Carlos mendoza Showco PARLED 100 User manual

Showco PARLED 100
www.carlosmendoza.com.mx
Manual del usuario

2
Indexing
Part 1 Product
1.1— Product introduction……………………………………Page3
1.2— Safety Warning…………………………………………. Page5
1.3— Technical Specification………………………………….Page6
1.4— Photoelectric Data………………………………………Page7
Part 2Using DMX controller & Master / Slave
2.1 DMX Channel assignment…………….………..………..Page8
2.2 3.2 Software Profile………………………………...….Page8
Part 3 Using control panel
3.1 Display panel menu instruction……………………Page10
3.2 Display Menu instruction…………………………..Page11
www.carlosmendoza.com.mx

3
Part 1 Product
1.1 Product introduction
This product is designed for indoor use. It is suitable for indoor building, disco, stage and etc.
as large or small wash or effect lighting. This product can be operated as a single unit or in
multiple units for large applications. Direct input of DMX512 signal to unit to allow it be
controlled by any DMX512 controller. Powerful internal programs and friendly &
convenient operation interface allow customers to program freely to any different lighting
project requirements for installation or shows.
IMPORTANT
BEFORE OPERATION PLEASE CONFIRM THAT THE POWER SUPPLY STATED ON
THE REAR PANEL OF THIS UNIT IS THE SAME AS THE SUPPLIED MAINS POWER
IN YOUR AREA.
Check upon receipt
On receiving products, please carefully check that there has been no damage caused in
transportation and that the following parts are enclosed:
1XLP-336LEDPAR
1 X User manual
zAdditional spare parts may be supplied upon customer order
zREAD THIS USER MANUL CAREFULLY BEFORE OPERATION.
www.carlosmendoza.com.mx

4
www.carlosmendoza.com.mx

5
1.2 Safety Warning
This product must be installed by a qualified professional
* All operation and maintenance must be carried out in accordance with this
user manual
* Always disconnect the power before attempting to open the equipment
housing or carrying out any maintenance.
* Avoid looking directly into the light source (especially those who suffer
from epileptic fits)
* DO NOT connect power cable of other electric products with this unit.
* DO NOT connect DMX512 Signal cable of other electric products with this
unit.
* Make sure power socket is connected with earth cable well when connect to
AC110-220V power. The earth cable of this unit is Yellow/Green on
www.carlosmendoza.com.mx

6
1.3 Technical specification
AC90-259v, 50/60HzVoltage
AC230V----0.2A, AC115V---0.4A
Power 108W
36 *3W LED lampLight Source
Red 12pcs, Green 12pcs, Blue 12pcs
Lifespan around 100,000 hours
Beam angle 8 º、16º、25º、35 º、45º（standard 25 º）
Net Weight 5Kg
Size 34 x 31 x 22mm
Optical system: 1-256 grades electric adjustable, mini within 100msStrobe: at same step
speed adjustable strobe, random electric strobe, pulse strobe Cooling system: Heat cycle
cooling system with strong direct air .
● Operation mode:
Standard DMX512 signal (9 channels)
Intelligent ID addressing separately
Intelligent ID group addressing
● Display panel:
4-LED digital display DMX address code, test or run auto-programmes
● Auto-mode:
7 preset color change programs (Preset program parameters changeable by DMX
console)
7 program parameters changeable
Master/Slave mode without DMX console
www.carlosmendoza.com.mx

7
1.4 Photoelectric diagram
Red color
Green color
0
1
2
3
1
2
3
2 4 6 8 10 Distance(m)
15°
1145 290 130 72 50 LUX
Beam opening (m)
0
0
0
1
1
1
2
2
2
3
3
3
1
1
1
2
2
2
3
3
3
2
2
2
4
4
4
6
6
6
8
8
8
10 Distance(m)
10 Distance(m)
10 Distance(m)
15°
15°
15°
1780
300
2750
460
76
700
210
35
320
120
20
190
90 LUX
15 LUX
145 LUX
Beam opening (m)Beam opening (m)
Beam opening (m)
Blue color
White color
0.52 1.05 1.57 2.10 2.60 Diameter(m)
0.52 1.05 1.57 2.10 2.60 Diameter(m)
0.52 1.05 1.57 2.10 2.60 Diameter(m)
0.52 1.05 1.57 2.10 2.60 Diameter(m)
·
·
15
www.carlosmendoza.com.mx

8
Part 2 Master/Slave & Using DMX Controller
Channel Function & Effect DMX Value
CH1 Dimmer 0~255% 0-255
CH2 RED 0~255% 0-255
CH3 GREEN 0~255% 0-255
CH4 BLUE 0~255% 0-255
CH5 COLOR MACRO (7 preset color effect) 0-255
CH6 AUTO PROGRAMS (7 preset programs & 7 edit
programs）0-255
CH7 Strobe 0-255
CH8 Program change time
Program run time 0-127 128-255
CH9 IPADDRESS 0-255
2.1 Software Profile
The system will loading the manufacturer’s setting and show the
information by the Digital Tube when it is opened by the first time . For
checking the Digital tube function , you could also set up as below :
SET→LOAD→ON .
Each time when you open the model , the system will show
the manufacturer and the Software format（ATRT VER1.0，or you
could press ESC pass by these information ）,then load the User’s
setting.
ADJ→CAL is White Balance’s calibrate Menu ,it is for
calibration the RGB Color (Using Software to calibrate the the
www.carlosmendoza.com.mx

9
differents of the Hardware ) , SET→LOAD→ON is not useful
for this Menu (ADJ → CAL),So this menu with the Password
management , only the persons who has got the Password could
operate it .
During the Slave Mode (SXXX) or the Master (MXXX), when
you press UP or DOWN , could enter the right DMX ADDRESS setting
surface to meet the quickly amending DMX effect .
During No. Amending status , the Right No; will be shining ,
and Press UP or DOWN for 1.5 Sec , the No. will stop to shine , then
could change the No. as soon as possible .
www.carlosmendoza.com.mx

10
Part 3 Using Display Panel
3.1Display Menu instruction
www.carlosmendoza.com.mx