CDA hn6110 Reference manual

Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY
T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu
hn6110 Induction Hob
Manual for Installation, Use and Maintenance

2
Important
The CDA Group Ltd cannot be held responsible for injuries or losses
caused by incorrect use or installation of this product. Please note
that CDA reserve the right to invalidate the guarantee supplied with
this product following incorrect installation or misuse of the appliance
or use in a commercial environment.
This appliance is not designed to be used by people (including
children) with reduced physical, sensorial or mental capacity, or
who lack experience or knowledge about it, unless they have had
supervision or instructions on how to use the appliance by someone
who is responsible for their safety.
Under no circumstances should any external covers be removed for
servicing or maintenance except by suitably qualified personnel.
Appliance information:
Please enter the details on the appliance rating plate below for
reference, to assist CDA Customer Care in the event of a fault with
your appliance and to register your appliance for guarantee purposes.
Appliance Model
Serial Number
CE Declarations of Conformity
This appliance has been manufactured to the strictest standards and
complies with all applicable legislation, including Electrical safety (LVD)
2006/95/EC and Electromagnetic interference compatibility (EMC)

3
2004/108/EC. Parts intended to come into contact with food conform
to 89/109/EC.
IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE
PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must be taken to a special
local authority waste collection centre or to a dealer providing
appliance recycling services.
Disposing of a household appliance separately avoids possible
negative consequences for the environment and health. It also
enables the constituent materials to be recovered, saving both energy
and resources. As a reminder of the need to dispose of household
appliances separately, the product is marked with a crossed-out
wheeled dustbin.
Precautions before use
• Unpack the hob and all associated components, taking care not to
lose or mishandle any parts.
• We recommend that the appliance is installed by a suitably qualied
professional and connected to the electricity supply by a qualified
electrician, who is a member of the N.I.C.E.I.C. and who will comply
with the I.E.T. and local regulations.
• The appliance must be installed in a purpose-designed kitchen unit
and worktop cut out as specified below.
• This hob (Class 3) has been designed for use only as a domestic
cooking appliance. Any other use should be considered incorrect
and therefore dangerous.
• Remove all labels and other packaging materials from the ceramic

4
surface prior to use.
• Do not modify the appliance in any way as this will invalidate the
guarantee and is potentially dangerous.
• The hob top is not designed for any use other than cooking: any
other use (e.g. as a worktop) is potentially dangerous and will
invalidate the guarantee.
• This appliance must be connected to xed wiring and suitably
earthed according to local regulations. Alternative connection,
through a 13A plug or through an extension lead must not be used.
• This appliance must not be installed above a dishwasher, washing
machine or tumble dryer as steam may damage the electronic
components.
Using the Appliance
• Always switch cooking zones o after use.
• Take particular care when cooking with oils or fats that may ignite.
• Cooking pans and utensils and the hob itself become hot during
use. Caution, risk of injury to people and pets both during and after
use.
• Ensure no cable from any other appliance can come into contact
with the hob top or pans during use.
• Magnetic objects (such as credit cards or portable electronic
devices) must not be placed near the hob during use.
• Do not place any metal object (other than suitable pans) on the hob.
• Never cover the hob with any cloth or other cover. This may
become hot and create a re hazard.
• This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental

5
capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
• Children shall not play with the appliance.
• Cleaning and user maintenance shall not be made by children
without supervision.
• Metal objects such as knives, forks, lids etc. should not be placed
on the hob as they may become hot.
Precautions to protect the hob
• Use of damaged pans or those with raw cast iron bottoms may
damage the hob ceramic glass.
• Abrasive materials such as scouring cleaners and grits may damage
the ceramic glass.
• Avoid dropping objects onto the ceramic glass.
• Take care not to strike the edges of the hob with saucepans.
• Ensure that ventilation (as specied under installation instructions)
remains free from obstructions.
• Do not place empty saucepans on the hob.
• Sugar, synthetic plastics or aluminium foil must not be allowed
to come into contact with the heating zones; these may cause
permanent damage to the ceramic glass. If these should
accidentally fall onto the hob, turn it o immediately and carefully
remove them. Take care not to burn yourself.
• Never place any hot items on the control panel.
• If a drawer is located below the hob, ensure a horizontal divider is
installed leaving a minimum gap of 2cm above it for hob ventilation,
and protecting the drawer contents from striking the hob. The

