CARLO GAVAZZI SD2DUG24 Mounting instructions

SD2DUG24
Dupline generator
software manual
rev. 0.2, 10/08/2018

SD2DUG software manual 2
1 INDEX
1INDEX ...............................................................................................................................................2
2INTRODUCTION ................................................................................................................................4
2.1 GENERAL DESCRIPTION ...................................................................................................................4
2.2 HARDWARE REQUIREMENTS ............................................................................................................5
2.3 INSTALLATION ..............................................................................................................................5
3USER INTERFACE...............................................................................................................................6
3.1 MAIN PAGE .................................................................................................................................6
3.2 PROCEDURES................................................................................................................................8
Create a new configuration ....................................................................................................... 8
Open an existing configuration.................................................................................................. 8
Save a configuration .................................................................................................................. 8
Program analink channel........................................................................................................... 9
Program 8-bit binary protocol ................................................................................................... 9
Program 8-bit binary protocol with multiplexer ...................................................................... 10
Program 3 ½ digit BCD protocol............................................................................................... 10
Program 3 ½ digit BCD protocol with multiplexer.................................................................... 11
Multiplexer settings for 3 ½ digit BCD and 8-bit binary ........................................................... 12
EM24 alarms ....................................................................................................................... 12
EM24: multiplexer (transmission of analogue data) ........................................................... 13
Set A5 channel as reset of the EM24 counter...................................................................... 14
EM24: multiplexer (transmission of counter values) ........................................................... 14
Set B1 channel as reset of the EM24 counter ...................................................................... 16
Multiplexer settings for EM24 protocol............................................................................... 17
Clear output when bus is faulty ........................................................................................... 17
Set an output when bus is faulty ......................................................................................... 18
Split I/O................................................................................................................................ 18
Double scan ......................................................................................................................... 19
Connect the PC to the SD2DUG24 ....................................................................................... 19
Disconnect the PC from the SD2DUG24............................................................................... 20
Send a configuration to the SD2DUG24 .............................................................................. 21
Read a configuration from the SD2DUG24.......................................................................... 21
Upgrade the SD2DUG24 firmware ...................................................................................... 21
Set the name of a configuration .......................................................................................... 22
Set the number of Dupline channels.................................................................................... 22

SD2DUG software manual 3
Set the communication parameters .................................................................................... 23
Output status....................................................................................................................... 23
Set the password ................................................................................................................. 24
4FORMULAS .....................................................................................................................................25
4.1 PROCEDURES..............................................................................................................................25
Link a formula to an analogue value ....................................................................................... 25
Standard formula..................................................................................................................... 26
Customised formula ................................................................................................................. 26
5REPORT AND LIVE DATA .................................................................................................................28
5.1 PROCEDURES..............................................................................................................................28
Modbus map ............................................................................................................................ 28
Export the Modbus map .......................................................................................................... 28
Live data................................................................................................................................... 29
6G34960005 OR G34900000 QUICK SUBSTITUTION ..........................................................................30
6.1 PROCEDURES..............................................................................................................................30
Substitute a G34960005 .......................................................................................................... 30
Substitute a G34900000 .......................................................................................................... 31
7APENDIX .........................................................................................................................................32
7.1 BSI-TEMANA CONVERSION TABLE.................................................................................................32

SD2DUG software manual 4
2 INTRODUCTION
Welcome to the SD2DUG Software manual. This guide will cover the essentials of setting
up and using the SD2DUG software included with your Dupline®System.
This software tool has been designed for the configuration and updating of the Dupline
channel generator SD2DUG24: the communication parameters and the channel
programming are set-up locally in the PC, and then transferred to the generator through a
USB port. Likewise, data from the generator can be uploaded and modified.
To connect the PC to the SD2DUG any Micro-USB cable can be used (standard cable to
connect to Android smart-devices).
Important note:
Out of the factory, the SD2DUG24 has the following settings:
•It repeats the input channels onto the output ones
•The generated Dupline frame has 128 channels
•The Modbus parameters are:
oAddress = 1
oSpeed = 9600
oData bits = 8
oParity = None
oStop bit = 1

SD2DUG software manual 5
Should these settings fit the ones of the system, no further configurations are
needed and the SD2DUG24 can be directly powered and connected without any
programming.
•The program operates with Windows 7 or higher, with Microsoft .Net 4.5 or higher
installed
•A free USB port
Download the software file from the link...
Run the Setup DUG xxxx.exe file.

