Casio IT-9000 Series User manual

Handheld Printer Terminal
User’s Guide
Be sure to read “Safety
Precautions” inside this
guide before trying to use
your Handheld Printer
Terminal.
E
Series
IT-9000

Information in this document is subject to change without advance notice. CASIO Computer Co.,
Ltd. makes no representations or warranties with respect to the contents or use of this manual
and specifically disclaims any express or implied warranties of merchantability or fitness for any
particular purpose.
BLUETOOTH is a registered trademark owned by Bluetooth SIG, Inc. and licensed to
CASIO COMPUTER CO., LTD.
Microsoft and Windows are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
“FeliCa” is a contactless IC card technology developed by SONY Corporation and a
registered trademark of SONY Corporation.
•
•
•

E-1
Contents
Safety Precautions .........................................................................................E-3
Operating Precautions ...................................................................................E-9
Important ......................................................................................................E-11
After Service ...................................................................................................... E-11
Regulatory Information ................................................................................E-12
Checking in the Box .....................................................................................E-14
Handheld Printer Terminal System Configuration.....................................E-15
General Guide ...............................................................................................E-17
Loading and Removing the Battery Pack...................................................E-21
Loading ..............................................................................................................E-22
Removing...........................................................................................................E-23
Charging the Battery Pack ..........................................................................E-24
USB Cradle/Ethernet Cradle/Cradle-type Battery Charger ...............................E-24
Car Mounted-type Battery Charger....................................................................E-24
Dual Battery Charger .........................................................................................E-25
AC Adaptor ........................................................................................................E-25
Handling the Hand Strap .............................................................................E-26
Handling the Neck Strap..............................................................................E-27
Attaching............................................................................................................E-27
Removing...........................................................................................................E-28
Attaching the Stylus Holder...............................................................................E-28
Configuring Handheld Printer Terminal Settings.......................................E-30
Calibrating Touch Screen Alignment ................................................................. E-30
Setting the Display Brightness....................................................................E-31
Adjusting Display Brightness ............................................................................E-31
Display Auto Dimmer ........................................................................................ E-31
Using the CMOS Imager (Imager Models) .................................................E-32
Using the Printer...........................................................................................E-33
Installing the Roll Paper..................................................................................... E-33
Attaching the 58 mm Paper Width Adjuster ......................................................E-35
Precautions When Using Printer........................................................................E-36
Handling SD Memory Cards ........................................................................E-38
Installing.............................................................................................................E-38
Removing...........................................................................................................E-38
Handling SIM/SAM Cards ............................................................................E-39
Installing.............................................................................................................E-39
Removing...........................................................................................................E-40

E-2
Handling Magnetic Card Reader.................................................................E-42
Handling the NFC Reader/Writer ................................................................E-43
RFID Tags ..........................................................................................................E-43
Contactless IC Cards..........................................................................................E-43
Performing Communications ......................................................................E-45
Bluetooth®Communication ...............................................................................E-45
GSM/W-CDMA Communication ......................................................................E-46
GPS ....................................................................................................................E-46
Resetting the Handheld Printer Terminal ...................................................E-47
Performing a Full Reset (Initialization) ............................................................E-47
Warning Label ...............................................................................................E-49
IT-9000 Specifications .................................................................................E-50
Using the USB Cradle (HA-L60IO)...............................................................E-57
General Guide .................................................................................................... E-57
Connecting the USB Cradle Power Supply .......................................................E-59
Specifications .....................................................................................................E-62
Using the Ethernet Cradle (HA-H62IO) .......................................................E-63
General Guide .................................................................................................... E-63
Connecting the Ethernet Cradle Power Supply..................................................E-65
Specifications .....................................................................................................E-68
Using the Cradle-type Battery Charger (HA-L30CHG)..............................E-69
General Guide .................................................................................................... E-69
Connecting the Cradle-type Battery Charger Power Supply .............................E-71
Specifications .....................................................................................................E-73
Using the Car Mounted-type Battery Charger (HA-L35CHG)...................E-74
General Guide .................................................................................................... E-74
Connecting the Car Mounted-type Battery Charger Power Supply...................E-75
Specifications .....................................................................................................E-77
Using the Dual Battery Charger (HA-G32DCHG).......................................E-78
General Guide .................................................................................................... E-78
Charging Battery Pack ....................................................................................... E-80
Connecting Multiple Dual Battery Chargers......................................................E-81
Specifications .....................................................................................................E-82
Using the Rechargeable Battery Pack (HA-G20BAT) ................................E-83
Specifications .....................................................................................................E-83