6
divider must be made of material capable of withstanding 65°C
above ambient temperature.
• Never place inammable items or materials in a drawer or cupboard
below the hob.
Precautions in the event of an appliance fault
• If a fault is noticed, switch o the appliance and turn o the
electricity supply.
• Warning: If the ceramic glass is broken or cracked do not use the
appliance, turn o the electricity supply to avoid the possibility of
electric shock. Contact CDA Customer Support.
• There are no user-serviceable parts inside the appliance; all repairs
must be performed by a suitably qualified service engineer or
similar.
• See the “Troubleshooting” section in this manual, from page 17.
Other precautions
• Ensure that each pan is centred on its cooking zone; The pan base
must cover as much of the cooking zone as possible.
• Do not use aluminium or plastic containers: they could melt onto hot
cooking zones.
• The use of incorrect cookware or any induction adaptor plate
designed for non-magnetic cookware is outside the manufacturer’s
specifications so will invalidate the guarantee. The manufacturer
cannot be held responsible for any damage to the hob or
consequential damages as a result of such use.

7
FOR THOSE WITH HEART PACEMAKERS OR ACTIVE IMPLANTS:
The function of this hob conforms to current electromagnetic
interference standards and thus is in total compliance with legal
requirements (2004/108/CE directives).
To avoid interference between your hob and a pacemaker, your
pacemaker must be designed and programmed in compliance with
the regulations that apply to it. As such, CDA guarantee only that our
product is compliant.
With regard to the compliance of the pacemaker or any potential
incompatibility, you should obtain information from the manufacturer or
your attending physician.

8
Cooking On Induction
The principle of induction cooking is based on magnetic eect.
When you put your cookware on an induction zone and switch it on,
the electronic boards in the hob produce induced currents in the base
of the cookware and instantly raise its temperature. This heat is then
transferred to the food inside the cookware.
The best cookware to use with induction cooking has thick at bases,
as the heat will be better distributed so cooking more evenly.
Most cookware is compatible with induction cooking. There are three
ways to check the suitability of your cookware:
1. Use a magnet to see if the base of the pan is magnetic: if the
magnet sticks, then the cookware is compatible.
2. Place the pan on one of the cooking zones switched on to power
level 4: If the display remains on, then the cookware is
compatible. If the display ashes, the cookware cannot be used on
an induction hob.
3.Check the instructions or packaging of the pans for the symbols
indicating suitability for use with induction.

9
Using Your Hob
Fig.1
Control panel:
3. Power key
4. Timer display
5. Zone selection keys
6. Zone displays
7. - key
8. + key
9. Timer control light
Zones:
1. Front Left 1.85 kW 175 mm
2. Rear Left 1.4 kW 175 mm
3. Rear Right 1.85 kW 175 mm
4. Front Right 1.4 kW 175 mm
4
7
5
3 6
8
9
2
1
3
4

10
Using Your Hob
The table below oers guidance as to what each power level is for.
To switch the hob on
To switch the power on, touch and hold the key for approximately
two seconds. The hob will beep and all zone displays will show zero.
Please note: If a power level is not set within ten seconds, the hob
will switch o automatically.
To set the power level
Touch the “Zone selection” key for the zone required, then set the
power level by touching the “+” or “-” keys within ve seconds.
To increase the power level from 1 (minimum) toward 9 (maximum),
touch the “+” key.
To go straight to power level 9, touch the “-” key when the zone
display shows “0”.
Power level Type of cooking
0Switched o
1/2 Melting (butter/chocolate) or keeping food warm
2/3 Keeping food hot or to heat small quantities of liquid
3/4 Heat larger quantities of liquid (sauces etc.)
4/5 Slow boiling, e.g spaghetti, soups, stews, potatoes
6/7 Gentle frying
7/8 Browning meats, frying fish, omelettes
9 Fast frying steaks

