CEA LFP-EA-SY1-1280 User manual

CEA Portable Power Station
LFP-EA-SY1-1280
User Manual
CEA electric co.,ltd
Read through the user manual before use.

General Specification:
Principle : Portable power station is a big size battery, it works by output DC voltage or AC voltage
through inverter, when the battery runs out ,it could be recharged via wall socket, solar board,
cigarette charger.
Devices : Mini refrigerator, printer, computer, laptop, POS, drone, smart phones, lamps and devices
rated power no more than 1000W. The portable power station support pass-through charging.
British socket
Option
AC Output
Euope Socket
Application
Description
1.Main part : Housing, LiFePO4 battery, Inverter, LCD display, Function board.
2. Function board introduction:
Cigarete lighter port X1
USB output X2
AC socket X2
Anderson port
AC output ON/OFF button
USB output ON/OFF button
LCD Display
DC output ON/OFF button
Power ON/OFF button
DC5521 Port X2
type-C port output X2

LCD Display Introduction
Power Status Error Indicator
Error Indicator
Recharging Power Status
Discharge Power Status
AC Output Frequency
Output DC12V Discharging
Output AC DischargingOutput USB
Type-C Discharging
Output USB
Discharging
Overheat Indicator
Fuse
Input : AC Port

Parameter
How to use
1 Recharging.
1.1 Wall charger. CEA power station is designed with built-in adapter to charge from wall socket. Connect power cord
attached from one side to power station input port, the other side connect to AC wall socket. Input voltage 100-240V,
50/60Hz.
1.2 Solar board. Connect the wire from solar board to Anderson port on power station, be care to connect positive and
negative correctly. It support max input 400W (11-60V 10A)with MPPT.
1.3 Car port charging . Connect cigarette lighter on the vehicle port, the other side connect to Anderson port on power
station, be care to connect positive and negative correctly. It support max 120W(12V 10A) input.
2 Discharging.
2.1 AC socket .Make sure the device you want to use is performing properly, the device rated power should not over 1000W.
Insert the plug from device to the AC socket on power station, first press power button on , second press AC ON/OFF
button on, AC symbol on LCD display will turn green, then you may switch on the device connected. Shut off operation
is the reverse of discharging operation. Attention! The device power connected in total should not over 1000W, otherwise
power station will shut off automatically.
2.2 USB port. Connect devices to USB port properly, first press power button on, second press USB ON/OFF button on, USB
or Type C symbol on LCD display will turn green, then the devices will be recharged. Shut off operation is the reverse
of discharging operation.
Project Description
Battery 1280WH LiFePO4
Dimension(LxWxH) 378x265x239mm
N.W. 13kg(28.6 lb)
Ambient Temperature -10~40°C(14° to 104°F)
Storage Temperature -10~40°C(14° to 104°F)
Input
wall socket 1100W(110V 10A,60Hz, built-in adapter)
solar board Max 400W(11-60V 10A)
cigaretter lighter Max 120W(12V 10A)
Recharging time
wall socket about 1.2 hours
solar board about 3.2 hours
cigaretter lighter about 11 hours
Output
AC Socket 2x America Socket, 110V,60Hz,max 1000W
USB A1/A2 max18w(5V 3A,9V 2A,12V 1.5A)
support quick charging(QC3.0/QC2.0/AFC/FCP/SCP/BC1.2/Apple)
USB C1/C2(type C) max100w(5V 3A,9V 3A,12V 3A,15V 3A,20V 5A
support quick charging(PPS/PD/QC3.0/QC2.0/AFC/FCP/SCP/BC1.2/Apple)
DC port 5521x2,cigaretter lighter 12V 10A
wireless charger 10W
Lighting LED work light 2W
LED flash light 2W with SOS flash
(400W board with MPPT)