E-3
Safety Precautions
Congratulations upon your selection of this CASIO product. Be sure to read the
following Safety Precautions before trying to use it for the first time.
Your neglect or avoidance of the warning and caution statements in the
subsequent pages causes the danger of fire, electric shock, malfunction and
damage on the goods as well as personal injury.
Markings and Symbols
The following are the meanings of the markings and symbols used in these Safety
Precautions.
Danger This symbol indicates information that, if ignored or applied
incorrectly, creates the danger of death or serious personal injury.
Warning
This symbol indicates information that, if ignored or applied
incorrectly, creates the possibility of death or serious personal
injury.
Caution
This symbol indicates information that, if ignored or applied
incorrectly, creates the possibility of personal injury or property
damage.
A diagonal line indicates something you should not do. The symbol shown
here indicates you should not try to take the unit apart.
A black circle indicates something you should do. The symbol shown here
indicates you should unplug the unit from the wall outlet.
Warning
Disassembly and Modification
Never try to disassemble or modify the Handheld Printer Terminal and its
options including battery pack and battery in any way.
Abnormal Conditions
Should the Handheld Printer Terminal and/or its options including battery
pack and battery become hot or start to emit smoke or a strange odor,
immediately turn off the power and contact your dealer or distributor whom
you purchased the product from, or an authorized CASIO service provider.
•
•
•
•

E-4
Warning
Dust and Moisture
Though the Handheld Printer Terminal is dust and water splash resistant,
its options including the battery pack are not. Keep loose metal objects and
containers filled with liquid away from your Handheld Printer Terminal
and the options. Also, never handle the Handheld Printer Terminal and the
options while your hands are wet.
Laser Light
The Handheld Printer Terminal emits laser light.
Never look directly into the laser light or shine the laser light into anyone’s
eyes.
•
•
Warning
Interference with the Operation of Other Equipment
(Using Wireless Data Communication)
Keep your Handheld Printer Terminal at least 22 centimeters (811/16") away
from anyone wearing a pacemaker. Radio waves emitted by the Handheld
Printer Terminal can affect the operation of a pacemaker.
Before the use in aircraft, be sure to consult with cabin crew for interference
the Handheld Printer Terminal emits.
Before the use in medical facility, be sure to consult with the facility
management or the manufacture of a specific medical equipment that the
Handheld Printer Terminal may interfere with.
Do not use the Handheld Printer Terminal nearby gas pump or chemical tank
or any other places flammable or explosive.
Human exposure
To comply with the relevant European RF exposure compliance
requirements, a separation distance of at least 8.2cm in RFID operation must
be maintained between the Handheld Printer Terminal's reader port and the
operator body. This Handheld Printer Terminal must not be co-located or
operating in conjunction with other transmitter.
•
•
•
•
•

E-5
Caution
Foreign Objects
Take care to ensure that metals or combustible objects are not inserted into
the openings of the Handheld Printer Terminal or its options, and not to
allow moisture to get inside of them.
Location
Install the cradle properly on a flat and stable surface so that it cannot fall
down onto floor.
LCD Screen
Never apply strong pressure to the screen or subject it to strong impact.
Doing so can crack the LCD Screen.
Do Not Touch Internal Components
Never touch any high-voltage components. This can cause an electric
shock.
Printer
Do not touch the areas around the printer motor or head since they can
become very hot. Doing so can cause burns.
Touching any of the gears while they are turning with unprotected hands
can cause personal injury. Be careful not to come in contact with turning
gears.
Contact with the blade installed in the paper outlet can cause personal
injury. Be careful not to touch the blade.
•
•
•
•
•
•
•
Warning
Avoiding Traffic Accidents
Never use your Car Mounted-type Battery Charger while operating a motor
vehicle. Park your vehicle in a safe place before performing any operation.
Never locate the Car Mounted-type Battery Charger where it might interfere
with proper operation of the vehicle.
Locate connecting cables as instructed by the manual, avoiding locations
that can interfere with driving operations.
Car Battery Power
Should the Car Power Cable become damaged, replace it immediately with
a new Car Power Cable when using the Car Mounted-type Battery Charger.
•
•
•
•

