Casio 3288 User manual

Operation Guide 3288
E-9
To set the time and date
In the Timekeeping Mode, hold down1. Auntil the
seconds start to flash, which indicates the setting
screen.
Press2. Cto move the flashing in the sequence shown
below to select other settings.
Seconds MinutesHourDSTCity Code
Day 12/24-Hour FormatYearMonth
CCC
CCC
C
C
C
When the setting you want to change is flashing, use3. Dand Bto change it as
described below.
E-8
Timekeeping
Use the Timekeeping Mode to set and view the current
time and date.
Read this before you set the time and date !
The times displayed in the Timekeeping Mode and World
Time Mode are linked. Because of this, make sure you
select a city code for your Home City (the city where you
normally use the watch) before you set the time and date.
To view the current Home City code setting, pressxA
while in the Timekeeping Mode.
For full information on city codes, see the “City Codex
Table” at the back of this manual.
PM indicator
Day of week
Day
Seconds
Hour : Minutes
E-7
Stopwatch Mode Countdown Timer Mode Alarm Mode
E-6
General Guide
PressxCto change from mode to mode.
In any mode, pressxLto illuminate the display.
Timekeeping Mode World Time Mode
E-5
To illuminate the display....................................................................................... E-25
To specify the illumination duration.................................................................... E-25
To turn the button operation tone on and off ..................................................... E-26
E-4
Procedure Lookup
The following is a handy reference list of all the operational procedures contained in
this manual.
To set the time and date ......................................................................................... E-9
To toggle the Timekeeping Mode time between DST and Standard Time ....... E-12
To view the time in another city code.................................................................. E-13
To toggle a city code time
between Standard Time and Daylight Saving Time........................................ E-14
To measure times with the stopwatch................................................................. E-16
To use the countdown timer................................................................................. E-17
To set the countdown start time .......................................................................... E-18
To set an alarm time.............................................................................................. E-20
To test the alarm.................................................................................................... E-21
To turn an alarm on and off .................................................................................. E-22
To turn the Hourly Time Signal on and off.......................................................... E-23
E-3
Contents
General Guide.......................................................................................................... E-6
Timekeeping............................................................................................................. E-8
World Time............................................................................................................. E-13
Stopwatch .............................................................................................................. E-15
Countdown Timer.................................................................................................. E-17
Alarms .................................................................................................................... E-19
Illumination ............................................................................................................ E-24
Reference ............................................................................................................... E-26
Specifications ........................................................................................................ E-29
E-2
Note that the product illustrations in this manual are intended for reference only,x
and so the actual product may appear somewhat different than depicted by an
illustration.
E-1
About This Manual
Depending on the model of your watch, display textx
appears either as dark figures on a light background or
light figures on a dark background. All sample displays
in this manual are shown using dark figures on a light
background.
Button operations are indicated using the letters shownx
in the illustration.
Each section of this manual provides you with thex
information you need to perform operations in each
mode. Further details and technical information can be
found in the “Reference” section.
MA1106-EA

Operation Guide 3288
E-19
Alarms
You can set five independent Daily Alarms. When an
alarm is turned on, the alarm tone sounds when the alarm
time is reached. One of the alarms is a snooze alarm,
while the other four are one-time alarms.
You can turn on an Hourly Time Signal that causes the
watch to beep twice every hour on the hour.
There are six screens in the Alarm Mode. Four are forx
one-time alarms (indicated by numbers from
through ), one is for a snooze alarm (indicated by
), and one is for the Hourly Time Signal (indicated
by ).
All of the operations in this section are performed inx
the Alarm Mode, which you enter by pressing C(page
E-7).
Alarm number
Alarm time
(Hour : Minutes)
On/Off status
E-18
PressxDwhile a countdown operation is in progress to pause it. Press Dagain to
resume the countdown.
To completely stop a countdown operation, first pause it (by pressingxD), and then
press B. This returns the countdown time to its starting value.
To set the countdown start time
In the Countdown Timer Mode, hold down1. Auntil the
hours of the countdown start time start to flash, which
indicates the setting screen.
Press2. Cto move the flashing between the hours and
minutes.