SD2DUG software manual 6
3 USER INTERFACE
When the DUG software is started, the following window will open:
B
A

SD2DUG software manual 7
The different areas are as follows:
Area
Description
A
The left panel contains:
Tab
Description
Configuration
To open new or already saved configuration or to save a
configuration
Connection
To connect the PC to a SD2DUG24 module
Device
To read a configuration from an SD2DUG24, to write a
configuration into an SD2DUG24, to update the firmware of an
SD2DUG24
Settings
To set different parameters, to set customised formulas, to copy
the setting of a G34900000 or a G34960005
Report and
live data
To export the Modbus map, to see live data on the Dupline bus
Info
To see info relevant to the software and firmware version, to open
the online manual
B
The right panel contains:
Tab
Description
Inputs
Matrix of the Dupline input channels
Channel
configuration
To select the Dupline protocols
Outputs
Matrix of the Dupline output channels

SD2DUG software manual 8
Create a new configuration
To create a new configuration, follow this procedure:
Step
Action
1
Click on
2
If a configuration is already open, choose an operation from:
a) Save
b) Do not save
c) Cancel action “New configuration”
Open an existing configuration
To open a configuration, follow this procedure:
Step
Action
1
Click on
2
Select the configuration to open
Save a configuration
To save a configuration, follow this procedure:
Step
Action
1
Click on (Save) or (Save as)
2
Select the folder where the configuration has to be saved.

SD2DUG software manual 9
Program analink channel
To program one or more channels as analink, follow this procedure:
Step
Action
1
Click onthe channel to be programmed(from A1 toP8): if oneor more channels
are selected, the underline is marked with a thicker line
Not selected channel
Selected channel
To select more channels, click and drag them
2
Click on the orange circle on the right side of Analink: the channels will be
marked in orange
Program 8-bit binary protocol
To program as 8-bit binary protocol, follow this procedure:
Step
Action
1
Click on one of the channels belonging to the group to be programmed:
2
Click on the brown circle on the right side of 8-bit: all the 8 bits belonging to the
group will be marked in brown

SD2DUG software manual 10
Program 8-bit binary protocol with multiplexer
To program as 8-bit binary protocol with multiplexer, follow this procedure:
Step
Action
1
Click on one of the channels belonging to the group to be programmed:
2
Click on the red square on the right of 8-bit binary: the whole group will be
marked in red and A1 to A4 output channels will be reserved for the multiplexer
A1 to A4 input channels are automatically set as split I/O.
Program 3 ½ digit BCD protocol
To program as 3 ½ digit BCD protocol, follow this procedure:
Step
Action
1
Click on one of the channels belonging to the first group to be programmed:

SD2DUG software manual 11
2
Click on the pink circle on the right side of 3 ½ digit BCD: all the 8 bits belonging
to the selected and following group will be marked in pink
Program 3 ½ digit BCD protocol with multiplexer
To program as 3 ½ digit BCD protocol, follow this procedure:
Step
Action
1
Click on one of the channels belonging to the first group to be programmed:
2
Click on the violet square on the right side of 3 ½ digit BCD: all the 8 bits
belonging to the selected and following group will be marked in violet and A1 to
A4 output channels will be reserved for the multiplexer
A1 to A4 input channels are automatically set as split I/O.

SD2DUG software manual 12
Multiplexer settings for 3 ½ digit BCD and 8-bit binary
To set the multiplexer parameters, follow this procedure:
Step
Action
1
Click on
2
To set how long the value of the multiplexer has to be maintained for, fill in the
field Keep multiplexer value for ...
3
The multiplexer values have to be defined in the Multiplexer values field:
To add a new value, click on
To switch beween single value or more values, click on
To delete an existing value, click on
EM24 alarms
To dedicate one input channel to the alarm output of the EM24, follow this procedure:
Step
Action
1
Click on the channel to be programmed as retransmission of setpoint alarms:
A maximum of two input channels can be programmed as alarm signals from
EM24
2
Click on the blue circle on the right side of EM24: the channel will be marked in
blue

SD2DUG software manual 13
EM24: multiplexer (transmission of analogue data)
To program the channels to detect the analogue values sent by one or more EM24s, follow
this procedure:
Step
Action
1
Click on one of the channels belonging to the first group to be programmed from
G to P:
2
Click on the light-blue square on the right side of EM24: all the 8 bits belonging
to the selected and following group will be marked in light-blue and A1 to A4
output channels will be reserved for the multiplexer
A5 is automatically reserved as the synchronization channel.
A1 to A5 input channels are automatically set as split I/O.

