Casit KEQS08 User manual

KEQS08
KEQS08-R_211221_VXX02_GB
• Single-phase control unit for 1 motor 230Vac
• For sliding gates or swing gate with 1 motor, roll-up doors, rolling shutters with
electrical lock and encoder option
• 433.92 Radio receiver integrated with obstacle detection
Radio receiver
-1-
-2-
-3-
-4-
-5-
-6-
-7-
-8-
-9-
-10-
-11-
-12-
-13-
-14-
-15-
-16-
-17-
-18-
-19-
230 Vac
230 Vac
Lamp
Lamp
MOT common
MOT close
MOT open
+ Antenna Signal
Common contacts
Common contacts
+ 12 Vdc
STOP
PHOTO 1
LSO
LSC
START
PEDESTRIAN
24 Vac
24 Vac / + 24Vdc
MOP
CL
COM
OUT
TX
-22-
-23-
Electrical lock
12 Vac
-24-
-25-
Dry Contact
Dry Contact
N.C.
Photocells working
in closing
See par. 2.10-2.11
Lamp or courtesy light
230Vac
C
100%
ITALY
N.C. N.C. N.O N.O.
RX
-20-
-21-
-24Vdc, COM serv. & sec.
PHOTO 2
-26-
-28-
+ 5V encoder
- 5V encoder
-27-
Encoder Signal
12 Vac Electrical lock
(in case of 24Vac connect to the terminal
board no.22 and 18)
For a correct use of the encoder,
we recommend to ready the manual.
!
Radio receiver
OUT
TX
Photocell working in closing
and in opening
RX

KEQS08 Technical Manual
-2-
Foreword
This manual provides all the specifi c information you
need to familiarize yourself with and correctly opera-
te your unit. Read it very carefully when you purchase
the instrument and consult it whenever you have doubts
regarding use and before performing any maintenance
operations. The factory has the right to modify the pro-
duct without previous notice.
Environmental protection
measures
Information regarding the environment for cus-
tomers within the European Union. European
Directive EC 2002/96 requires that units bearing
this symbol on the unit and/or on the packaging
be disposed of separately from undiff erentiated
urban wastes.
The symbol indicates that the product must not be dis-
posed of with the normal household wastes. The owner is
responsible for disposing of this product and other elec-
trical and electronic equipment through specifi c waste
collection facilities indicated by the government or local
public agencies. Correct disposal and recycling help pre-
vent any potentially negative impact on the environment
and human health. To receive more detailed information
regarding disposal of your unit, we recommend that you
contact the competent public agencies, the waste collec-
tion.
Index
Par. Description Pag
1 Introduction 3
1.1 Safety precautions
1.2 Field of application
1.3 Type of installation
1.4 Technical features
2 Technical description 4
2.1 Diagram of the control unit and electrical connections
2.2 Description of the electrical connection 5
2.3 Connection of the FLASHING LIGHT 230 Vac 6
2.4 Connection of one 24V gate open and light for moving
2.5 Connection of the COURTESY light
2.6 Power supply of the ACCESSORIES
2.7 Connection of the STOP and PHOTO 2 7
2.8 Connection of LIMIT SWITCHES LSO and LSC
2.9 Connection of the MAGNETIC LIMIT SWITCHES
2.10 Connection of the 24 Vac photocell 8
2.11 Connection of the 24 Vdc photocell
2.12 Connection of a 3 wire 24Vdc Photocell 9
2.13 Connection of 12/24V electrical lock
2.14 Connection of START command and PARTIAL OPEN-
ING (Pedestrian)
2.15 Checking connections 10
3 Functions and adjustments
3.1 Use of the DIP B
3.2 Use of the DIP A 11
3.3 JP1 function: “Death man” function
4 Managing of the remote controls 12
4.1 FULL CANCELLATION of the memory
4.2 ROLLING CODE activation/deactivation
4.3 Learning of the remote controls 13
5 Reset of the memory at factory settings
6 Working Time Learning 14
6.1 Time learning: STANDARD WAY
6.2 Time learning PARTIAL OPENING 15
6.3 Time learning: pause (easy way)
6.4 Time learning: ADVANCED WAY 16
7 TEST operating guide 17
8 Adjustment of the Trimmers
9 CE Declaration of Conformity 18
DANGEROUS
This is a warning and if it is not respec
it can provoque material damage.
DEVICE UNDER TENSION
The installation should be done only
from professional installer.
READ CAREFULLY THE
OPERATING MANUAL
Read carefully this manul before in-
stallation and keep it for the future.
Symbols and warning