11
To turn the power o
To switch o a single zone, touch the “Selection” key for the zone no
longer required. Touch the “-” key until the zone display shows zero.
When all zones are at zero, the hob will switch o automatically after
approximately ten seconds.
Alternatively, to switch o the hob immediately, touch and hold the
key for approximately two seconds.
Booster (front left and rear right zones only)
The hob is equipped with a booster function, allowing a higher
power level than the maximum on these zones for approximately ten
minutes. To turn on the booster function, touch the “+” key when the
power level is already set at 9. “P” will show in the display. To cancel
the booster at any time, touch the “-” key to return to power level 9.
Timer
The hob is equipped with a timer that allows a finish time to be set for
the end of cooking on one or more zones, between a minimum of
one minute and a maximum of 99 minutes. This timer can be used
independently for dierent times on each zone.
To set the timer
•Switch on the power.
• Touch the “Zone selection” key for the zone required, then set the
power level by touching the “+” or “-” keys within ve seconds, as
above.

12
• Touch both the “+” and “-” keys at the same time to select the timer.
The timer display will show “00”.
• Set the required duration using the “+” or “-” keys within ve
seconds. Touching the “-” key will go straight to 30 minutes. Touch
and hold the timer “+” or “-” keys to scroll through the duration
quickly.
• After approximately ve seconds, the control LED stops ashing
and the countdown will start.
• At the end of the set time, the selected zone will switch o and the
timer display will ash “00”. The hob will beep for approximately
one minute.
• To switch o the beep and the ashing displays, touch any key.
To cancel the timer
• Touch the “Zone selection” key for the zone you wish to cancel the
timer from.
• Touch both the “+” and “-” keys at the same time to select the timer.
The timer display will show the time remaining.
• Touch “-” key to stop the timer.
Please note: Cancelling the timer will not switch o the zone. You
should switch the zone o manually if required.
Please note: the power level can be adjusted during the
countdown using the “+” or “-” keys.

13
Minute minder
When no cooking zones are being used, the timer can be used as a
minute minder.
To Set the Minute Minder
• Touch both the “+” and “-” keys at the same time to select the timer.
The timer display will show “00”.
• Set the required duration using the “+” or “-” keys within ve
seconds. Touching the “-” key will go straight to 30 minutes. Touch
and hold the timer “+” or “-” keys to scroll through the duration
quickly.
• After approximately ve seconds, the control LED stops ashing
and the countdown will start.
• At the end of the set time, the the timer display will ash “00” and
the hob will beep for approximately one minute.
• To switch o the beep and the ashing displays, touch any key.
Key Lock
The hob is equipped with a key lock to lock the controls. This can be
used when the hob is o.
To turn on the key lock
If the hob is not already turned on, turn it on by touching the key.
Touch the “-” key and the “Zone selection” key for the front right zone
at the same time, then touch just the front right zone “Zone selection”
key. The hob beeps and all the zone displays show “L” to conrm the
key lock is switched on.

