GENERAL DESCRIPTION
This device is a conventional beacon that mounts on the low profile base.
This beacon is designed to flash every 2 seconds (0.5 Hz).
IMPORTANT GUIDELINES
Apply the guidelines below:
-be sure to install the beacon according to local standards and regulations;
-this product is designed for indoor use only;
-beacon should only be installed in environments where ambient temperature and humidity fall into the ranges specified in the
TECHNICAL SPECIFICATIONS table;
-only install in suitable environments, avoiding:
situations in which condensation exists;
situations in which corrosive gases exist;
situations in which obstacles exist, which could impede visual indication of the beacon;
hazardous areas;
-connect the adaptor base according to the scheme provided by this manual;
-constructor recommends that the minimum period of maintenance should be 1 year and that the following should be taken into
account:
a regular operation test should be performed;
a visual check for contamination and mechanical damage should be made.
TECHNICAL SPECIFICATIONS
L20-CBE1002-7200 (vA.1)
ADAPTOR BASE INSTALLATION
1) Select the position on the ceiling where you want to install the beacon.
2) Install the adaptor base in the selected ceiling position by inserting the screws in the
circles indicated in figure 1.
WIRING
The adaptor base has to be connected to a sounder / powered circuit and NOT to a zone.
BEACON PLACEMENT
1) Position the beacon centrally on its adaptor base ensuring it is level.
2) Rotate clockwise applying gentle pressure. The beacon will drop into its keyed location.
3) Continue to rotate clockwise a few degrees until the beacon has fully engaged in the adaptor base.
4) When the beacon is firmly engaged, check the alignment of the raised reference mark on the beacon and on the base (figure 4).
CEASEFIRE INDUSTRIES PRIVATE LTD., E6, UPSIDC Industrial area, Selaqui, Dehradun, Pin Code - 248001, Uttarakhand, India
12
Figure 1
Power supply range from 15 V to 40 V
Current draw in activated state 10 mA at 24 V
Power consumption in activated state 240 mW at 24 V
Installation location Ceiling
Maximum allowed height from ground 3 m as certified per EN 54-23
Horizontal coverage diameter 7.5 m at 3 m from the ground
as certified per EN 54-23
Coverage volume 132 m3at 3 m from the ground
as certified per EN 54-23
Category rating C-3-7.5 as certified per EN 54-23
Flash rate 0.5Hz 1 flash every 2 seconds
Flash color White
Temperature range -30 °C to +70 °C
Max humidity 85% RH no condensation
IP 21C
POWER (+)
POWER (-)
SHIELD SHIELD
Figure 2
Figure 3
Figure 4
WARNINGS AND LIMITATIONS
Our devices use high quality electronic components and plastic materials that are highly resistant to environmental deterioration.
However, after 10 years of continuous operation, it is advisable to replace the devices in order to minimize the risk of reduced
performance caused by external factors. Ensure that this device is only used with compatible control panels. Detection systems
must be checked, serviced and maintained on a regular basis to confirm correct operation.
Smoke detectors may respond differently to various kinds of smoke particles, thus application advice should be sought for spe cial
risks. Detectors cannot respond correctly if barriers exist between them and the fire location and may be affected by special envi-
ronmental conditions.
Refer to and follow national codes of practice and other internationally recognized fire engineering standards.
Appropriate risk assessment should be carried out initially to determine correct design criteria and updated periodically.
WARRANTY
All devices are supplied with the benefit of a limited 3 years warranty relating to faulty materials or manufacturing defects, effective
from the production date indicated on each product.
This warranty is invalidated by mechanical or electrical damage caused in the field by incorrect handling or usage.
Product must be returned via your authorized supplier for repair or replacement together with full information on any problem identi-
fied.
Full details on our warranty and product’s returns policy can be obtained upon request.
TI-002271
CONVENTIONAL BEACON FLASH RATE 2HZ 928x/02