KEQS08 Technical Manual
-3-
Using the unit improperly and performing repairs or modifi cations personally will void the warranty. The producer
declines any responsibility for damages due to inappropriate use of the product and due to any use other than the
use the product was designed for. The producer declines any responsibility for consequential damages except civil
liability for the products.
Every programming and/or every maintenance service should be done by qualifi ed technicians.
1.1 Safety precautions
1 Introduction
1.3 Type of installation
These two simple diagrams show only one of the possible applications for this control unit. The risks inherent to
the “MACHINE” and the user’s requirements must be analyzed in depth in order to establish how many elements
need to be installed. All photocells have a system of synchronism that makes it possible to eliminate interference
between two pairs of photocells (for other details, see the instructions for the photocells). In the diagram, the pair of
photocells “Photo A” (considered in this control unit) has no eff ect during opening while it causes a total inversion
during closing. “Photo A2” is connected in series to “Photo A”.
Installation for sliding gates Installations for swing gates
FOTO A
FOTO A2
We recommend to install a STOP switch which stops immediatelly the gate.
The switch has a normally close contact which opens the contact when it is
working. See Par. 2.7
The KEQS08 electronic control unit is used to control the movement of entrances, swinging gateways, rolling
gates and automatic doors. It can be connected to a hydraulic or electromechanical actuator equipped with an
asynchronous, single-phase motor operating at a voltage of 230 Vac.
1.2 Field of application
Dimensions 87 x 150 x 45 mm
Weight 0.6 Kg
MAX power of single motor 1
750
4
HP
W
A
MAX power of signal light 230 Vac 40 W
MAX consumption for dry 2 A
MAX consumption 24 Vac/dc 300 mA
MAX consumption 12 Vdc 50 mA
MAX consumption 12 Vac 1 A
1.4 Technical description
FOTO A
FOTO A2

-4-
1 2 Control unit power supply 230Vac
3 7 Power supply for 230Vac motor and for
230Vac Signal Light
8 21 Power supply for accessories and inputs and
securities
22 23 Electrical lock,
Power supply of the accessories
24 25 “Dry” contacts for light or photocell TEST
or signal light without fl ashing control card
26 28 Connection of the encoder
JUMPER
AC/DC
Selection of the power supply,
24 Vac output or dc on terminals 18-19-20
JUMPER
JP1 “Death man” function (Par. 3.3)
DIP A Set up of the logic of the control unit
DIP B Exclusion of the inputs,
activation of Soft-start (gradual start)
Button PManaging of the remote controlsd, force
adjustment, increase of the pause time
2.1 Diagram of the control unit and electrical connections
2 Installation
Connection of the POWER SUPPLY
LINE 230 Volt Single-phase alternate cur-
rent. The control unit power supply line
must always be protected with a magnetic-
thermal switch or a pair of 5A fuses.
An earth leakage circuit breaker is recom-
mended but not necessary if already avai-
lable in the site if one is already installed
on the plant.
Connection of the MOTOR
Pay attention not to invert
the OPEN and CLOSE poles.
When in doubt as to the correct connection, if
possible, manually position the automation at the
midpoint of its stroke. Be ready to stop the system
using the STOP control!
To be sure that the opening is really “opening”, try
to block the photocells: if the gate begins to close,
the connection is incorrect and the motor OPEN
and CLOSE wires must be inverted.
KEQS08 Technical Manual
20
40
60
80
100
0
2
4
6
8
10
MAX
MIN
2
4
6
8
10
OFF
ON
123 45678910
KE
ON
123 4
KE
567 8
FORZA
TEMPI
CODICI
L1
L2
V.RALLBLOCK
8 9 10 11 12 13 14 15 16 17 18 19 20 21
1 2 3 4 5 6 7
24 25
22 23 26 27 28
F1 - 160mA
F2 - 4A
JP1
DIP A
DIP B
AC / DC

230 Vac 1 Electrical power supply 230 Vac 50 Hz
230 Vac 2 Electrical power supply 230 Vac 50 Hz
Signal Light 3Output for 230 Vac signal
or courtesy light maximum power 40W
4
MOT common 5 Output for connection of COMMON motor pole
MOT close 6 Output for connection of CLOSING motor pole
MOT open 7 Output for connection of OPENING motor pole
+ Antenna 8 Input for antenna signal
Common 9 Common for all inputs:
services, safety devices, coaxial cable, 12 Vdc
Common 10
+ 12Vdc 11 Output +12 Vdc maximum current 50mA (positive)
Stop 12 STOP input
PHOTO 1 13 Input for photocell 1 (intervention only when closing)
Lso 14 Input for opening limit switch
Lsc 15 Input for closing limit switch
Start 16 Input for bistable START
Pedestrian 17 Input for bistable partial PEDESTRIAN opening
(same setting as START)
24Vac 18 Output 24Vac (See Par. 2.10 & 2.11)
+ 24Vdc / 24Vac 19 Output + 24Vac/dc (See Par. 2.10 & 2.11)
- 24Vdc 20 Output - 24Vdc (See Par. 2.10 & 2.11)
PHOTO 2 21 Input for photocell 2 (intervention in opening and closing) DIP6A
Electrical lock 22 0 Vac Electrical lock (See Par. 2.13)
12 Vac 23 Out 12 Vac Electrical lock
Dry contact 24 “Dry” contacts for light or photocell TEST
or fl ashing light without intermittence circuit board
Dry contact 25
+5 Vdc 26 power supply of the Encoder
Signal for encoder 27 Signal for encoder
-5 Vdc 28 power supply of the Encoder
-5-
2.2 Description of the electrical connection
KEQS08 Technical Manual

-6-
2.3 Connection of the 230 Vac SIGNAL LIGHT
Signal light
with fl ashing control card
Signal Light without fl ashing control card
DIP 4 - OFF
ON
2
143 5
If you use the photocells test,
or a 24V light, this connection cannot be used.
!
2.4 Connection of one 24V LIGHT for open or moving gate
If you use the photocells test,
or a 24V light, this connection cannot be used.
!
2.5 Connection of the COURTESY light
LIGHT
230 Vac
DIP 4 - ON
2.6 Power supply of the ACCESSORIES
18 19 20 21 24 25
3 4 5 3 4 5 24 25
KEQS08 Technical Manual
Terminal board 10 (-) / 11 (+)
Voltage: 12 Vdc
Maximum current: 50 mA
Put JUMPER
JAC/DC as shown
in the picture
Terminal board 19 (+) / 20 (-)
Voltage: 24 Vdc
Max current: 300 mA
8 9 10 11 12 13 14 15 16 17 18 19
Terminal board 18 / 19
Voltage: 24 Vac
Max current: 300 mA
Put JUMPER
JAC/DC as shown
in the picture
+
-
-
+
!!
AC DC
ON
2
143 6 587 10 9
Terminals 3 and 4 are powered when the gate is
opening up to 2 min. after gate closing
1 2 3 4 5 6 7
20 21
AC DC

-7-
2.7 Connection of the STOP and PHOTO 2
Connection of the safety devices requires the use of
any push-button or N.C. (normally closed) contact.
If more devices are available, connect in parallel.
2.8 Connection of LIMIT SWITCHES LSO and LSC
The picture shows the connection of both limit
switches, however, on this control unit they can be
used separately. The limit switch contacts must be
N.C. (normally closed) contacts.
If the LSO or LSC
inputs aren’t used:
put the ON DIP3B for LSO
put the ON DIP4B for LSC
!
2.9 Connection of the MAGNETIC LIMIT SWITCHES
JUMPER AC/DC
Power Supply
magnetic limit
switches
24 Vdc
Bring the
Jumper in DC
8 9 10 11 12 13 14 15 16 17 18 19
8 9 10 11 12 13 14 15 16 17 18 19
OPEN
N.C.
CLOSE
N.C.
LIMIT
SWITCHES
OPEN
N.C.
CLOSE
N.C.
LIMIT
SWITCHES
KEQS08 Technical Manual
8 9 10 11 12 13
Connection of the STOP control
Push-button: stops and temporarily prevents all
control unit function until it is pressed again.
Switch: keeps the automation blocked until the
swicht will be activated again.
If the STOP input
is NOT used put
the DIP 1B on
ON. If the input
PHOTO 2 is not
used, put the DIP
5B on ON.
!
20 21
20 21
Connection of the PHOTO2 control:
For operation see DIP 6 A page. 11
RX
TX
Contact NC
8 9 10 11 12 13 14 15 16 17 18 19
24 Vac
AC DC
Set the
JUMPER
JAC/DC
as in the
picture
20 21

-8-
The photocell receiver
contact must be:
- dry (isolated from
power supply voltages)
- type N.C.
(Normally closed)
If more photocells are
available, connect them
in parallel, they must be
connected in series.
The photocell TEST ensures the gate is working when the photocells are functioning
properly. In fact, the control unit performs the test before each opening. if the photocells
are not working properly, the signal light will be lit on for 5 seconds and the gate stops.
The control unit automatically activates the test only after the START command
times have been learnt. If you wish to return to the LIGHT function on terminals
24 and 25, the photocells must be connected without the test and then you must
repeat the times learning operation with the START command.
The TEST function is compatible with slow response devices (for example TRANSCEI-
VER) so the gate be slowly while opening. The TEST can be done also from some
devices in the INPUT COSTA (safety edge) and STOP. After the TEST connections,
memorize the working time for the START control during this time the control unit check
the devices which are under TEST.
KEQS08 Technical Manual
2.10 Connection of the 24 Vac photocell 1 only closing
2.11 Connection of the 24 Vdc photocell 1
If the STOP input is
NOT used put the
DIP 2B in ON.
!
RX TX
NC Contact
TX
24 25
Without TEST With TEST
8 9 10 11 12 13 14 15 16 17 18 19
24 Vac
RX
NC Contact
8 9 10 11 12 13 14 15 16 17 18 19
24 Vac
AC DC
Put
JUMPER
JAC/DC
as shown in
the picture
RX TX
NC Contact
TX
24 25
Without TEST With TEST
8 9 10 11 12 13 14 15 16 17 18 19
24 Vdc
8 9 10 11 12 13 14 15 16 17 18 19
+
-
RX
NC Contact
24 Vdc +
-
Put
JUMPER
JAC/DC
as shown in
the picture
AC DC
20 21 20 21
20 21 20 21

-9-
2.14 Connection of the “START” and “PEDESTRIAN” commands
The PEDESTRIAN opening command can be connected to any push
button or N.O. (normally open) contact. If several devices are used,
they must be connected in parallel.
Using terminals 9 and 16 it is possible connect a TIMER to program
gate opening. The timer contact must be an NO (normally open) con-
tact and must remain closed while the gate remains open.
If an opening command is connected to terminal 16, it must be con-
nected in parallel.
The START opening command can be connected to
any push-button or N.O. (normally open) contact.
2.12 Connect the 3 WIRES PHOTO 1 24 Vdc
POWER SUPPLY
TX PHOTOCELL
POWER SUPPLY
RX PHOTOCELL +
-
+
-
Photocell receiver.
N.C. contact terminals
-+
Bring JUMPER AC/DC
as shown in the picture
Voltage: 24 Vdc
Maximum current: 300 mA
8 9 10 11 12 13 14 15 16 17 18 19
8 9 10 11 12 13 14 15 16 17 18 19
KEQS08 Technical Manual
20 21
20 21
Here you can see the connections
of the electrical lock: 12 Vac
2.13 Electrical lock connection: 12 or 24 Vac
22 23 Here you can see the connections
of the electrical lock: 24 Vac
Put JAC/DC as shown in the picture:
22 23
17 18 19 20 21
AC DC
START
PEDESTRIAN

-10-
3 Functions and adjustments of DIP SWITCHES
KEQS08 Technical Manual
3.1 Use of the DIP B
The control board has several micro-switches to activate a lot of functions in order to fi nd suitable solutions for the
user and to make the installation more safe.
1-ON STOP
12 Exclude the input STOP
2-ON PHOTO
13 Exclude the input PHOTO 1
3-ON LSO
14 Exclude the input LSO
4-ON LSC
15 Exclude the input LSC
5-ON Safety edge 8K2
21 Exclude the input PHOTO 2
6-ON Soft-Start The gate is opening with a gradual speed
7-ON Industrial use
The Partial Opening became a CLOSE COMMAND while
the START command is OPEN COMMAND.
DIP1A OFF and DIP2A ON -> it doesn’t close automatically
DIP1A ON and DIP2A ON -> it close automatically
8-ON -Not used
ON
2
143 6 587
ON
2
143 6 587
ON
2
143 6 587
ON
2
143 6 587
ON
2
143 6 587
ON
2
143 6 587
ON
2
143 6 587
ON
2
143 6 587
LED L1 indicates the correct working of the control unit. It fl ashes each second to indicate the micro-processor is
activated and waiting for commands. If it fl ashes softly it means that the input SAFETY EDGE is not in the standard
mode.
When the control unit is powered, the warning lights, set on the inputs, are ON when the contacts on the inputs are
closed toward the common:
Normally the red lights on inputs STOP - PHOTO - LSO - LSC are ON
Normally the green lights on the control inputs START - PEDESTRIAN are OFF
STOP PHOTO LSO LSC START PED
L1
2.15 Checking connections
L2: not used

-11-
KEQS08 Technical Manual
3.3 JP1 function: “Death man” function
JP1
close
“Death man”
function
The command START open, the PARTIAL OPENING closes.
Motors stops immediatelly when the button will be released
3.2 Use of the DIP A
1-OFF
2-OFF Automatic 1 It inverts: open and close. It closes automatically at the end of the pause time
1-ON
2-OFF Condominium In opening and pause time doesn’t accept commands. it re-closes automatically at the end of the pause time.
1-OFF
2-ON Semi automatic By every command open-stop-close-stop-open etc. It doesn’t re-close automatically
1-ON
2-ON Automatic 2
By every command
open-stop-close-stop-open etc.
It recloses automatically at the end of the pause time.
3-ON Reversing
Stroke It allows the electrical lock to be released
4-ON Courtesy
light
Terminals 3 and 4 are powered when the gate is opening
until 2 minutes after closing,useful incase the courtesy light
needs to be powered
5-ON Pre-lighting ON: Pre-lighting 4 seconds
OFF: Pre-lighting deactivated
6Photo 2
ON: In opening and closing it stops and reverses the motion
for 2s after 1 minute it closes again.
OFF: During opening and closing, it stops and reopens
with the obstacle removed (folding door function), re-closes
after pause time.
7Motor starting
3 sec after LSC
ON: The motor runs for 3 seconds
OFF: The motor runs until LSC activation
8-ON Phototest
Activates the TEST in the inputs PHOTO, STOP and
SAFETY EDGE (COSTA) (when a TRANSCEIVER is
availalbe, see Chap no. 7)
9-ON
Logic of the
obstacle
detection: (A)
In closing, it reverses the direction of travel up to FCA,
pauses for 1 minute and then closes again. With a new
START command it closes after pause time. In opening
it reverses to close for 2 seconds, after one minute it
closes completely. If you give a command START the gate
reopens.
9-OFF
Logic of the
obstacle
detection: (B)
Works as limit switch
10-ON
Programming
time, advanced
system
It activate the advanced working time
ON CTS
2
143 6 587 10 9
ON CTS
2
143 6 587 10 9
ON CTS
2
143 6 587 10 9
ON CTS
2
143 6 587 10 9
ON CTS
2
143 6 587 10 9
ON CTS
2
143 6 587 10 9
ON CTS
2
143 6 587 10 9
ON CTS
2
143 6 587 10 9
ON CTS
2
143 6 587 10 9
ON CTS
2
143 6 587 10 9
ON CTS
2
143 6 587 10 9
ON CTS
2
143 6 587 10 9
ON CTS
2
143 6 587 10 9

-12-
KEQS08 Technical Manual
4 Using the remote controls
This receiver can manage standard codes from 12 till 64 bit and rolling codes HCS©. The fi rst learned transmitter
establish the code’s type that the receiver has to manage, it means that the transmitter has to have the same code’s
type. Concerning the rolling codes it is possible to activate or disactivate the key’scontrol and the rolling counter.
With this function you can choose the security level of the receiver.
This operation cancels all codes in the memory. You cannot cancel of a single remote control code. It is necessary
to reset the memory before learning new remote controls. The cancellation of the memory (all codes) is possible
only when the gate is closed.
> 1 Make sure that the gate is CLOSED
Press and keep pressed the CODICI BUTTON
> 2 Wait until LED L1 start fl ashing, then release it.
Wait the reset of the memory.
4.1 FULL CANCELLATION of the memory
CODICI
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
CODICI
4.2 ROLLING CODE ACTIVATION OR DEACTIVATION
Fixed code MODE (L1 - one fl ash)
The receiver manages standard codes from 12 to 64 bit and HCS© rolling code (only the fi xed part)
Rolling code MODE (L1 - fl ashes twice):
You can control the rolling code counter and the remote cannot be duplicated
> 1Press and release the button CODICI, LED L1 will lit on.
Wait until the memory has been cancelled.
> 2Press and release the button CODICI again, LED L1 fl ashes and lit on
> 3Press the button CODICI again, LED L1 fl ashes twice,
it activate the rolling code counter.
4To return to the fi xed code mode,
repeat the operation from point no.1 in this way LED L1 will fl ash only once.
CODICI
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
CODICI
CODICI
>
>
>
>
>
>
>
>
>
>
>
>
>
>
L1
L1
L1
L1
L1

-13-
KEQS08 Technical Manual
4.3 Learning of the remote controls
The remote controls can be learnt ONLY when the gate is CLOSED.
CONNECT THE ANTENNA CABLE AFTER MEMORIZATION OF THE REMOTE CONTROLS (terminals 8-9)
- If you need to learn a new remote control repeat the same operation.
- When you push the remote control’s button and the L.E.D. codes is switched ON, it means that the remote control is not compatible
- When you push the remote control’s button and the L.E.D. codes fl ashes slowly, it means that the memory is FULL.
- It is not possible to cancel a single code
1Make sure that the gate is CLOSED
> 2Press and release the CODICI button, the LED L1 will stay lit ON.
3Press the button of the remote control, ex: button no.1:
if it is memorized LED L1 will fl ash
> 1Press and release the CODICI button, the LED L1 will lit ON.
> 2Press again the CODICI button, the LED L1 will fl ash and lit ON
3Press the button of the remote control, ex:
button no.2: if it is memorized LED L1 will fl ash
CODICI
CODICI
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
CODICI
START
PEDESTRIAN
The reset of the control unti set all parameters at factory settings. It doesn’t cancel the remote controls codes, there
are two diff erent memories available:
1Press the buttons CODICI and TEMPI
LED L1 lit ON
2Wait 10 seconds until LED L1 will switch OFF
3Release the buttons CODICI and TEMPI
TEMPI CODICI
TEMPI CODICI
5 Reset of the memory at factory settings
L1
L1
L1
L1
L1
L1
L1

-14-
KEQS08 Technical Manual
1
The gate is in closed position
set the control board in Semiautomatic mode
(DIP 1A OFF - DIP 2A ON - DIP 7B OFF)
2Put in OFF the switch no. 10 of the DIP A
3Push the button TEMPI *
The motor OPENS
4
Wait that the fi rst leaf is open,
if the limit switches are available read from point no. 6
otherwise press the button TEMPI to stop the fi rst leaf.
5
When motor stops,
let the time leave until the gate should be opened
(pause time)
6 > Press the button TEMPI (times) to close.
First leaf starts opening
7Wait the gate is closed,
Working time memorization completed
>
ON CTS
2
143 6 587 10 9
* When you press button TEMPI for the fi rst time you can use a START command from terminal no.16 or from a
remote control
6 Time learning
6.1 Time learning: STANDARD WAY
TEMPI
STOP
TEMPI
>
>
>
>
>
>
>
>
>
>
>
>
>
>
>
IF YOU DON’T USE AN ENCODER:
SET THE SPEED WITH THE TRIMMERS
!

The gate is in closed position
1
Press and keep pressed the TIMES button till the
control board starts motor in OPEN,
then release the TEMPI button
Motor OPENS
2Press the TEMPI button Motor STOPS
Let the pause time run for the PARTIAL OPENING
3Press the TEMPI button Motor CLOSES
4Push the button TEMPI
(if the closing limit switches is not available)
Motor stops. The door is closed.
Operation completed
4 a ... If the limit switch is available wait until the
motor (partial opening use) stops
Motor stops by closing limit
switches. The door is closed.
Operation completed
6.2 Time learning PARTIAL OPENING
TEMPI
TEMPI
TEMPI
TEMPI
-15-
KEQS08 Technical Manual
6.3 Time learning: pause (easy way)
The gate is in PAUSE
1Press and release the TEMPI button The L.E.D. lights for opening and
closing are LIT ON
Let the new pause time run…
2Press and release the TEMPI button The gate CLOSES.
Time learning completed
TEMPI
TEMPI

-16-
KEQS08 Technical Manual
The gate is in closed position
set the control board in Semiautomatic mode
(DIP 1A OFF - DIP 2A ON - DIP 7B OFF)
1Put in ON the DIP 10A Gate is closed
2 * Push the button TEMPI The motor OPENS
3
Push the button TEMPI (or START)
... If the slowing down is activated...
trimmer V RALL
The motor opens slowly
4
Push the TEMPI button (or START)
(if the opening limit switches is not
available).
Motor stops, starts the pause time
5... If the limit switch is available
wait until the motor stops
motor stops, the counting
of the pause time starts
Let the pause time run…
7Push the TEMPI button (or START) The motor CLOSES
8
Push the TEMPI button (or START)
if the slowing down is activated
(trimmer see V.RALL)
The motor closes slowly
9
Push the button TIMES (or START)
... if the closing limit switches no.1 is not
available...
Motor stops. Advanced learning
time completed
10 ... if the limit switches is available wait
motor stops
Motor stops. Advanced learning
time completed
ON
CTS
2
143 6 587 10 9
>
6.4 Time learning: ADVANCED SYSTEM
>
TEMPI
TEMPI
RALL.
>
TEMPI
STOP
TEMPI
>
>
TEMPI RALL.
>
TEMPI
* When you press button TEMPI for the fi rst time you can use a START command from terminal no.16 or from a
remote control
IF YOU DON’T USE AN ENCODER:
SET UP THE SPEED WITH TRIMMERS
!

-17-
KEQS08 Technical Manual
The gate is in closed position
set the control board in Semiautomatic mode
(DIP 1A OFF - DIP 2A ON - DIP 7B OFF)
1Put in ON the DIP 10A Gate is closed
2 * Push the button TEMPI The motor OPENS
3
Push the button TEMPI (or START)
... If the slowing down is activated...
trimmer V RALL
The motor opens slowly
4
Push the TEMPI button (or START)
(if the opening limit switches is not
available).
Motor stops, starts the pause time
5... If the limit switch is available
wait until the motor stops
motor stops, the counting
of the pause time starts
Let the pause time run…
7Push the TEMPI button (or START) The motor CLOSES
8
Push the TEMPI button (or START)
if the slowing down is activated
(trimmer see V.RALL)
The motor closes slowly
9
Push the button TIMES (or START)
... if the closing limit switches no.1 is not
available...
Motor stops. Advanced learning
time completed
10 ... if the limit switches is available wait
motor stops
Motor stops. Advanced learning
time completed
The control unit detect the accessories under test and the opening manoeuvre can be delayed for a while
Connect the devices under Test according to the operating guide
1When the control is switched OFF, put in OFF dip 8 of DIP A
2Power the control unit and wait the LED is fl ashing
3Put in ON DIP 8 of DIP A
4Open the gate with a START command
or with the Working time learning see par. 6.1
The TEST function is compatible with slow response devices (for example TRANSCEIVER) so when those devices
are available the response time can be slower. You can test the devices in the STOP input.
Follow this procedure to know if some devices connected ot the inputs FOTO and STOP are under TEST.
ON
2
143 6 587 10 9
ON
2
143 6 587 10 9
LED
START
FORZA
20
40
60
80
100
Adjust of the force
of the motor from
20% up to 100%
V.RALL
MIN
2
4
6
8
10
OFF
Speed of slowing down (MINI-
MUM OFF) deactivation of the
slowing down. For the majority of
the motors the best value is from
MIN to 4. You need to adjust a
speed of 1/3 of the motor speed.
To deactivate the slowing down, turn the trimmer
in OFF
MIN
2
4
6
8
10
OFF
OBSTACLE DETECTION: If you
turn to MIN it needs only a lit-
tle bit of force to stop the motor,
the more you turn the trimmer
the more you need force. If you
turn to OFF the function is deac-
tivated.
BLOCK
V.RALL
FORZA
7 OPERATING GUIDE FOR TEST
8 Adjustment of the Trimmers .................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................

-18-
KEQS08 Technical Manual
8 Declaration of CE conformity
2 february 2017
the Administrator
(according to EC Directive 2006/42, Attachment II, part 1, ses. A)
The undersigned,
Administrator
DECLARES THAT:
Product’s name: KEQS08
Single phase for 230 Vac 1 motors
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
.................................................
2002/95/EC
THE PRODUCT COMPLIES
with what is outlined in the European Community directive:
2006/42/CE
EC DIRECTIVE 2006/42 ISSUED BY THE EUROPEAN PARLIAMENT
AND COUNCIL on may 17, 2006 harmonizing the legislation of the member
countries regarding machinery.
Reference: Attachment II, part 1, ses. A
(EC Declaration of Conformity issued by the manufacturer).
THE PRODUCT COMPLIES
with what is outlined in the European Community directives:
2014/35/EU
DIRECTIVE 2014/35/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 26 February 2014 on the harmonisation of the laws of the Member
States relating to the making available on the market of electrical equipment
designed for use within certain voltage limits.
Reference to harmonized standards: EN 60335-1
2014/30/EU
DIRECTIVE 2014/30/EU OF THE EUROPEAN PARLIAMENT AND OF THE
COUNCIL of 26 February 2014 on the harmonisation of the laws of the Member
States relating to electromagnetic compatibility.
Reference to harmonized standards: EN 61000-6-2 EN 61000-6-3
The directive 2006/42/CE remind that it is not allowed the function of
the product until the machine, for which the product is included, is not
indentify and declared conformed to the 2006/42/CE directive.

CASIT s.a.s.
Stab.: Strada Pietra Alta 1 - 10040
CASELETTE (TO) Italy
Tel. [phone]
Fax [phone]
Partita IVA 0050659.001.7
Reg. Trib. Torino N.654/62
C.C.I.A.A. 333122 - M: T0024777
www.casit.it
[email protected]
[email protected]