CEL-MAR ADA-7200 User manual

User manual
ADA-7200
Multidrop Fiber Optic Repeater
1
io_ada-7200_v3.17_en
ADA-7200
Copyright © 2001-2020 CEL-MAR sp.j.

Contents
1. ENERAL INFORMATION...................................................................................................................................................................... 3
1.1. WARRANTED INFORMATION....................................................................................................................................................... 3
1.2. ENERAL CONDITIONS FOR SAFE USE.................................................................................................................................... 3
1.3. CE LABEL....................................................................................................................................................................................... 3
1.4. ENVIRONMENTAL PRESERVATION............................................................................................................................................ 3
1.5. SERVICE AND MAINTENANCE..................................................................................................................................................... 3
1.6. PACK CONTENTS.......................................................................................................................................................................... 3
2. PRODUCT INFORMATION..................................................................................................................................................................... 3
2.1. PROPERTIES................................................................................................................................................................................. 3
2.2. DESCRIPTION................................................................................................................................................................................ 4
2.3. ISOLATION..................................................................................................................................................................................... 4
3. INSTALLATION....................................................................................................................................................................................... 5
3.1. CONNECTION FIBRE-OPTIC BUS................................................................................................................................................ 5
3.2. WIRIN TOPOLO Y FIBER OPTIC BUS...................................................................................................................................... 5
3.3. EXAMPLES OF CONNECTION THE CONVERTER TO FIBER OPTIC BUS................................................................................6
3.4. POWER SUPPLY CONNECTION.................................................................................................................................................. 7
4. ACTIVATION........................................................................................................................................................................................... 7
4.1. DESCRIPTION OF SI NALLIN LEDS.........................................................................................................................................7
5. VERSIONS.............................................................................................................................................................................................. 7
6. SPECIFICATION..................................................................................................................................................................................... 7
2
ADA-7200

1. G N RAL INFORMATION
Thank you for your purchase of C L-MAR Company product. This product has been completely tested and is covered by a two year
warranty on parts and operation from date of sale.
If any questions or problems arise during installation or use of this product, please do not hesitate to contact Technical Support at +48
41 362-12-46 or e-mail [e-mail].
1.1. WARRANT D INFORMATION
ADA-7200 repeater is covered by a two year warranty from date of sale. In case of being damaged it will be repair or the damaged
component will be replace. The warranty does not cover damage caused from improper use, materials consumption or any
unauthorized changes. If the product does not function (is damaged), or not operate in accordance with the instructions, will be
repaired or replaced.
All warranty and no warranty repairs must be returned with paid transport and insuring to the C L-MAR Company.
C L-MAR Company under no circumstances won't be responsible for ensuing damage from improper using the product or as a result
of random causes: the lightning discharge, the flood, the fire and the like.
C L-MAR Company is not be held responsible for damages and loss including: loss of profits, loss of data, pecuniary losses ensuing
from using or the impossibility of using this product.
In specific cases C L-MAR Company discontinue all warranties and in particular do not follow the user manual and do not accept
terms of warranty by the user.
1.2. G N RAL CONDITIONS FOR SAF US
The device should be installed in a safe and stable places (eg, electroinstallation cabinet), the powering cable should be arranged so
as not to be exposed to trampling, attaching, or pulling out of the circuit.
Do not put device on the wet surface.
Do not connect devices for nondescript powering sources,
Do not damage or crush powering wires.
Do not make connection with wet hands.
Do not adapt, open or make holes in casings of the device!
Do not immerse device in water or no other liquid.
Do not put the fire opened on device sources: candles, an oil lamps and the like.
Complete disable from the supply network is only after disconnecting the power supply circuit voltage.
Do not carry out the assembly or dis-assembly of the device if it is enabled. This may result to short circuit and damage the device.
The device can not be used for applications that determine human life and health (eg. Medical).
ATT NTION!!!
The device is equipped in the laser transmitter.
The radiation emitted by the laser transmitter is harmful to the eyes!
Under no circumstances should never look to at the uncovered slot, to which it is not connected the fiber optic
connector.
The manufacturer is not responsible for used not in accordance with the instruction manual.
The user manual is an integral part of the device and with it is delivered to users.
1.3. C LAB L
The CE symbol on the device CEL-MAR means compatibility with electromagnetic compatibility Electromagnetic
Compatibility Directive MC 2014/30/W .
Declaration of Conformity is delivered with purchased device.
1.4. NVIRONM NTAL PR S RVATION
This sign on the device inform about putting expended device with other waste materials. Device should send to the
recycling. (In accordance with the act about the Electronic Appliance Expended from day 29 of July 2005)
1.5. S RVIC AND MAINT NANC
ADA-7200 repeater does not require the servicing and maintenance.
Technical support is available at number [phone] in 8.00-16.00, from Monday to Friday or e-mail [e-mail].
1.6. PACK CONT NTS
ADA-7200 repeater; user manual; CE declaration.
2. PRODUCT INFORMATION
2.1. PROP RTI S
●Regeneration of Fiber Optic signal – Fiber Optic repeater,
●Fibre-Optic connection via fore fibre connectors type: ST® * or SC – transmitter and receiver for an optical wavelength from 792nm
to 865 nm or SMA – transmitter and receiver for an optical wavelength from 640nm to 675nm.
●Fibre Optic line: 2 mutimode optical fibres eg. type 50/125 mm, 62,5/125 mm, 100/140 mm, 200 mm HCS, 1mm POF,
●Baud rate up to 5Mbps,
●Transparent for all protocols: MODBUS, DNP, PROFIBUS and other,
●External power supply 10 - 30 VDC stable min. 3W,
●1kV= or 3kV= galvanic isolation between FO interface and power supply,
●Connection power supply via screw terminal block,
3
ADA-7200