14
To turn o the key lock
If the hob is not already turned on, turn it on by touching the key.
Touch the “-” key and the “Zone selection” key for the front right zone
at the same time, then touch just the “-” key.
The hob beeps to conrm the key lock is switched o, then the hob
switches o. When turning the hob back on the key lock is turned o.
Residual heat indicators
The hob is equipped with residual heat indicators to warn when any
of the zones are still hot to the touch after cooking. An “H” will show
in the relevant zone display after cooking until the zone is at a safe
temperature to touch.
In the event of a power cut, the residual heat indictors will illuminate
after the power supply is restored. However, when there is no power
supply to the hob the residual heat indicators will not work, so extra
care must be taken.
Please note:
You should avoid touching the zones when the hob is in use, or when
an “H” is showing on the zone display.
Pan detection
The hob is equipped with a sensor that will advise when the pan is
removed from the zone, or is unsuitable for use on induction hobs.
The zone display will show “U” until a suitable pan is placed on the

15
zone. The zone will switch o after approximately one minute if no
suitable pan is placed on the zone.
Ecient Use of Your Hob
The hob is equipped with zones of dierent sizes, designed to
accommodate most shapes and sizes of pan. For best results,
only use pans with at bottoms and choose an appropriate zone
depending on the size of the pan. The most ecient use of the hob is
shown below, where the pan and zone are correctly chosen.
Use pan lids where possible to minimize the energy usage of your
appliance.
Zone Size Minimum Pan Size (cm) Maximum Pan Size (cm)
175mm 10 20
It is very important that the pans used on the hob are made of a
suitable material and have the correct type of base. The base of the
pan must be clean before use to prevent any scratches on the hob
top.
Fig.2

16
Care and Maintenance
Always disconnect the appliance from the power supply before
undertaking any cleaning or maintenance.
Important:
•Steam cleaners must not be used when cleaning this appliance. •
You should use a non-abrasive cleaner to clean the hob top. Any
abrasive cleaner (including Cif) will scratch the surface and
could erase the control panel markings.
•Sugar and starch can cause permanent damage to the surface of the
hob. Wipe away any spillages immediatly.
If your hob is not working:
1. Check that the zone is switched on.
2. Check that the mains supply has not been switched o.
3. Check that the fuse in the spur has not blown.
Types of residues Clean with Cleaning advice
Light Cleaning sponge and soft
cloth
Wipe over the zone to be cleaned with a
sponge and hot water, and then wipe o with a
soft dry cloth.
Accumulated baked-on
stains/dirt, sugar spills or
melted plastics
Cleaning sponge or glass
scraper and soft cloth
Wipe over the zone to be cleaned with a
sponge and hot water, using a ceramic scraper
to remove any large marks or stains and then
wipe o with a soft dry cloth.
Rings and hard water
residues
White vinegar and soft
cloth
Pour a small amount of warm white vinegar
onto the stain, leave it to stand, and then wipe
o with a soft dry cloth.
Shiny metallic streaks Cleaning agent for
vitroceramic glass etc.
Use specialist vitroceramic glass cleaner
(preferably one with silicone for its protective
properties)

17
In the event of a fault with the hob, please advise CDA Customer Care
of any fault code shown on the display
Contact CDA Customer Care
A: Customer Care Department, The CDA Group Ltd, Harby Road,
Langar, Nottinghamshire, NG13 9HY
T: 01949 862 012 F: 01949 862 003
E: [email protected] W: www.cda.eu
Troubleshooting
On rst use
You observe that Possible Causes What should you do?
The display shows a series
of digits and symbols on first
connection
Working normally
Nothing, the hob will be ready
to use within approximately 10
seconds
Installation blows a fuse or
only one side of the hob works
The electrical connection of the
hob is incorrect
Check that it is set up properly
(see the Electrical Connection
section)
The hob produces an odour
during the first cooking sessions New appliance
Heat a saucepan full of water
on each cooking zone for 30
minutes
You observe that Possible Causes What should you do?
The hob does not work and the
lights on the control panel do not
switch on.
The hob is not connected to
the power supply or the power
supply is faulty.
Check the electrical circuit
breaker and fuses.
The hob is not working and the
display shows a non-standard
graphic.
The electronics are not
functioning correctly. Call CDA Customer Care.
The hob is not working and all
the zone displays show “L”. The key lock is on. Switch o the key lock before trying to use the hob.
9 fast frying steaks
On switching on

