CARLO GAVAZZI UWP 3.0 User manual

REV 01 1 2023-07-10
Carlo Gavazzi UWP 3.0
Getting Started Guide for AWS IoT Core
Table of Content
Document revision history ............................................................................................................................1
Overview ......................................................................................................................................................2
Hardware description....................................................................................................................................2
User provided items ..................................................................................................................................2
3rd party purchasable items .......................................................................................................................2
Set up your development environment .........................................................................................................2
Tools installation (IDEs, Toolchains, SDKs) ..............................................................................................2
Set up device hardware ................................................................................................................................2
Setup your AWS account and permissions ...................................................................................................2
Create resources in AWS IoT .......................................................................................................................3
Provision the UWP 3.0 with credentials ........................................................................................................6
Verify messages in AWS IoT Core ...............................................................................................................6
Troubleshooting............................................................................................................................................6
Document revision history
Revision
Date
Description
REV01
2023/07/10
Publish document

REV 01 2 2023-07-10
Overview
This document describes how to connect a Carlo Gavazzi UWP 3.0 gateway to AWS IoT-Core.
Note: for further details about UWP 3.0 go to our website clicking here
Hardware description
The following UWP 3.0 models have been tested
Device name
Datasheet link
Installation manual link
Website page
UWP30RSEXXX
UWP 3.0 DS
UWP 3.0 IM
Link
UWP30RSEXXXSE
UWP 3.0 SE IM
Link
User provided items
None
3rd party purchasable items
None
Set up your development environment
Tools installation (IDEs, Toolchains, SDKs)
None
Set up device hardware
Following are the main steps:
1. Perform the UWP 3.0 commissioning
Note: for further details, read the installation manual
2. Connect the UWP 3.0 to the Internet.
Notes:
•For further details, read the quick guide connection
•Remember to set the DNS server properly from the System settings menu of the controller web app
Set up your AWS account and permissions
Following are the main steps:
3. Log into your AWS account
Note: click here for more information about how to set up an AWS IoT-Core account
4. Create AWS IoT resources for your device.
Notes:
A 5-step procedure will start (AWS IoT > Connect > Connect one device)
To get started, follow the steps outlined in the sections below:
•Sign up for an AWS account
•Create an administrative user
•Open the AWS IoT console
Pay special attention to the Notes.
Click here for more information about how to create AWS IoT resources.

REV 01 3 2023-07-10
Create resources in AWS IoT
Following are the main steps:
5. In Step 1 – Prepare your device, from point 4 copy the string, and paste it into a separate sheet deleting the word “ping”
as shown below.
This is the connection string that you will use in step 16
6. In Step 2 - Register and secure your device, enter a thing name and copy it into a separate sheet.
This is the client ID and the Topic that you will use in step 16
xxx

REV 01 4 2023-07-10
7. In Step 3 - Choose platform and SDK, set:
•Linux as device platform operating system
•Node.js as AWS IoT Device SDK
For UWP 3.0 is not necessary to run the connection kit (skip step 5 of the AWS IoT > Connect > Connect one device procedure)
8. To provision the UWP 3.0 with a signed AWS certificate, from your AWS IoT-Core account go to Security > Certificates
9. Click Add certificate > Create certificate
10. From Certificate, select Auto-generate new certificate, set the certificate status to Active and click create (as shown
below)

REV 01 5 2023-07-10
11. Download the Device certificate and Private key file as shown below.
Note: you will use these files in step 16.

REV 01 6 2023-07-10
Provision the UWP 3.0 with credentials
Following are the main steps:
12. Log into the UWP 3.0 Web App
13. From the Navigation bar, click to open the Main menu.
14. From the Services menu, select the AWS IoT service to open the configuration page.
15. From the Service configuration tile, click (under Service) to select Enable.
16. In the same tile, add the:
• Connection string (saved in step 5)
• Client ID (saved in step 6)
• Topic (saved in step 6)
• Security certificates
Note: click Upload certificate files to upload the Device certificate and the private key file saved in step 12
• Upload interval.
Note: The Start date is not available when the service is enabled.
17. Click Select variables to choose the devices that the Data Push service has to consider
Note: this menu shows the devices that have been enabled to log data in the UWP 3.0 database.
For more information about how to configure the database, read the UWP 3.0 Tool manual
18. Click to save the configuration.
19. From the Information tile, check on the service status.
The green Status icon informs you that the procedure has been completed successfully.
Click Show logs – OK to open the list of successfully loaded data.
Verify messages in AWS IoT Core
The AWS IoT MQTT client allows to view the data sent by your device.
Click here for more information about the client.
Troubleshooting
•From UWP 3.0 Web App, from the Information tile in Services> AWS IoT service, check on the service
status.
Element
Description
Status
Service status:
● Active / ● Inactive / ● Disconnected
Last data transmission
Date/time of the last data transmission
Show logs - OK
Logs lost successfully loaded
Show logs - Errors
Logs list errors
•For more information about AWS Troubleshooting click here