Carson Cv550 User manual

Evaporative Cooler - CV550

User Manual

[Revision 1.0 October 2018]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY

DAMAGE AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by

this manual may vary in appearance, assembly, inclusions, specifications, description and packaging.

Evaporative Cooler - CV550

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death,

injury or equipment or property damage if not understood or followed. Safety messages have the

following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you

do not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you

do not follow instructions.

You CAN be INJURED if you

do not follow instructions or

equipment damage may occur.

It is vital that you read and understand

this user manual before using the

product, including safety warnings, and

any assembly and operating instructions.

Keep the manual for future reference.

Safety precautions and recommendations

detailed here must be fully understood

and followed to reduce the risk of injury,

fire, explosion, electrical hazard, and/or

property damage.

Safety information presented here is

generic in nature – some advice may not

be applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery

powered or combustion engine powered.

•Before Use - If you are not familiar with

the safe operation/handling of the

equipment, or are in any way unsure of

any aspect of suitability or correct use

for your application, you should

complete training conducted by a

person or organization qualified in safe

use and operation of this equipment,

including fuel/electrical handling and

safety.

•Do NOT operate the equipment in

flammable or explosive environments,

such as in the presence of flammable

liquids, gases or dust. The equipment

may create sparks or heat that may

ignite flammable substances.

•Keep clear of moving parts.

•Equipment may be a potential source

of electric shock or injury if misused.

•Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

•Do NOT allow others to use the

equipment unless they have read this

manual and are adequately trained.

•Keep packaging away from children -

risk of suffocation! Operators must use

the equipment correctly. When using

the equipment, consider conditions and

pay due care to persons and property.

General Work Area Safety

•Work areas should be clean and well it.

•Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

•If devices are provided for connecting

dust extraction / collection facilities,

ensure these are connected and used

properly. Dust collection can reduce

dust-related hazards.

General Personal Safety

•Wear appropriate protective equipment

when operating, servicing, or when in

the operating area of the equipment to

help protect from eye and ear injury,

poisoning, burns, cutting and crush

injuries. Protective equipment such as

safety goggles, respirators, non-slip

safety footwear, hard hat, hearing

protection etc should be used for

appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective

equipment. Do not wear loose clothing

or jewellery, which can be caught in

moving parts. Keep hair and clothing

away from the equipment.

•Stay alert and use common sense

when operating the equipment. Do not

over-reach. Always maintain secure

footing and balance.

•Do not use the equipment if tired or

under the influence of drugs, alcohol or

medication.

•This equipment is not intended for use

by persons with reduced physical,

sensory or mental capabilities.

General Fuel Safety

•Petrol/fuel/gasoline is extremely

flammable – keep clear of naked

flames or other ignition sources.

•Do not spill fuel. If you spill fuel, wipe it

off the equipment immediately – if fuel

gets on your clothing, change clothing.

•Do NOT smoke near fuel or when

refuelling.

•Always shut off the engine before

refuelling.

•Do NOT refuel a hot engine.

•Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

•Always refuel in well ventilated areas.

•Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•Using a combustion engine indoors

CAN KILL IN MINUTES. Engine

exhaust contains carbon-monoxide – a

poison you cannot smell or see.

•Use combustion engines OUTSIDE

only, and far away from windows, doors

and vents.

General Equipment Use and Care

•The equipment is designed for

domestic use only.

•Handle the equipment safely and

carefully.

•Before use, inspect the equipment for

misalignment or binding of moving

parts, loose components, damage or

any other condition that may affect its

operation. If damaged, have the

equipment repaired by an authorised

service centre or technician before use.

•Prevent unintentional starting of the

equipment - ensure equipment and

power switches are in the OFF position

before connecting or moving

equipment. Do not carry equipment

with hands or fingers touching any

controls. Remove any tools or other

items that are not a part of the

equipment from it before starting or

switching on.

•Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be

safer when used within its design and

usage parameters.

•Use the equipment and accessories

etc. in accordance with these

instructions, considering working

conditions and the work to be

performed. Using the equipment for

operations different from those

intended could result in hazardous

situations.