2.3 DC port. Connect devices to 5521 port or cigarette lighter, first press power button on, second press DC ON/OFF
button on, DC symbol on LCD display will turn green, then you may switch on the devices connected. Shut off
operation is the reverse of discharging operation.
3 Wireless charger
First press power button on, second press USB ON/OFF button on, USB or Type C symbol on LCD display will turn
green, then put the device on wireless charger area. Shut off operation is the reverse of discharging operation.
4 Lighting.
4.1 LED work light. It is on side of the carrier, first press power button on, then press the light button on.
Troubleshooting
Symptom Solution
The product fails to start.
The DC, USB,and AC ports
have no output.
1. Remove all electrical equipment, charge the product for 10 minutes, then start it again.
2. Ensure the product is used in normal temperature range.
The product can be
started,but corresponding
output ports(DC,USB,AC)
have no output.
1. Check whether the status of charge of the product is too low. If so,charge it in time.
2. Check whether the power of the electrical equipment is over power station rated power. If
so,remove the equipment and start the product again.
3. Check whether there is a short circuit between output port and electric equipment. Remove
the equipment and restart the product.
4. Connect the equipment to another power supply and check whether it works properly. The
product may not be compatible with certain euqipment.
The product is shut down
accidentally during use.
The product is shut down because the internal protection system starts due to events such as
overcharge, overdischarge, high temperature, low temperature,overcurrent, and short circuit.
Remove all the electrical equipment , keep the product in normal temperature range, charge it
for 10 minutes, start the product again.
Fails to charge.
Check whether the charging electrical parameters are within the charging range of the
product.

Maintenance
Cleaning
Storage
Disposal/Recycle
WARNINGS
Be sure power station is disconnected from all input power sources and output devices. Use a dry clean cloth to wipe
the case, remove any debris, dirt or other blockages .
If storage for more than 1 month, charge fully before storage and recharge approximately every 3 months to avoid full
discharge and possible damage. Storing indoor, temperature -10~65°C(14° to 149°F),keep away from direct sunshine.
Leaving in a vehicle or other confined spaces in extremely hot temperature can lead to decreased service life,
overheating, and fire. Extreme cold temperature below specific storage range can also do harm to performance and
service life. Keep away from corrosion chemicals and gases.
It is recommended to get portable power station fully recharged before using for the first time.
In the case of long-term storage ( more than 3 months), ensure status of charge is 50% or higher.
Use the product in temperature range of -10~65°C(14° to 149°F) ,beyond this range will shorten its service life.
Do not place equipment and its accessories in the trash. Items must be appropriately disposed in according with local
regulations.
To ensure safe operation and service of the power station, follow these instructions. Failure to observe these warnings
can result in severe injury or fire. The AC output of the product is 110V. Do not insert your hand or metal conductors into
the AC sockets.
To avoid unknown hazards, do not open the product without permission.
Charge with original accessory to avoid fire, explosion or other hazards.
Select a solar panel based on the electrical parameters specified by the manufacturer. Voltages above the specified
range may damage the product.
If the product smells abnormally or heats up during charging or storage, stop charging immediately and place it in an
open place for remote observation. After confirming that it is safe, contact the manufacturer or dealer.

Packing list
CEA ELECTRIC CO.,LTD
Address : 55th Dingda Road, Fuyang Industrial Zone,
Yingquan District, Fuyang,Anhui,China. 236000
Tel : [phone] Fax : [phone]
Email : [email protected]
Website : www.cealite.com
1 Portable power station x1 set;
2 AC recharging Power cord x1 piece;
3 Cigarette charger wire x1 piece;
4 User manual x1 piece.
This product and its accessories may contain small parts. Keep the product and its accessories out of reach of children.
Children may inadvertently damage this product and its accessories, or swallow small parts, causing suffocation or
other hazards. Children or persons with intellectual disability should be accompanied by a guardian to use this product.
Do Not disassemble or modify the product, insert foreign object into the product, or immerse it in water or other liquids
to avoid leakage, overheating, fire, or explosion.
Do Not short-circuit the positive and negative terminals of each output port.
Do Not use a product with obvious damage. Do not use damaged wires or plugs to connect to the product which may
cause electric shock.
Do Not use the portable power station over its output rating. Overload outputs may result in a risk of fire or injury to
persons, even though we have built-in overload protection.
Do Not use the portable power station or AC wall charger, if it is damaged or has been modified. Damaged or modified
batteries may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury.
Do Not subject to vibration , impacts, or drops. Secure the the portable power station during transport.
Do Not place the unit on its side or upside down while in use or in storage.
Do Not use the product at an attitude of more than 2000m.
Do Not use this product during thunderstorms. Thunderstorms may cause product failure or electric shock hazard.
Do Not drop, squeeze, or puncture the product. Avoid exposing the product to excessive external pressure, which can
cause internal short circuit and overheating.
It is prohibited to store or transport the product with keys, metal ornaments, or other metal objects.
Do Not throw the product into the fire. Otherwise , product may catch fire and explode.