While a setting is flashing, use3. D(+) or B(–) to
change it.
To set the starting value of the countdown time to 24x
hours, set .
Press4. Ato exit the setting screen.
E-17
Countdown Timer
The countdown timer can be set within a range of one
minute to 24 hours. An alarm sounds when the countdown
reaches zero.
The countdown operation continues even if you exit thex
Countdown Timer Mode.
All of the operations in this section are performed in thex
Countdown Timer Mode, which you enter by pressing C
(page E-7).
To use the countdown timer
Press Dwhile in the Countdown Timer Mode to start the countdown timer.
When the end of the countdown is reached, the alarm sounds for 10 seconds or untilx
you stop it by pressing any button. The countdown time is automatically reset to its
starting value after the alarm stops.
Minutes
SecondsHours
E-16
To measure times with the stopwatch
Elapsed Time
D D D D B
Start Stop Re-start Stop Clear
Split Time
D B B D B
Start Split
(SPL displayed)
Split release Stop Clear
Two Finishes
D B D B B
Start Split
First runner
finishes.
Display time of
first runner.
Stop
Second runner
finishes.
Split release
Display time of
second runner.
Clear
E-15
Stopwatch
The stopwatch lets you measure elapsed time, split
times, and two finishes.
The display range of the stopwatch is 59 minutes,x
59.99 seconds.
The stopwatch continues to run, restarting from zerox
after it reaches its limit, until you stop it.
The stopwatch measurement operation continues evenx
if you exit the Stopwatch Mode.
Exiting the Stopwatch Mode while a split time is frozenx
on the display clears the split time and returns to
elapsed time measurement.
All of the operations in this section are performed in the Stopwatch Mode, which youx
enter by pressing C(page E-7).
Seconds
1/100 second
Minutes
E-14
To toggle a city code time between Standard Time and Daylight Saving Time
In the World Time Mode, use1. Dand Bto display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
Hold down2. Afor about one second to toggle between
Daylight Saving Time (DST indicator displayed) and
Standard Time (DST indicator not displayed).
The DST indicator is on the display whenever you displayx
a city code for which Daylight Saving Time is turned on.
Note that the DST/Standard Time setting affects onlyx
the currently displayed city code. Other city codes are
not affected.
In the World Time Mode, you can switch the city code you currently have selectedx
as your Timekeeping Mode Home City between Standard Time and DST. The
setting you select in the World Time Mode will also be applied in the Timekeeping
Mode.
DST indicator
E-13
World Time
World Time shows the current time in 48 cities (29 time
zones) around the world.
All of the operations in this section are performed inx
the World Time Mode, which you enter by pressing C
(page E-6).
To view the time in another city code
In the World Time Mode, press D(eastward) and B
(westward) to scroll through the available city codes.
Holding down either button scrolls at high speed.
For full information about city codes, see the “City Codex
Table” at the back of this manual.
If the current time shown for a city is wrong, check yourx
Timekeeping Mode time and Home City code settings
and make the necessary changes.
City code
Current time in the zone of
the selected city code
E-12
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To toggle the Timekeeping Mode time between DST and Standard Time
In the Timekeeping Mode, hold down1. Auntil the
seconds start to flash, which indicates the setting
screen.
Press2. Ctwice to display the DST setting screen.
Press3. Dto toggle between Daylight Saving Time ( )
and Standard Time ( ).
Press4. Ato exit the setting screen.
ThexDST indicator is displayed on the Timekeeping Mode
and Alarm Mode screen while Daylight Saving Time is
turned on.
DST indicator
On/Off status
E-11
With the 12-hour format, thexP(PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
With the 24-hour format, times are displayed in the range of 0:00 to 23:59, withoutx
any indicator.
The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode isx
applied in all modes.
The year can be set in the range of 2000 to 2099.x
The watch’s built-in full automatic calendar makes allowances for different monthx
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
The day of the week is automatically displayed in accordance with the date (year,x
month, and day) settings.
E-10
Screen To do this: Do this:
Reset the seconds to Press D.
Change the city code Use D(east) and B(west).
Toggle between Daylight Saving Time ( ) and
Standard Time ( ) Press D.