E-6
Caution
Installing in Vehicle
To save your vehicle’s battery from running down, be sure that the Car
Power Cable should be unplugged from the cigarette lighter socket when
you do not use the Car Mounted-type Battery Charger and that the use of
the battery charger should be avoid while the vehicle’s engine is turned off.
Do not handle the Car Power Cable with wet hands.
Install the Car Mounted-type Battery Charger at location in a vehicle where
strong vibration, unstable, excessive of humidity and dust, and under direct
sunlight can be avoid. Also, avoid the area where the air bag inflates or any
other area where your safe driving is blocked.
Do not leave the Handheld Printer Terminal in vehicle for a long period of
time.
•
•
•
•

E-7
Lithium-ion Battery Pack
Danger
Never use the Handheld Printer Terminal and its option including the
battery pack and battery next to open flame, near a stove, or any other area
exposed to high heat, or leave them for a long period of time in a vehicle
parked in direct sunlight.
Never use the battery pack with any device other than the Handheld Printer
Terminal.
Never dispose of the battery pack by incinerating it or otherwise expose it
to heat.
Never transport or store the battery pack together with metal objects that
may result in shorting positive (+) and negative (–) terminals of the battery
pack. Be sure to place the battery pack in its case whenever transporting or
storing it.
Never throw the battery pack or otherwise subject it to strong impact.
Never pierce the battery pack with nails, hit it with a hammer, or step on it.
Use only the specified battery charger to charge the battery pack.
•
•
•
•
•
•
•
Warning
Never place the battery pack in a microwave oven or any other high-voltage
device.
If the amount of time period the battery pack can serve becomes
considerably short even after it has been fully charged for the specified time
period, stop using it.
Should the battery pack start to leak or emit a strange odor, immediately
move it away from any flame nearby. Leaking battery fluid is combustible.
Should fluid from the battery pack accidentally get into your eyes or on the
skin, do not rub it. Immediately rinse it off with clean tap water and then
consult a physician.
•
•
•
•
Caution
Danger of explosion if the battery pack is incorrectly replaced.
Replace only with same or equivalent type recommended by CASIO.
Dispose of used batteries according to the CASIO instruction.
Keep the battery pack out of the reach of small children.
•
•

E-8
Power Supply / AC Adaptor
Warning
Do not use the Handheld Printer Terminal at a voltage other than the
specified voltage. Also, do not connect the Handheld Printer Terminal to a
multi-plug power strip.
Never modify, sharply bend, twist, or pull on the power cord.
Never use a detergent to clean AC adaptor and its power cable, especially
on the plug and the jack.
When using the battery chargers and the cradles, be sure to use the
respective AC adaptors.
•
•
•
•
Caution
Never pull on the power cord when unplugging it. Always hold the plug
when unplugging it from the wall outlet.
Never touch the plug while your hands are wet.
Be sure to unplug the power cord from the wall outlet before cleaning the
battery chargers and the cradles.
Unplug the power cord from the wall outlet whenever leaving the battery
chargers and the cradles unattended for a long period.
The housing of the AC adaptor can become warm during normal use.
At least once a year, unplug the AC adaptor from the wall outlet and clean
any dust that builds up between the prongs of the plug.
Dust built up between the prongs can lead to the danger of fire.
•
•
•
•
•
•
Backup of All Important Data
Caution
Note that CASIO Computer Co., Ltd. shall not be held liable to you or any
third party for any damages or loss caused by deletion or corruption of data
due to use of the Handheld Printer Terminal, malfunction or repair of the
Handheld Printer Terminal or its peripherals, or due to the batteries going dead.
The Handheld Printer Terminal employs electronic memory to store data,
which means that memory contents can be corrupted or deleted if power is
interrupted due to the batteries going dead or incorrect battery replacement
procedures. Data cannot be recovered once it is lost or corrupted. Be sure
to make backup of all important data. One way to do this is to use the
separately sold cradles to transfer data to a computer.
•
•

E-9
Operating Precautions
Your Handheld Printer Terminal and its options are precision. Improper operation or
rough handling can cause problems with data storage and other problems. Note and
observe the following precautions to ensure proper operation.
Do not leave dead battery pack in the Handheld Printer Terminal for a long period.
Dead battery pack can leak, leading to malfunction and damage to the Handheld
Printer Terminal.
Stop or avoid using the Handheld Printer Terminal and its options in areas and
conditions subject to the following.
— Large amounts of static electricity
— Extreme heat or cold or humidity
— Sudden temperature change
— Large amount of dust
— After large amount of rain or water falls on the Handheld Printer Terminal
— Pressing the screen or keys with excessive force when using in the rain
Dead Pixels
The LCD panel employed in this product uses high precision and substantial number
of components which commonly cause a small number of the pixels not to light or
to remain lit all the time. This is due to the characteristics of LCD panel yield in
accuracy over 99.99% and permissible.
Water or other liquids on the power supply/data communication terminals
can lead to an electric shock or fire. Note also that soiling on the terminals
will impair the connection, leading to reduced charging and communications
functionality. As a safety precaution, disconnect the AC adaptor before cleaning
the power supply/data communication terminals with a dry cloth or cotton bud.
•
•
•
•

