Cater-Wash CK8514 User manual

Cater-Wash CK8514 Trouble Shoot
Fault Error Codes Action Still not fixed. Run
test
Washing machine
stuck on pause 22, 23
Filling problems. - Make sure the
customers water pressure is above
0.5 bar. Make sure there is no
obstructions inside inlet hose. Make
sure Solonoid is not leaking.
Replace solonoid.
T06,
T09
Washing machine
stuck on pause or not
spinning.
31
Draining problems. Make sure the
customers filter is empty. Unscrew
the filter on the bottom right of the
washing machine with a tray
underneath and check not clocked.
Check the drain hose is clear. Check
the electrical connections to the drain
pump. Replace drain pump
CKP0226
T05
Washing machine
stuck on pause.
Detergent not entering
washing machine.
38, 39
Dispenser problems. Check for
obstructions in the despenser. Check
electical connection of the water
valves.
Replace the dispenser
motor.
Please always maker sure you have removed the travel bolts.
To find error codes
1. Turn the washing machine on.
2. Press ‘temp’ then ‘ewash’ then ‘temp’ then ‘ewash’ - Door will lock
3. Wait 10 seconds
4. T01 will display on the screen
5. Turn dial to T02 and press start . Any error codes will show on the screen now.

Fault Error Codes Action Still not fixed. Run
test
Stuck on pause.
Won't go into cycle. 42, 45, 46, 47 , 48
Motor - Make sure all the
shipping bolts and casing has
been removed. Remove
anything that may be stuck
between the drum obstructing
the drum. Look for any seized
barings on the machine.
Replace these as necessary.
Ensure inner drum can rostate
freely.
These errors can show up
if the washing machine
motor Has a loose
connection to the PCB.
You can get to this my
lifting the washing machine
back and make sure all
wires are plugged into the
motor properly. If not
replace
the
motor.
T10,
T11
Stuck on pause.
Won't go into cycle.
4A, 4B, 4C, 50, 52,
54.
Measure AC outlet voltage,
ensure correct range (187-242
VAC) Check electrical
connections at the drum motor
underneath the washer. Check
connection between drum
motor and drive motor (belt)
Unplug the unit wait 30
seconds and restart the
washing machine.
If the fault re appears -
replace the motor drive.
T10,
T12
Stuck on pause.
Won't go into cycle. 56
Replace the main control. PCB
Replace the main control.
PCB
Stuck on pause.
Won't go into cycle. 5,758
Main control internal problems.
PCB. Unplug the unit, wait 30
seconds, re start the unit.
Replace the main control
board. PCB

Fault Error Codes Action Still not fixed. Run
test
Door won't unlock. 60, 61, 63, 64
Door lock assembly problems. Check
the integrity of the wiring connections
between main control and door loack
mechanism. Check the door loack
mechansism (microswitch operation).
Lock and unlock the solonoid
continuously, contact integrity.
Replace the door lock
mechanism. Could also
be the PCB not allowing
the
lock
to
open.
Stuck on pause, Door
wont ulock. Won't
drain.
66, 67, 82 Water temperature problems. Check
wiring. Check thrmister resistance.
Replace thermister
assembly. Descale the
washer. Replace the
heating element if
necessary.
T07
Won't start cycle.
Stuck on pause. 62
System contact failure. Check
integrity of the wiring and
connections. Look for unsulation
break down and short circuit
conditions.
Replace PCB
Tripping electric
Make sure the washing machine is
not plugged into an extention cable.
Get the customer to check electrics.
Make sure no water dripping onto
electrics.
Replace
machine

Fault Error Codes Action Still not fixed. Run
test
Washing machine
banging metal on
metal
Check the mobility of the drum.
Damage to the back panel of the
unit when moving the washing
machine. Make sure the suspension
spings inside the washing machine
are still hooked into position and
havent come loose.
Replace the back panel
Washing machine
moving around
Ensure travel bolts and sleeves
have been removed. Check the
suspension spring are in place.
Check mobility of drum. Make sure
the washing machine is on a level
ground.
Buttons get stuck in. Replace the buttons.
No Power to the
washing machine
Can't run self
diagnostic
because no
power.
Make sure the washing machine is
not plugged into an extentions.
Change the fuse. Still no power
change the buttons
Buttons arent working
Check they havent pressed the child
'lock' button and loacked the
controls.