•Always keep equipment components

(engines, hoses, handles, controls,

frames, housings, guards etc) and

accessories (cutting tools, nozzles, bits

etc) properly maintained. Keep the

equipment clean and, where

applicable, properly lubricated.

•Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the

equipment near flammable materials,

combustible gases or liquids etc.

•The equipment is not weather-proof,

and should not be stored in direct

sunlight, at high ambient temperatures

or locations that are damp or humid.

•Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

•For specific equipment safety use and

care, see Equipment Safety.

Evaporative Cooler - CV550

General Electrical Safety

•Inspect electrical equipment, extension

cords, power bars, and electrical fittings

for damage or wear before each use.

Repair or replace damaged equipment

immediately.

•Ensure all power sources conform to

equipment voltage requirements and

are disconnected before connecting or

disconnecting equipment.

•When wiring electrically powered

equipment, follow all electrical and

safety codes.

•Wherever possible, use a residual

current device (RCD).

•High voltage / high current power lines

may be present. Use extreme caution

to avoid contact or interference with

power lines. Electrical shock can be

fatal.

General Electrical Safety

•Electrically grounded equipment must

have an approved cord and plug and

be connected to a grounded electrical

outlet.

•Do NOT bypass the ON/OFF switch

and operate equipment by connecting

and disconnecting the electrical cord.

•Do NOT use equipment that has

exposed wiring, damaged switches,

covers or guards.

•Do NOT use electrical equipment in wet

conditions or in damp locations.

•Do NOT use electrical cords to lift,

move or carry equipment.

•Do NOT coil or knot electrical cords,

and ensure electrical cords are not trip

hazards.

General Service Information

•The equipment must be serviced or

repaired at authorised service centres

by qualified personnel only.

•Replacement parts must be original

equipment manufacturer (OEM) to

ensure equipment safety is maintained.

•Do NOT attempt any maintenance or

repair work not described in this

manual.

•After use, the equipment and

components may still be hot – allow the

equipment to cool and disconnect

spark plugs and/or electrical power

sources and/or batteries from it before

making adjustments, changing

accessories or performing repair or

maintenance.

•Do NOT make adjustments while the

equipment is running.

•Perform service related activities in

suitable conditions, such as a

workshop.

•Replace worn, damaged or missing

warning/safety labels immediately.

Evaporative Cooler Safety

•For household use only.

•Connect the appliance to a single-

phase AC supply of the voltage

specified on the rating label.

•Always turn the product to the OFF

position and unplug it from the

electrical outlet when not in use.

•Extreme caution is necessary when the

appliance is used by or near children,

invalids or elderly person.

•Do not run cord under carpeting and do

not cover cord with throw rugs, runners

or the like. Arrange cord away from

traffic area and where it will not be

tripped over.

•Do not operate the appliance with a

damaged cord or plug, or after the unit

malfunctions, has been dropped, or

damaged in any manner.

•If the supply cord is damaged, it must

be replaced by the manufacturer or its

service agent or a similarly qualified

person to avoid a hazard.

•After adding water, do not let machine

tilt, collide, laid or move to any position

that will make the water overflow. Do

not overturn the machine.

Evaporative Cooler Safety

•Use the appliance in a well-ventilated

area. While using, distance of no less

than 20cm should be kept away from

wall or corner to ensure the air intakes

or exhaust openings should not be

blocked unexpectedly. The unit must

not be located immediately below or

besides a curtain or the likes.

•Do not insert or allow fingers or any

other objects into grill to avoid a

mechanical danger when in use. Do not

block air intakes or exhaust openings in

any manner.

•Adequate clean water should be put

into the tank within the water level limits

as shown by the water level indicator.

Make sure that you DO NOT add water

whilst the power is on.

•If you want to move the product whilst

water is in the tank, unplug it and push

it slowly and very lightly on the side of

the unit to avoid water spillage. The

best method would be to drain the unit

using the valve at the bottom of the

unit.

•Do not cover the air outlet, a clear

space of at least 1 meter should be

provided in front and back of the

machine.