Change the hour or minutes Use D(+) and B(–).
Toggle between 12-hour ( ) and 24-hour
( ) timekeeping Press D.
Change the year, month, or day Use D(+) and B(–).
See “Daylight Saving Time (DST)” (page E-12) for details about the DST setting.x
Press4. Ato exit the setting screen.
Resetting the seconds toxwhile the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to without changing the minutes.

Operation Guide 3288
E-29
Specifications
Accuracy at normal temperature: ±30 seconds a month
Timekeeping: Hour, minutes, seconds, a.m./p.m. (P), day, day of the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City code (can be assigned one of 48 city codes); Daylight Saving
Time (summer time)/Standard Time
World Time: 48 cities (29 time zones)
Other: Daylight Saving Time/Standard Time
Stopwatch
Measuring unit: 1/100 second
Measuring capacity: 59'59.99"
Measuring modes: Elapsed time, split time, two finishes
Countdown Timer
Measuring unit: 1 second
Input range: 1 minute to 24 hours (1-minute increments and 1-hour increments)
E-28
Initial Screens
When you enter the World Time or Alarm Mode, the data you were viewing when you
last exited the mode appears first.
World Time
The seconds count of the World Time is synchronized with the seconds count of thex
Timekeeping Mode.
All World Time Mode times are calculated from the current Home City time in thex
Timekeeping Mode using UTC time differential values.
The UTC differential is a value that indicates the time difference between ax
reference point in Greenwich, England and the time zone where a city is located.
The letters “UTC” is the abbreviation for “Coordinated Universal Time”, which is thex
world-wide scientific standard of timekeeping. It is based upon carefully maintained
atomic (cesium) clocks that keep time accurately to within microseconds. Leap
seconds are added or subtracted as necessary to keep UTC in sync with the Earth’s
rotation.
E-27
Holding downxCto turn the button operation tone on or off also causes the watch’s
current mode to change.
The MUTE indicator is displayed in all modes when the button operation tone isx
turned off.
Auto Return Features
If you leave the watch in the Alarm Mode for two or three minutes without performingx
any operation, it automatically changes to the Timekeeping Mode.
If you leave a screen with flashing digits or a cursor on the display for two or threex
minutes without performing any operation, the watch automatically saves any
settings you have made up to that point and exits the setting screen.
Scrolling
The Band Dbuttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls at high speed.
E-26
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Button Operation Tone
MUTE indicator The button operation tone sounds any time you press one
of the watch’s buttons. You can turn the button operation
tone on or off as desired.
Even if you turn off the button operation tone, the alarm,x
Hourly Time Signal, and Countdown Timer Mode alarm
all operate normally.
To turn the button operation tone on and off
In any mode (except when a setting screen is on the
display), hold down Cto toggle the button operation tone
on (MUTE indicator not displayed) and off (MUTE indicator
displayed).
E-25
To illuminate the display
In any mode, press Lto turn on illumination.
You can use the procedure below to select either 1.5 seconds or 3 seconds as thex
illumination duration. When you press L, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current illumination duration setting.
To specify the illumination duration
In the Timekeeping Mode, hold down1. Auntil the
seconds start to flash, which indicates the setting
screen.
While the seconds are flashing, press2. Bto toggle the
illumination duration between 1.5 seconds ( ) and
3 seconds ( ).
Press3. Ato exit the setting screen.
E-24
Illumination
This watch has an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark.
Illumination Precautions
The electro-luminescent panel that provides illuminationx
loses power after very long use.
Illumination may be hard to see when viewed under directx
sunlight.
The watch may emit an audible sound whenever thex
display is illuminated. This is due to vibration of the
EL panel used for illumination, and does not indicate
malfunction.
Illumination automatically turns off whenever an alarmx
sounds.
Frequent use of illumination runs down the battery.x
E-23
To turn the Hourly Time Signal on and off
Hourly time signal
on indicator
On/Off status
In the Alarm Mode, use1. Dand Bto select the Hourly
Time Signal ( ).
Press2. Ato toggle it on ( displayed) and off
(displayed).
The Hourly Time Signal on indicator is shown on thex
display in all modes while the Hourly Time Signal is
turned on.
