Casa Lusso SPIN 62025BN User manual

www.casalusso.com.au
.
FAILURE TO COMPLY WITH ANY OF THE ABOVE INSTRUCTIONS WILL VOID ALL WARRANTIES
SPIN Pull Down Sink Mixer - Installation Instructions
15 YEAR
WARRANT Y
Brushed Nickel
62025BN
FEATURES
GENERAL INFORMATION
Product Code: 62025BN / 62025MB
Premium Warranty (Domestic Use) :
15 year Ceramic cartridge replacement only
7 year Replacement products and parts1
1 year parts & labour2
Material: Solid Brass Construction
WELS: WELS 6 Star, 4.5 litres per minute
1 Excludes Damage to ceramic disk cartridges from pieces
of copper tube, plastic tube, sand, dirt or thread tube etc.
All speciality finishes are subject to 2 year replacement
product and parts and 1 year replacement product and
parts & labour. 2Jumper valves and ceramic disk spindles;
1 year parts only.
MAINTENANCE
• Clean regularly using mild soap and dry with a soft cloth.
• Do not use abrasive cleaners, harsh detergents or citrus based cleaners on any products
as these will scratch the surface.
• Tightening or adjustment of Tapware over time is considered general maintenance.
• Failure to clean/replace aerators/flow restrictors as required will void warranty.
• Damage to finishesthat arise from installation or post installation will void warranty.
The warranty will not apply if:
• The product has been damaged by improper use;
• The product has not been used in accordance with any applicable instruction guide;
• The purchaser has attemptedto modify or repair the product;
• The purchaser has failed to observe the cleaning and maintenance guidelines;
• The product is not installed by a licencedPlumber.
• Flow controllers/ aeratorsnot regularly cleaned/ replaced.
Product warranties are personal to the person who acquires the product for their own consumption or use and not for resale
or resupply. Claims with this product cannot be made by anyone other than the consumer. Where a product is covered by
parts and labour warranty, the warranty covers both the repair of the defective part or the provision of a spare part to
replace the defective part and the installation of that part.Where a product is covered by parts only, the warranty covers
both the repair of the defective part or the provision of a spare part in replacement. It doesnot include the removal of the
defective part or the installations of the repaired or replaced part. We reserve the right to provide minor components (e.g.
handles, aerators, hoses, dress rings and washers) as ‘Parts Only’ to the customer. Casa Lusso reserves the right to alter, or
amendthis warrantyoffer in writing at any time.
Made to Australian Standards code:
AS/NZS 3718
Water supply - Tapware LN022530
Matte Black
62025MB
ONGRATULATIONSON THE PURCHASE OF YOUR NEW CASA LUSSO TAPWARE,
WE HOPE YOU AND YOUR FAMILY ENJOY YOUR NEW PRODUCT ANDCONSIDER US
FORANYFUTURE PROJECT. CASA LUSSO PRODUCTS HAVE BEEN MANUFACTURED
UNDER THE HIGHEST STANDARDS OF QUALITYANDWORKMANSHIP
C

IMPORTANT
IT ISIMPORTANT TO FLUSH OUT THE WATER
PIPES BEFORE INSTALLING THE MIXER.
Hot and cold water inlet pressures should be equal.
Inlet pressure range: 150 – 500 kPa
New Regulation:
500 kPa maximum operating pressure at any
outlet within a building. (Ref. AS/NZS 3500)
Maximum hot water temperature: 80oC.
www.casalusso.com.au
FAILURE TO COMPLY WITH ANY OF THE ABOVE INSTRUCTIONS WILL VOID ALL WARRANTIES
1. Install the flexible hoses into the mixer and hand tighten in place.
The flexible hoses are to be fitted into the correct inletsfor hot water
and for cold water (Red band for hot and blue band for cold).
DO NOT USE SPANNER TO TIGHTEN ASIT CAN DAMAGETHE O RING
2. Place the mixer into position and secure using the horse
shoe and fixing nut.
IT ISIMPORTANT TO FLUSH OUT THE
WATER PIPES BEFORE INSTALLING THE MIXER.
3. Ensure gauze strainers are placed into the flexible hoses
then connect the isolating taps.
CONTENTS



















Silicon Gel Pipe
Hose
Magnet Seat
M3*10 Screw
Union Nut
Bush
Washer
O-Ring
Bush
O-Ring
Round Iron
Connecting Sleeve
Spray
Magnet
Escutcheon
O-Ring
Connect
Valve Body
O-Ring
Inlet Assy
Inlet Assy
Bracket
Washer
Washer
Bush
O-Ring



















INSTALLATION
Washer
Plug Botton Kit
Bush
Bush
Valve
Nut
Bonnet
M5*4 Screw
Handle
Valve Body
Shank
Base Escutcheon
O-Ring
Washer
Washer
Nut
Screw
Inlet Hose (Cold)
Inlet Hose (Hot)
Check Valve
SPIN Pull Down Sink Mixer - Installation Instructions