Evaporative Cooler Safety

•Please keep the ice crystals box

provided away from children, as it is a

chemical based substance that is

harmful if swallowed. Also make sure

that the ice pack is not placed in direct

sunshine. The ice crystal can be used

over 5 years. When scrapping the

appliance, follow the regulations

concerning the disposal of ice crystals.

•Use the appliance on flat, dry floor only.

•This appliance is not intended for use

by persons (including children) with

reduced physical, sensory or mental

capabilities, or lack of experience and

knowledge, unless they have been

given supervision or instruction

concerning use of the appliance by a

person responsible for their safety.

•Children should be supervised to

ensure that they do not play with the

appliance.

•Don’t let people with poor physical

ability, slow response or mental

disorder (include children) use the

machine unless the person with sense

of safety responsibility can assist them.

Evaporative Cooler - CV550

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols

on your product and their meanings. If any stickers become unreadable, unattached etc, replace them.

Flammable Material Hazard

Flammable liquids, gases or

substances etc may present.

Avoid ignition sources and

open flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc

before using the product.

Use Hand Protection

Wear appropriate hand

protection and take due care

as the product or use of the

product may present hand

hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be

fatal.

Electrocution / Electrical

Shock Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling

electrical products, cables,

plugs and leads. Electrical

shock can be fatal.

Toxic Fumes / Dust Hazard

Using the product or by-

products from use may

produce fumes, smoke or

particles that could be harmful

if inhaled. Wear appropriate

breathing protection and have

adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases or

substances etc may be

present. Avoid ignition sources

and open flames. Danger of

explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices

that can cause severe cut

injury to fingers, limbs etc.

Take due care when handling

and using the product.

Crush Hazard

The product may have blades,

edges or mechanical devices

that can cause severe crush

injury to fingers, limbs etc.

Take due care when handling

and using the product.

Single Operator Only

The product must be operated

by a single person only. More

than one person operating the

product may introduce

additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care

as the product or use of the

product may present face and

eye hazards.

Use Foot Protection

Wear appropriate foot

protection and take due care

as the product or use of the

product may present foot

hazards.

Use Eye / Ear / Head

Protection

Wear appropriate eye and / or

ear and / or head protection

and take due care as the

product or use of the product

may present eye, hearing and

head hazards.

Running Hazard

Do not run on or near the

product as doing so may

present a fall hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or

objects that can cause severe

injury to fingers, limbs, blood

etc. Take due care when

handling and using the

product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures

and hot surfaces that can

cause burn injuries.

Flying Debris Hazard

Be aware that the product or

use of the product may

present hazards produced by

flying debris. Wear appropriate

clothing and protectiove

devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts

to stop fully before handling

the product, adjusting,

maintenence etc.

Evaporative Cooler - CV550

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be

fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due

care when handling and using

the product.

Slope / Fall Injury Hazard

Be aware that using the

product on sloping surfaces or

in slippery conditions may

present additional dangers

from falls and contact with

blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

maneouvres as this may result

in severe injury due to falling,

product breakage or collapse

etc.

Electrocution / Electrical

Shock Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do

NOT use in rain, damp or wet

conditions. Electrical shock

can be fatal.

Electrocution / Electrical

Shock Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product.

Always disconnect the product

from the electrical supply

before handling the product,

adjusting, maintenence etc.

Power Line Electrocution

Hazard

High voltage / high current

power lines may be present.

Use extreme caution to avoid

contact or interference with

power lines. Electrical shock

can be fatal.

"Kick-Back" Hazard

High level of "kick-back"

hazard that can cause the

machine to suddenly rotate

towards operator. Kick-back

injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch

to move people.

Winch Lift Hazard

Do NOT LIFT load vertically.

Use machine to PULL only.

Cable Hazard

Ensure that load bearing cable

is not kinked or knotted.

Winch Cable Hazard

Ensure that there is a

minimum number of cable

coils on winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye

protection for welding. Dorect

exposure to weld arcs may

cause permanent eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser, or allow

others to.

