Casa Lusso SP175CH User manual

www.casalusso.com.au
Spin Progressive Wall Mixer - Installation Instructions
CONGRATULATIONS ON THE PURCHASE OF YOUR NEW CASA LUSSO TAPWARE,
WE HOPE YOU AND YOUR FAMILY ENJOY YOUR NEW PRODUCT AND CONSIDER US
FOR ANY FUTURE PROJECT. CASA LUSSO PRODUCTS HAVE BEEN MANUFACTURED
UNDER THE HIGHEST STANDARDS OF QUALITY AND WORKMANSHIP.
FAILURE TO COMPLY WITH ANY OF THE ABOVE INSTRUCTIONS WILL VOID ALL WARRANTIES
FEATURES
GENERAL INFORMATION
Product Code: SP175CH / SP175MB / SP175BB
Premium Warranty (Domestic Use) :
Lifetime Flühs cartridge replacement only
7 year Replacement products and parts1
1 year parts & labour2
Material: Plated Solid Brass Construction
Made to Australian Standards code:
AS/NZS 3718
Water supply - Tapware LN030023
1 Excludes Damage to ceramic disk cartridges from pieces
of copper tube, plastic tube, sand, dirt or thread tube etc.
All speciality finishes are subject to 2 year replacement
product and parts and 1 year replacement product and
parts & labour. 2Jumper valves and ceramic disk spindles;
1 year parts only.
MAINTENANCE
• Clean regularly using mild soap and dry with a soft cloth.
• Do not use abrasive cleaners, harsh detergents or citrus based cleaners on any products
as these will scratch the surface.
• Tightening or adjustment of Tapware over time is considered general maintenance.
• Failure to clean/replace aerators/flow restrictors as required will void warranty.
• Damage to finishes that arise from installation or post installation will void warranty.
The warranty will not apply if:
• The product has been damaged by improper use;
• The product has not been used in accordance with any applicable instruction guide;
• The purchaser has attempted to modify or repair the product;
• The purchaser has failed to observe the cleaning and maintenance guidelines;
• The product is not installed by a licenced Plumber.
• Flow controllers/ aerators not regularly cleaned/ replaced.
Product warranties are personal to the person who acquires the product for their own consumption or use and not for resale
or resupply. Claims with this product cannot be made by anyone other than the consumer. Where a product is covered by
parts and labour warranty, the warranty covers both the repair of the defective part or the provision of a spare part to
replace the defective part and the installation of that part.Where a product is covered by parts only, the warranty covers
both the repair of the defective part or the provision of a spare part in replacement. It does not include the removal of the
defective part or the installations of the repaired or replaced part. We reserve the right to provide minor components (e.g.
handles, aerators, hoses, dress rings and washers) as ‘Parts Only’ to the customer. Casa Lusso reserves the right to alter, or
amend this warranty offer in writing at any time.
LIFETIME
WARRANTY
Chrome
SP175CH
Matte Black
SP175MB Brushed Brass
SP175BB

Spin Progressive Wall Mixer - Installation Instructions
www.casalusso.com.au
FAILURE TO COMPLY WITH ANY OF THE ABOVE INSTRUCTIONS WILL VOID ALL WARRANTIES
CONTENTS










Handle
Hex Key Screw
Screw
Washer
Sleeve
Base Plate
O-ring
Pressing Nut
Flühs Catridge
Mixer Body
IMPORTANT
IT IS IMPORTANT TO FLUSH OUT THE WATER
PIPES BEFORE INSTALLING THE MIXER.
Hot and cold water inlet pressures should be equal.
Inlet pressure range: 150 – 500 kPa
New Regulation:
500 kPa maximum operating pressure at any
outlet within a building. (Ref. AS/NZS 3500)
Maximum hot water temperature: 80oC.
INSTALLATION
1. The thickness of your Tile/Glue/Sheet should be calculated prior
to installation; it is suggested that a Nogging should be set 64mm
in from the estimated outside finished Tile/Wall to give you
adjustment +/-6mm. Alternatively see below:
Setting the Nogging 40mm behind the face of wall stud will give
you a Tile/Glue/Sheet thickness variance of 18-30mm.
Setting the Nogging 45mm behind the face of wall stud will give
you a Tile/Grout/Sheet thickness variance of 13-25mm.
2. Level the top point of the mixer and fix using screws to Nogging,
making sure the Mixer is aligned square.
IT IS IMPORTANT TO FLUSH OUT THE WATER PIPES BEFORE
INSTALLING THE MIXER
3. Connect the water supply to the Hot/Cold inlets of the mixer
body marked H and C.
While there is construction in process after mixer body is installed,
we recommend removal of the dress finishing’s (i.e handle etc)
until final fit off to ensure the finishing’s aren’t scratched or
damaged by trades. The nominated hole cut out for the tiler
should be 30-40mm diameter.
5. For fit off, screw on the base plate and place handle over to
assess fit, if the handle can be pushed back to 1-2mm from finished
wall then tighten the Hex Key to fit, if not the Brass sleeve has a
nominated cut-off line that will give you the adjustment to push
the handle back another 2-10mm Do not cut past the cut-off line.
6. Re-install Handle on to mixer body whilst in off position,
positioning the off (•) symbol to the top of the mixer, tighten Hex Key.










30-40mm tile cutout
Nogging
58-70mm
Nominated
optional
cut-off line