18
In use
You observe that Possible Causes What should you do?
One or all of the zones cuts out.
The safety system has cut out. Leave hob to cool then try it
again
A cooking zone has been
running for a very long time Switch it on again (if required).
One or more control keys are
covered.
Clear any objects and clean
liquid from the control area.
A pan has boiled dry and is
overheating. Remove the pan in question.
The fan continues to run after the
hob is switched o.
This is not a fault, the cooling
system is working correctly. Nothing.
“U” ashes on the zone display.
The cookware used is not
suitable for induction.
See page 8 for information on
cooking on induction
There is no pan on the cooking
zone.
Place a suitable pan on the
cooking zone.
The base diameter of the pan is
too small.
Place a larger pan on the
cooking zone.
“L” shows on the zone display. The key lock is on. Switch o the key lock before
trying to use the hob.
“Er03” shows on the zone
display.
One or more control keys are
covered.
Clear any objects and clean
liquid from the control area.
“E2” shows on the zone display. The hob is overheated. Let it cool down, then try it again.
“E3” shows on the zone display. The cookware used is not
suitable for induction.
See page 8 for information on
cooking on induction
“E4” or “E C” shows on the zone
display. Hob configuration error. Contact CDA Customer Care for advice.
“E5” shows on the zone display. Network voltage supply fault. Check the connection and
reconnect the hob.
“E6” shows on the zone display. Network frequency supply fault. Check the connection and
reconnect the hob.
“E8” shows on the zone display. The ventilation air inlet is
blocked. Clear the ventilation air inlet.
“U400” shows on the zone
display. The hob is not connected to the
power supply
Check the connection and
reconnect the hob.

19
IMPORTANT - PLEASE NOTE: In the event of any breakage, crack
or cracking – even minimal – of the vitroceramic glass, immediately
disconnect your appliance to prevent a risk of electric shock and
contact CDA Customer Care.
IMPORTANT:
When correctly installed, your product meets all safety
requirements laid down for this type of product. However, special
care should be taken around the rear or the underneath of the
appliance as these areas are not designed or intended to be
touched and may contain sharp or rough edges that could cause
injury.
Fitting the Hob
Unpacking the hob:
Take care not to lose or mishandle any parts.
Fitting position of the hob:
This appliance must be installed a minimum of 50mm from any
back wall and a minimum of 180mm away from any adjacent vertical
surfaces, e.g. a tall cupboard end panel. This may be reduced to
100mm if the adjacent surface is resistant to fire (tiles or steel, for
example). These dimensions are shown in Fig. 5.
Ventilation requirements:
This appliance must be installed to allow air to ow freely to the air
intake, from the air outlet and in the base and run of units into which
it is installed (Fig 3). Failure to allow sucient ventilation could cause

20
damage to the hob and constitutes incorrect installation, which is not
covered by the warranty.
Notes:
•This could be a simple slot cut out of the plinth, or a dedicated
ventilation grille.
•The furniture top rail should not be fitted to the unit. This allows the
induction hob to exhaust air into the kitchen space.
• The recommended ventilation sizes are for guidance only.
If tting a cooker hood above the hob:
If a cooker hood is to be installed above the hob, the height of
the hood above the hob must be at least 600mm (650mm is
recommended) (Fig. 4). If the instructions supplied with the hood
dictate that the hood must be installed at a height greater than
600mm, then that height is the minimum required.
Wall furniture requirements:
The minimum height of any cabinet immediately above the hob is
900mm. The minimum height of any adjacent units (including light
pelmets) is 400mm, unless they are manufactured from a material
resistant to fire (steel, for example).
Notes:
•Do not position this appliance above a refrigeration unit. The heat
generated may cause the refrigeration unit to fail.
•This appliance is designed to be installed into cabinet units capable
of withstanding temperatures of 65°C or greater above ambient