●Connection Fiber Optic network via fibres optic connectors type: ST® *(850nm), SC(850nm), SMA(650nm),
●Protection against power supply reverse connection,
●DIN 43880 standard - mounting in typical electro-installation unit,
●Rail mounting according to DIN35 / TS35 standard,
●Dimensions of casing contour (W x H x D) 71mm x 90mm x 58mm,
2.2. D SCRIPTION
Fiber Optic ADA-7200 repeater is a device that allows for extension of fiber optic networks to connect devices in places far away from
each other such as halls, buildings and other objects. Optic signal regeneration there is without interference of data format. The use of
fiber optics provides complete isolation between connected devices and resistance to interference on the transmission bus. The fiber
connection is implemented by a line consisting of two fibers. Using ADA-7200 extend fiber optic bus by a distance 2500m.
ADA-7200 repeater transmits and receives data at speeds up to 5Mbps through two multimode optical fiber in full duplex mode or half
duplex mode. The converter is equipped with screw terminal block for power connections. It is possible to extend the bus by any
number repeaters.
Fig. 1. View of ADA-7200
2.3. ISOLATION
Converter ADA-7200 has galvanic isolation between power circuit and Fiber Optic interface on the level 1kV= or 3kV=, depend on
version described in section VERSIONS.
Fig. 2. Isolation structure.
4
ADA-7200
Power Supply
10 - 30 VDC
90mm
71mm
10mm
58mm
TX 1
RX 2
RX 1
TX 2
Vss - Vss +
ADA-7200
PWR
COM
FIBER OPTIC REPEATER
Power Supply
10 - 30VDC
Fiber Optic
ISOLATION
Fiber Optic

3. INSTALLATION
This chapter will show how to connect ADA-7200 to Fibre-Optic and power supply and how to use it.
3.1. CONN CTION FIBR -OPTIC BUS
The multimode Fibre-Optic with connectors type: ST®, SC or SMA, connect into their corresponding converter's connectors type: ST®,
SC or SMA like on the figure below. Connecting the fiber optic cables should be cautious and careful not to damage them or dirty. If it
is necessary to lay the cable at an angle, must be created the appropriate bends.
ATT NTION!!!
The device is equipped in the laser transmitter.
The radiation emitted by the laser transmitter is harmful to the eyes!
Under no circumstances should never look to at the uncovered slot, to which it is not connected the fiber optic
connector.
3.2. WIRING TOPOLOGY FIB R OPTIC BUS
Fig. 3. xamples of fiber optic bus connection.
5
ADA-7200
RS-232
ADA-7010
closing
ADA-7240
Multidrop
RS-422/485
Controller 1
RS-232 PC
Fiber Optic bus
2 fibres 50/125um or 62.5/125
PC
ADA-7200
Multidrop
ADA-7210
Multidrop
ADA-7010
closing
RS-232
Controller 2