E-22
To turn an alarm on and off
Alarm on
indicator
Snooze alarm indicator
On/Off status
In the Alarm Mode, use1. Dand Bto select an alarm.
Press2. Ato toggle it on ( displayed) and off
(displayed).
Turning on a one-time alarm (xthrough )
displays the alarm on indicator on its Alarm Mode screen.
Turning on the snooze alarm (x) displays the alarm
on indicator and snooze alarm indicator on the Alarm
Mode snooze alarm screen.
In all modes, the alarm on indicator is shown for anyx
alarm that is currently turned on.
The alarm on indicator flashes while the alarm isx
sounding.
The snooze alarm indicator flashes during the 5-minutex
intervals between alarms.
E-21
Press3. Cto move the flashing between the hour and minute settings.
While a setting is flashing, use4. D(+) and B(–) to change it.
When setting the alarm time using the 12-hour format, take care to set the timex
correctly as a.m. (indicator not displayed) or p.m. (Pindicator).
Press5. Ato exit the setting screen.
Alarm Operation
The alarm sounds at the preset time for about 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, or until you turn the alarm off (page E-22).
To stop the alarm tone after it starts to sound, press any button.x
Performing any one of the following operations during a 5-minute interval betweenx
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen (page E-9)
Displaying the snooze alarm setting screen (page E-20)
To test the alarm
In the Alarm Mode, hold down Dto sound the alarm.
E-20
To set an alarm time
In the Alarm Mode, use1. Dand Bto scroll through the
alarm screens until the one whose time you want to set
is displayed.
BD
BB
BB
DB
DD
DD
To set a one-time alarm, display one of the screens indicated by an alarm numberx
from through . To set the snooze alarm, display the screen
indicated by .
The snooze alarm repeats every five minutes.x
After you select an alarm, hold down2. Auntil the hour setting of the alarm time
starts to flash, which indicates the setting screen.
This operation turns on the alarm automatically.x

Operation Guide 3288
L-3
City
Code City UTC Offset/ GMT Differential
DXB Dubai +4
KBL Kabul +4.5
KHI Karachi +5
MLE Male
DEL Delhi +5.5
DAC Dhaka +6
RGN Yangon +6.5
BKK Bangkok +7
SIN Singapore
+8HKG Hong Kong
BJS Beijing
SEL Seoul +9
TYO Tokyo
ADL Adelaide +9.5
GUM Guam +10
SYD Sydney
City
Code City UTC Offset/ GMT Differential
NOU Noumea +11
WLG Wellington +12
xBased on data as of December 2010.
xThe rules governing global times
(UTC offset and GMT differential) and
summer time are determined by each
individual country.
In December 2007, Venezuela*
changed its offset from –4 to –4.5.
Note, however, that this watch displays
an offset of –4 (the old offset) for the
CCS (Caracas, Venezuela) city code.
L-2
City Code Table
City
Code City UTC Offset/ GMT Differential
PPG Pago Pago –11
HNL Honolulu –10
ANC Anchorage –9
YVR Vancouver
–8SFO San Francisco
LAX Los Angeles
DEN Denver –7
MEX Mexico City –6
CHI Chicago
MIA Miami –5
NYC New York
CCS* Caracas –4
YYT St. Johns –3.5
RIO Rio De Janeiro –3
RAI Praia –1
City
Code City UTC Offset/ GMT Differential
LIS Lisbon 0
LON London
BCN Barcelona
+1
PAR Paris
MIL Milan
ROM Rome
BER Berlin
ATH Athens
+2
JNB Johannesburg
IST Istanbul
CAI Cairo
JRS Jerusalem
MOW Moscow +3
JED Jeddah
THR Tehran +3.5
L-1
City Code Table
E-30
Alarms: 5 daily alarms (4 one-time alarms: 1 snooze alarm); Hourly Time Signal
Illumination: EL Backlight (electro-luminescent panel); Selectable illumination
duration
Other: Button operation tone on/off
Battery: One lithium battery (Type: CR1616)
Approximately 3 years on type CR1616 (assuming alarm operation 10 seconds per
day, and one illumination operation 1.5 seconds per day)