Carrier HYPERSTAT User manual

For more information, contact your local Carrier Controls Expert
©2023 Carrier. All Rights Reserved. Cat. No. 11-808-959-01
INTRODUCTION
HyperStat is a wall-mount thermostat. Its thoughtful design ensures that it blends into most
commercial spaces while still giving a fresh and contemporary feel compared to dated
building control interfaces.
PACKAGE CONTENTS
•HyperStat device
•Mounting accessories
SPECIFICATIONS
Power
Power Source: 24V AC/DC input (+/- 15%)
Peak consumption: 1.4VA Maximum
Operating range
Temperature 32 to 122°F (0°C to 50°C)
Humidity 20-85% non-condensing.
Communication
Sensor bus for daisy chained sensor communication and low power 3V dc.
4-wire interface for RS 485 communication @ 115200 baud and 5V
DC, 100mA power source
900-928 MHz Mesh IEEE 802.15.4-compliant, for communications to CCU
Bluetooth: BLE 4.1 for commissioning, and communication to wireless sensors
Onboard Sensors
Temperature range of 32 to 122°F with an accuracy of +/-1°F
Humidity 0 to 100% with an accuracy of 2%
CO2 sensor with a range of 0 - 40,000 ppm, accuracy of +/-30ppm
VOC sensor; Typical Accuracy: 15% of measured value; TVOC: 0 - 60,000
ppb;
Occupancy sensor based on passive infrared (PIR) with adetection range of
4m with a 15-degree angle
Light Sensor. Ambient light sensor • <100 LUX resolution • High-accuracy UV
index sensor • Matches erythermal curve
Sound sensor with 40-120dB response for 100Hz to 10KHz
PM2.5, PM10 sensor (optional). Detection range of 0-1000µg/m3 and accuracy
of +/-10µg/m3 (PM2.5, 0-100µg/m3) or +/-25µg/m3 (PM10, 0-
100µg/m3). Maximum long-term mass concentration precision limit drift:
•0 to 100 µg/m3 ±1.25 µg/m3/year
•100 to 1000 µg/m3 ±1.25 % mV/year
Inputs
2 x 10K Type-2 thermistor inputs with 2% accuracy
2 x 0-10V Analog voltage inputs with 2% detection accuracy (2-10V)
Touch slider for temperature control along with 3 mechanical buttons
HYPERSTAT
(7C-HS-C2W-X)
INSTALLATION GUIDE
Scan this QR
code to get a
more detailed
version of the
Installation
Guide

For more information, contact your local Carrier Controls Expert
©2023 Carrier. All Rights Reserved. Cat. No. 11-808-959-01
Outputs
6 x Relays rated for 24V DC/1A
3 x 0-10V or 4-20mA analog outputs
2.8" 240x320 pixel TFT display
PRECAUTIONS
:
•Failure to wire devices with correct polarity when using a shared transformer,
may result in damage to any device powered.
•Never connect or disconnect the wiring with the power ON.
•Do not allow the powered wires to touch the circuit boards.
•Always install complying with all state and local codes.
•Do not assemble the front to the back plate while it is powered on.
•Once Installed the HyperStat takes seven days to auto-calibrate and settles at a
steady state value.
•Avoid mechanical stress on the CO2 sensor to get accurate readings.
MOUNTING
1. HyperStat Interface - Conventional
5. Rubber cover 2
2. HyperStat Main 6. Gang Box
3. Allen head screws
7. PHP screws
4. Rubber cover 1 8. Backplate

For more information, contact your local Carrier Controls Expert
©2023 Carrier. All Rights Reserved. Cat. No. 11-808-959-01
1. HyperStat Interface - Conventional
5. Rubber cover 2
2. HyperStat Main 6. Gang Box
3. Allen head screws
7. PHP screws
4. Rubber cover 1 8. External Antenna
1. Place the HyperStat Interface-Conventional and the back plate (only if the gang box is
fixed vertically) on the gang box such that the back plate covers the gang box and fix
these two items to the wall gang box with the PHP screws provided in the box.
2. Now align the HyperStat main to lock onto the HyperStat Interface-Conventional.
3. Use the Allen head screws to make this entire setup tamper-proof.
4. Rubber covers 1 and 2 must be fixed to cover the programming pins.
5. Connect the antenna to the device as shown in the above figure. Rotate the antenna
clockwise to lock it in place.
DIS-ASSEMBLING
1. If the HyperStat is mounted on the wall, hold the front plastic with both hands and pull it
away from the wall.
2. If you are holding the HyperStat in your hands, insert a flat head screwdriver in the notch
provided (marked by the two arrows shown in the image) between the front and back
plastic and twist to separate them.

For more information, contact your local Carrier Controls Expert
©2023 Carrier. All Rights Reserved. Cat. No. 11-808-959-01
Note
:
•Favorable for Pollution degree 2 or the equivalent •Rated impulse voltage – 330V
•Type action – Type 1. C •Operating Ambient Temperature:
0°C to 50 °C
•The method of connection/disconnection for screwless
terminals is mentioned in the article pointed by the QR
label on the box.
•Indoor Use Only
•Terminal Identification – In the Operating Manual •Powered by Class 2 Power Source
CARRIER CLIMAVISION TECHNICAL SUPPORT
Installation and servicing of Control Systems can be hazardous due to electrical
components. Only trained and qualified service personnel should install, repair or service
control system components.
For more information on wiring, commissioning, or usage of the ClimaVision product line,
please refer to any documentation provided with the job. If no documentation was provided
with the job, please use the ClimaVision Help Center (support.climavision.com) where you
can find application specific wiring schematics and helpful user guides and videos or scan
the QR code here:
If you need help beyond that, please reach out to your local Carrier distributor for support.
Scan this QR code to
get a more detailed
version of the
Installation Guide