SD2DUG software manual 14
Set A5 channel as DMD synchronization or tariff
management
The A5 output value can be set in two ways:
a) Copying the status of any input channel
b) Via Modbus
Step
Action
1
Copying the status of any input channel
a) Click on
b) Select the input channel from the list, as shown below:
The status of this input will be reproduced on the sync channel A5
EM24: multiplexer (transmission of counter values)
To program the channels to detect the counter values sent by one or more EM24s, follow
this procedure:
Step
Action
1
Click on one of the channels belonging the first group to be programmed from
C to F:

SD2DUG software manual 15
2
Click on the blue square on the right side of EM24: all the 32 bits belonging to
the C, D, E and F groups will be marked in blue and B2 to B8 output channels
will be reserved for the multiplexer
B1 is automatically reserved as the reset channel.
B1 to B8 input channels are automatically set as split I/O.

SD2DUG software manual 16
Set B1 channel as reset of the EM24 counter
The B1 output value can be set in two ways:
c) Copying with the status of any input channel
d) Via Modbus
Step
Action
1
Copying with the status of any input channel
c) Click on
d) Select the input channel from the list, as shown below
The status of this input will be reproduced on the reset channel B1

SD2DUG software manual 17
Multiplexer settings for EM24 protocol
To set the multiplexer parameters, follow this procedure:
Step
Action
1
Click on
2
To set how long the value of the multiplexer has to be maintained for, fill in the
field Keep multiplexer value for ...
3
The multiplexer values have to be defined in the Multiplexer values field:
To add a new value, click on
To switch beween single value or more values, click on
To delete an existing value, click on
Clear output when bus is faulty
To program the output channels so that they are reset when the bus is faulty, follow this
procedure:
Step
Action
1
To enable this function, click on the icon
Check Clear ouput....
Set after how many seconds the output has to be reset
Click on Save
The action will automatically be applied to all the output channels

SD2DUG software manual 18
Set an output when bus is faulty
To program an output channel so that it is set when the bus is faulty, follow this procedure:
Step
Action
1
To enable this function, click on the icon
Check Clear ouput....
Set after how many seconds the output has to be reset
Click on Save
2
Click on the output channel to be programmed (from A1 to P8): if one or more
channels are selected, the underline is marked with a thicker line
Not selected channel
Selected channel
To select more channels, click and drag them
3
Click on the red circle on the right side of Bus faulty –set output: the channels
will be marked with a small circle next to the channel name
The status of the selected channel will be activated each time the bus is faulty
Split I/O
To program an input channel as split I/O, follow this procedure:
Step
Action
1
Click on the input channel to be programmed (from A1 to P8): if one or more
channels are selected, the underline is marked with a thicker line
Not selected channel
Selected channel
To select more channels, click and drag them

SD2DUG software manual 19
2
Click on the red arrows on the right side of Split I/O: the channels will be marked
with the same symbol below the channel name
Double scan
To enable the double scan on one or more input channels, follow this procedure:
Step
Action
1
Click on the input channel to be programmed (from A1 to P8): if one or more
channels are selected, the underline is marked with a thicker line
Not selected channel
Selected channel
To select more channels, click and drag them
2
Click on the red double bar on the right side of Double scan: the channels will
be marked with the same symbol next to the channel name
Connect the PC to the SD2DUG24
To connect to the SD2DUG24 generator, follow this procedure:
Step
Action
1
Connect the SD2DUG24 to your PC, using one of the following ports:
a) The Micro-USB port in the front part of the module –using a standard
USB cable
b) The RS485 port on the bottom of the module –using an RS485 to USB
converter

SD2DUG software manual 20
2
Select <auto detect> in the Connection menu, alternatively a Com port can
be selected together with the connection parameters
Things to know
•The software shows all the detected Com ports
•<auto detect> mode is available only when the Micro-USB port is used and
the connection parameters are 9600, 8, N, 1 and they cannot be changed
•If the Micro-USB port is used, address 0 can be used as the default address
•If the RS485 port is used, the modbus address of the SD2DUG24 has to be
used together with the proper connection parameters (the default address
out of the factory is 1, while the default parameters are 9600, 8, N,1)
3
Click on
4
The Dupline generator will connect to the PC and a green icon will be shown:
Disconnect the PC from the SD2DUG24
To disconnect, follow this procedure:
Step
Action
1
Click on
2
The Dupline generator will disconnect from the PC and a red icon will be
shown: