Matatakitoyo Torque Tools WET-500N User manual

•Worldwide 2.4 GHz ISM Band
•Directions & Accuracy : C.W. ±1％ / C.C.W. ±1.5％
•Display : 5 Digits LCD
•Temp. Range-OPerating : -5℃~55℃
•Temp. Range-Storage : -20℃~70℃
•Humidity : 0~90％
•RS-232 Data out / Optional
•Unit Selection : kg-m, N-m, ft.lb, in.lb
• Operating Mode : Auto Reset & Track (See Page-3 Tolerance Setting)
•Memory : 20 Readings
• Battery (Receiver) : 1.5V UM-3 (AA)x3 (Do not use low-discharge battery)
• Battery (Transmitter) : 1.5V UM-4 (AAA)x3 (Do not use low-discharge battery)
•Distance : 20m
WET
1. Study this instruction before use.
2. Please wear gloves and goggles when working.
3. This tool away from water, always store in a dry place and safe environment.
4. Do not over torquing the fastener, or it will cause tool’s damage and serious injury.
5. Never use additional accessories with this tester that were not included and are not from this
manufacturer, doing so could result in damage to the tester.
6. Always operate tester in a clean and organized work place.
7. This tester should always be kept clean, dry, and free from oil and grease.
8. This tool should be recalibrated a period of 1 years, or 5,000 cycles, whichever occurs first.
To contact with local vendor, an authorized repair center for supporting.
Manual
WARNING
BEFORE STARTING
SPECIFICATIONS
1 Years
5,000 Times
TORQUE
3/4” 1”
Models covered
OPERATION MANUAL
Wireless Torque Adaptor

FUNCTION
CONTENTS
PANEL
1 Receiver Power switch / Backlight switch
2 Down / Decrease
3 Up / Increase
4 Set
5 Memo
6 Zero / Quit / Confirm
7 Buzzer
8
Data out / RS232 / Optional
9 LED indicator (Green)
LED indicator (Yellow)
LED indicator (Red)
LCD-Display
Aux. / Reserved
Receiver Battery Box / AA x 3
Stander
Transmitter Battery / AAA x 3
Transmitter Power switch
Status LED
13
14
15
16
17
18
Transducer
(Transmitter)
Monitor
(Receiver)
Manual Supplied in a plastic box.
10
11
12
1
789 1112
10
2
6
53
15 4 14 13
16 18 17
1 Battery
2 Communication
3 Directions
4 Unit
5 Memo
6 Setting
7 Tolerance
8 Level Bar
5678
Wireless range may vary due to environ-
mental and computing conditions.
1 2 34
Press the Button 1 Time
LCD Blinking
Work mode
Idle LED light
Backlight ON Backlight OFF
Beep Sound Power OFF
Press the Button 1 Sec.
STATUS ICON DESCRIPTION

HOW TO USE
Power
Pre-set
Memory block
RS-232 Connection
Zero
Backlight
RS-232 Port
Power ON
Power OFF
Idle
Power Status
Select
Tolerance
Unit
Values
Transmitter Transmitter
0%：Track mode
1%~9%：Auto Reset mode
FCC ID : 2AC96WET ; 2AC96WDP
This device complies with Part 15 of the FCC Rules. Operation is subject to following
two conditions : (1)This device may not cause harmful interface, and (2) thisdevice
must accept any interface received, including interference that may cause undesired
operation.

MAINTENCE AND STORAGE
AUTO RESET MODE
DIMENSIONS
E-mail:[email protected]om
www.matatakitoyo.com
Made in Taiwan
MATATAKITOYO TOOL CO., LTD.
No. 63, Ln. 493, Sec. 3, Zhongshan Rd., Tanzi Dist.,
Taichung City 42754, Taiwan
TEL : [phone]
Manufacturer Aug. 2020
03
Version
Unit : mm
Level Bar (5% per dot)
1. Clean this tool by wiping with a clean cloth after operation and storage in a dry environment.
2. Do not dip any type of liquid in this tool. This may damage the internal of this tool.
A1
H
W
L
L1
ØD
ØD1
A
1.79
1.98
2.01
2.17
WET-500N
WET-1000N
WET-1500N
WET-2000N
100.0
97.8
98.0
97.8
3/4”
3/4”
3/4”
1”
3/4”
3/4”
3/4”
1”
L1
167.3
172.0
167.2
170.9
L
55.5
55.5
55.5
55.5
ØD
77.5
77.5
77.5
77.5
H
92.5
92.5
92.5
92.5
W
47
47
47
47
ØD1
50-500 Nm
100-1000 Nm
150-1500 Nm
200-2000 Nm
KG
A A1
ITEM NO. Range
Beep Speed
Slow Rapid
Tolerance ％
Torsion
Red
Green
Yellow
Over the range
Within the range
Lower then the range
Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
IMPORTANTNOTE : To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device
is permitted. Any change to the antenna or the device could result in the device exceeding the RF exposure requirements
and vcid user’s authority to operate the device.
Tolerance：1%~9%
Ex. : 1000Nm±5％