Evaporative Cooler - CV550

Table of Contents

Safety...................................................................................................................................................2

Safety Symbols ..........................................................................................................................................4

Introduction ........................................................................................................................................7

Parts Identification.............................................................................................................................8

Set-Up..................................................................................................................................................9

Operation ..........................................................................................................................................10

Control Panel Operation........................................................................................................................... 10

Speed Settings ..................................................................................................................................10

Cool Settings .....................................................................................................................................10

Swing Settings................................................................................................................................... 11

Usage Conditions.....................................................................................................................................11

Maintenance .....................................................................................................................................11

Cleaning the Interior.................................................................................................................................11

Troubleshooting...............................................................................................................................12

Specifications...................................................................................................................................12

Evaporative Cooler - CV550

Introduction

Evaporative air cooler is a kind of modern energy-saving product which is developed through years of

research and experiments. It has the following advantages:

•Energy-saving: Up to 80% or more while comparing with traditional air-conditioner.

•Environment protection: No discharge of hazardous substances and freon free during its

operation.

•Efficient: Achieving the maximum cooling and purifying effect with minimum power consumption.

Evaporative air cooler is developed as a new generation of products combining of climatic conditions,

which is using a new generation of blades with high speed and large air volume.

Its working principle is a "direct evaporative" humidification and cooling technology. Not only have

cooling become functional, but it can also achieve a cooling effect on air humidification. A continuously

circulating pump draws water from the water tank, and then distributes the water to the wet curtain.

When hot air enters into the wet curtain, which is a cell-type filter layer made of special material, it

exchanges energy with water. A satisfactory effect of cooling can then be obtained. Cool, clean air is

blown indoors under a precise pressure point rendered by the air blower while the hot air goes out of

the room through open vents or windows. This cycle achieves the goal of lowering the temperature in

the room.

CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON

Evaporative Cooler - CV550

Parts Identification

No. Name

1 Water/ small ice cube inlet

2 Control panel

3 Water supply inlet

4 Water level indicator

5 Casters

1

2

3

4

5

CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON

Evaporative Cooler - CV550

Set-Up

1. Open the carton and take out the unit.

2. When adding water, open the water inlet on the top cover, pour water into the water tank, then

observe the water level indicator with the floating ball inside and pay attention to the following:

−Avoid getting water into the motor and its surrounding area to avoid damaging the electrical

components.

−Water must be below the ‘H’ level, otherwise it will overflow.

−Use fresh, clean water.

3. Press and hold the power button for a few seconds to turn ON/OFF the unit, then you can select the

settings for speed, swing and cooling.

• In high humidity season, it is better to choose wind mode as there is humidifying effect

in cool mode. • After adding water, do not let the unit tilt, collide, lie down or move to

any position that can spill water. Do not overturn the unit. • Do not cover the air outlet; a clear, open

space of at least 1 metre should be provided at the front and back of the unit. • Ensure to always unplug

the unit before cleaning or maintaining it. • Clean the outer casing with a clean, damp cloth. Don’t

splash it directly with water. • If the unit is spilling water, pull out the power plug immediately. You

should only turn the unit ON again only after it thoroughly dries out, otherwise, it may short-circuit and

malfunction. • Do not position the air outlet close to walls or window curtains because the air current will

be blocked. • If the unit is not in use, pull out the power plug. • Do not let people with poor physical

ability, slow responsiveness, mental disorders and/or children use the unit unless said person has a

sense of safety/responsibility and someone can assist them in operating the unit.

CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON

Evaporative Cooler - CV550

Operation

Due to the remarkable advantages of evaporative air cooler in cooling, humidification, cleanliness,

energy-saving and ventilation, it is used primarily in locations where ventilation and cooling are needed.

This product is mainly used in the following places:

•Electronics, electroplating, footwear, printing, plastics, clothing, packaging, the food processing

industry.

•Textiles, machinery, ceramics, chemical industry, metallurgy, glass, metal, leather and other

manufacturing industries.