E-10
Lithium-ion Battery Pack
Each lithium-ion battery pack has its life. The life span heavily depends on how the
battery pack is charged or stored which may cause deterioration of the battery pack
to shorten the life span if it is handled improperly. Note the tips below to make the
battery pack last long.
— Be sure to charge the battery pack before using it if the battery pack is used for the
first time or if it has not been used for a long period of time.
— If the battery pack is repeatedly charged, the life span becomes short. To avoid the
repetition of charging the battery pack, be sure that the remaining capacity is low
before you start charging.
— Be sure to charge the battery pack in recommended temperature range. The
temperature range is dependant on device you use to charge including battery
chargers and Handheld Printer Terminals. Refer to the respective user guides.
Charging the battery pack in a temperature outside of the recommended range
causes deterioration.
— When used at low temperatures, the battery pack has a reduced capacity and will
supply power for shorter time.
The life span of the battery pack is also shortened.
— Charging the battery pack while the battery pack itself is freeze including inside
causes deterioration. Be sure to resume an ordinary room temperature on the
battery pack and then leave it unattended for approximately one hour before
charging.
— After charging the battery pack, if the performance of the battery pack does not
show any recovery, it is a sign of ending the life. Replace it with a new battery
pack.
— Avoid the battery pack with a full of the capacity to store for a long period of
time. If you need to store it for a long period, be sure that the remaining capacity
is 30 to 50 percent and to store in a moderate low temperature. This can reduce
deterioration.
— The battery pack gradually deteriorates over time. In particular, storing (or using)
the fully charged battery pack at high temperatures tends to accelerate battery pack
deterioration.
•

E-11
Important
This guide does not include any information about programming and download
procedures. See the applicable separate documentation for information about the
procedures.
After Service
Should this product ever malfunction, contact your original retailer providing
information about the product name, the date you purchased it, and details about the
problem.
This mark applies to EU countries and Turkey only.
•
•

E-12
Regulatory Information
The USA and Canada
GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THIS UNIT IN THE U.S.A. (not
applicable to other areas).
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC WARNING
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Proper connectors must be used for connection to host computer and/or peripherals in order to meet FCC
emission limits.
Caution Exposure to radio frequency radiation
To comply with FCC RF exposure compliance requirements, this device must not be co-located or
operating in conjunction with any other antenna or transmitter except in accordance with the FCC
multi-transmitter product procedures or as described in the filing.
•
•
•
•
Declaration of Conformity
Model Number: IT-9000E-MC25E, IT-9000E-C25E, HA-L60IO, HA-L62IO
Trade Name: CASIO
Responsible party: Industrial Handheld Division
Casio America, Inc.
Address: 570 Mt. Pleasant Avenue, Dover, New Jersey 07801, USA
Telephone number: 973-361-5400
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
For Users in Canada
These Class B digital apparatuses comply with Canadian ICES-003.
Cet appareil numériqué de la classes B est conformé à la norme NMB-003 du Canada.
These devices comply with RSS 210 of Industry Canada (IC).
Operation is subject to the following two conditions:
(1) These devices may not cause interference, and
(2) These devices must accept any interference, including interference that may cause undesired opera-
tion of this device.

E-13
L’ utilisation de ce dispositif est autorisée seulement aux conditions suivantes :
(1) il ne doit pas produire de brouillage et
(2) I’ utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce
brouillage est susceptible de compromettre le fonctionnement du dispositif.
Caution Exposure to radio frequency radiation
To comply with IC RF exposure compliance requirements, this device must not be co-located or
operating in conjunction with any other antenna or transmitter except in accordance with the IC multi-
transmitter product procedures or as described in the filing.
Précaution Exposition aux champs de radiofréquences
Pour respecter les normes relatives aux radiofréquences IC, ce dispositif ne doit pas être situé ou utilisé
à proximité d’une autre antenne ou d’un autre émetteur si ce n’est selon les procédures mentionnées
pour le multi-transmetteur IC ou décrites dans la documentation.
Europe
Products are for distribution within
all member states of the EU.
France limited to 2446.5-2483.5 MHz Indoor use.
Belgium limited to 2400-2483.5 MHz Indoor, 2460-2483.5 MHz Outdoor use.
0984
0984
Optional models HA-L60IO, HA-L62IO, HA-L30CHG, HA-G32DCHG and HA-G20BAT are
in conformity with the Council Directive 2004/108/EC.
Manufacturer:
CASIO COMPUTER CO., LTD.
6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan
Representative within the European Union:
CASIO EUROPE GmbH
Casio-Platz 1, 22848 Norderstedt, Germany