•Hospital, clinic, schools, waiting rooms, cafes, shopping malls, supermarkets, laundry rooms.

•Offices, home, kitchens, market, large entertainment centres, underground parking lots, stations

and other public places.

•Greenhouses, flower farms, poultry, livestock, and other types of farms.

•Existing chiller for air conditionings and as an auxiliary equipment used in blowers.

•Places of high humidity required for indoor use.

Control Panel Operation

After plugging the unit into a 220V-240V/50Hz power outlet, it will be in stand-by mode with a buzzer

ringing.

Speed Settings

Connect the unit to the power supply and turn the SPEED knob. The fan

will start. You can change the speed with the following choices; 1 (Low),

2 (Medium) and 3 (High). Turn the SPEED to “0” to turn the unit OFF.

Cool Settings

Turn the COOL knob to “ON” to start the cooling process, it will be on Fan

Mode only after you have turn it to OFF.

CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON

Evaporative Cooler - CV550

Swing Settings

•

Vertical Louvers

Turn the SWING knob to ON. The vertical louvers will automatically

begin to move from right to left.

•

Horizontal Louvers

Manually adjust the horizontal louvers to change the airflow from up to

down.

Usage Conditions

•Ambient temperature: 10 – 45°C.

•Environment’s Relative Humidity: ≤ 95%

•Atmospheric pressure: 86 – 106kpa

•0°C < Water supply temperature < 45°C

•Water supply pressure: 0.15 – 0.6mpa

•Voltage deviation does not exceed the rated voltage of ± 10%

•Environmental air quality should meet ambient air quality standard GB3095-1996.

•No corrosive gases should be present.

Maintenance

Turn the power to OFF first before performing any maintenance or repairs on the unit to prevent

electrical accidents. To ensure that the cooling effect of the unit is maintained, the unit’s body should be

cleaned with water every day or every week. The interior of the unit should also be cleaned regularly.

The proper cleaning interval is once a month, but the actual cleaning time will vary depending on the

exterior environment.

Cleaning the Interior

1. Pull out the water drain plug and clear away any signs of dirt deposits in the chassis with water.

2. Remove the air inlet shutter together with the evaporating heat exchanger. Wash them thoroughly

with water, then re-install them back.

• While cleaning the unit, use only a low water pressure. When cleaning the wet curtain, do not

use acidic or alkaline based detergents. • It is recommended that the user and equipment

supplier agree to a maintenance and repair schedule to carry out regular maintenance on the unit and

to ensure that it will always be in good condition.

CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON

Evaporative Cooler - CV550

Troubleshooting

Troubles Common Causes Solutions

Unable to start the fan.

Power failure. Check power supply.

Switch burned. Change the switch.

No air flow.

Motor starter’s capacitor is damaged. Change the capacitor

Motor is damaged. Change the motor

There is an obstruction in the wet

curtain or air filter.

Clean out the wet curtain and/or air

filter.

Unit is not emitting cool air.

Lack of or no water in the water tank. Add water.

Water pump is damaged. Change the water pump.

Wet curtain is dirty. Clean wet curtain.

Unpleasant odour Water or honeycomb cooling pad is

dirty.

Change the water and clean the

honeycomb cooling pad.

Specifications

Model CV550

Voltage 240V

Power Source Electric

Water Tank Capacity 55L

Max. Airflow 3000m³/h

Wattage 220W

Fan Axial

Functions Cooler, Fan, Purifier, Humidifier

Power Supply 240V/50Hz

Usage Indoor/Outdoor

Room size 15-30㎡

Noise Level ≤55dB

Speed 3

Water consumption 2-3L/h

Power Plug Australian Standard

CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON CARSON

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety

Consult all documentation, packaging

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.

Before each use, check the product for

loose/broken/damaged/missing parts,

wear or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear or leaks.

Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.

Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.

The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.

This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business

or employee, or financially affect the user, business or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement or service by a technician

may cause financial loss, loss of employee time or an

inconvenience requiring compensation.

If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

Carson CV550 User manual

Popular Air Cleaner manuals by other brands