E-14
Checking in the Box
Please check the contents of the box before using the Handheld Printer Terminal for the
first time.
Open the box and make sure that all the items shown here are included.
Handheld Printer Terminal
Neck Strap and Stylus Holder
Stylus
Hand Strap
Roll Paper (80 mm)*
User's Guide (this manual)
Neck Strap Rings
Battery Pack
58 mm Paper Width Adjuster*
*Not included with IT-9000GM30E/GMC30E/GM35E.

E-15
Handheld Printer Terminal System Configuration
IT-9000 Series
IT-9000E-MC25E
IT-9000E-C25E
These models are
available in the
USA and Canada
only.
USB Cradle
HA-L60IO
Ethernet Cradle
HA-L62IO
Cradle-type Battery Charger
HA-L30CHG The illustration shows the
USB Cradle (HA-L60IO).
Car Mounted-type Battery Charger
HA-L35CHG
The car power cable accompanies
to HA-L35CHG.
Battery Pack
HA-G20BAT
Dual Battery Charger
HA-G32DCHG
Options
For the latest options list, refer to the ON-LINE manual available at
http://world.casio.com/system/pa/UsersGuide/sup85_e.html

E-16
Options
AC Adaptor
AD-S42120C-N5
AD-S42120B-N*
Screen Protect Sheet
HA-C90PS5B
USB Cable (to connect cradle to PC)
DT-380USB-A
Power Cord for Europe AC-CORD-EU
Power Cord for North America AC-CORD-US
Power Cord for Taiwan AC-CORD-TW
Power Cord for Korea AC-CORD-KR
Power Cord for Australia AC-CORD-AU
USB Cable (for client)
HA-L81USBC
USB Cable (for host)
HA-L80USBH
*The AD-S42120B-N is not sold in the EU or in EFTA member states.

E-17
General Guide
Shapes vary according to model.
Back
Bottom
Left RightFront
Top
17
17
16
12
13
10
29
1
2
3
7
8
4
5
6
9
10
14
11
15
18
28
27 19
21
24
22
23
20
26
19
25
19
25

E-18
1 Printer Prints when loaded with roll paper.
2 Splash Protect Cover A splash proof cover. Slide the cover open when printing.
3 Power Key Turns the power on and off.
4 Indicator 2 Flashes blue when operating via Bluetooth or orange when
operating via W-LAN. Lights red when there is a bar code
scanning error and lights green when a bar code scans
successfully.
Lights red when the alarm function is activated.
5 Indicator 1 Orange: Charging
Green: Charging complete
Red: Battery pack error or the surrounding temperature is out
of the charging temperature range.
6 Speaker Generates audio and buzzer tones.
7 Screen The screen displays texts, operations, indicators and so forth.
In addition, operations can be performed and data can be
input on the screen using stylus.
8 Keys* Used to enter numeric values and characters.
9 Magnetic Card
Reader
(IT-9000-GM30E/
GM35E/GMC25E/
GMC30E/IT-9000E-
MC25E only)
Used to read magnetic cards.
10 Printer Cover Lock
Switches
Used to lock the printer cover and to release.
11 R Program Key**
(for IT-9000-E/GE/
05E/05E-CN/G05E)
Used to perform bar code reading.
12 L Program Key**
(for IT-9000-E/GE/
05E/05E-CN/G05E)
Used to perform bar code reading.
13 SD Memory Card
Slot
SD card slot.
14 DC Jack The dedicated optional AC adaptor is connected to this jack.
15 USB Port USB device is connected to this port.
16 Barcode Reader
(IT-9000-20E/25E/
G20E/G25E/
GC25E/GMC25E/
GM30E/GMC30E/
GM35E/IT-9000E-
C25E/MC25E only)
Laser light or LED light is emitted from this window that
reads bar codes.