3.3. XAMPL S OF CONN CTION TH CONV RT R TO FIB R OPTIC BUS
Fig. 4. xample connection of ADA-7200 to fiber optic bus
6
ADA-7200
ADA-7010
FO
connector
TX
RX
RX
DSR
DTR
RTS
CTS
TX
V (+)
V (-)
PC
RS232
connector
RX
DSR
DTR
RTS
CTS
TX
ADA-7020
Current loop
connector
FO
Conn.
TX
RX
V (+)
TX-
TX+
RX+
RX-
V (-)
Controller
Current loop
connector
V (+)
TX-
TX+
RX+
RX-
V (-)
ADA-7240
RS485
connector
FO
connector
TX1
RX1
TX2
RX2
V (+)
TX-/B
TX+/A
RX+
RX-
V (-)
V +
V -
Power Supply
ADA-7200
FO
connector
TX1
RX1
TX2
RX2
V (+)
V (-)
V +
V -
Power Supply
RS232
connector

3.4. POW R SUPPLY CONN CTION
The power supply to the ADA-7200 repeater should be DC (regulated) from 10 V= to 30V=. Nominal power is typically 3W, e.g. ZS-
12/250 or DR-15-24. Power cable from DC power supplies to device must not be longer than 3m.
Observe the polarity, connect positive (+) of DC power supplies to V+ and negative (-) end to V- screw terminal block. ADA-7200 has
the protection from opposite connection power supply. If after power, on the front panel is not lit green LED PWR, check the power
connection (polarity).
4. ACTIVATION
The converter can be power on after properly connection according to section above.
If after connection power supply on front panel will not light green led PWR, check correctness of power supply connecting
(polarization). When data is present the LEDs COM should blink.
4.1. D SCRIPTION OF SIGNALLING L DS
LED Description
PWR Signalling of Power Supply
COM Signalling of data transmission
ATT NTION!
AT BAUD RAT ABOV 38.4 KBPS TH L D'S TX, RX WILL LIGHT W AKLY DURING DATA TRANSMISSION
5. V RSIONS
ADA-7200 - - -
Order example:
Product symbol: ADA-7200-2-3-1
2 - galvanic isolation 1kV=,
3 – cover without inlets, plug-in screw terminal block,
1 – ST-type 850nm fibre connectors,
Galvanic isolation:
1kV= 2
3kV= 3
Terminal & Terminal Cover:
Cover without inlets, screw terminal block 1
Cover with inlets, screw terminal block 2
Cover without inlets, plug-in screw terminal block 3
Fibre connectors:
ST – type 850nm 1
SC – type 850nm 2
SMA – type 650nm 3
6. SP CIFICATION
T CHNICAL DATA
Transmission Parameters
Fibre-Optic interface
ST® * type - transmitter and receiver for an optical wavelength from 792nm to
865nm,
SC type - transmitter and receiver for an optical wavelength from 792nm to 865nm,
SMA type - transmitter and receiver for an optical wavelength from 640nm to 675nm.
Line length
up to 2000m for fibre type 50/125 mm,
up to 2500m for fibre type 62,5/125 mm
up to 2000m for fibre type 100/140 mm
up to 20m for fibre type POF/1mm
Max. number of connected device Free
Max. baud rate
up to 5MBd for fibre type 50/125 mm,
up to 5MBd for fibre type 62,5/125 mm
up to 5MBd for fibre type 100/140 mm
up to 2MBd for fibre type POF/1mm
Transmission line
Two multimode fibres:
- connectors ST-850, fibres type 50/125 mm,62,5/125 mm, 100/140mm, 200mm HCS.
- connectors SC-850 fibres type 50/125 mm, 62,5/125 mm, 100/140mm, 200mm HCS.
- connectors SMA-650 plastic fibres type POF/1mm.
7
ADA-7200

Transmission type Asynchronism full duplex, half duplex.
Optical signalisation •PWR – green LED power supply,
•COM - yellow LED data transmission
lectrical Parameters
Power requirements 10 - 24 – 30 V DC
Power Cable Recommended length of power cable – up to 3m.
Power 3 W
Protection from reverse power polarization YES
Galvanic Isolation 1kV DC or 3kV DC between power supply and Fiber Optics
lectromagnetic compatibility Resistance to disruptions according to the standard PN-EN 55024.
Emission of disruptions according to the standard PN-EN 55022.
Safety requiring According to the PN-EN60950 norm.
nvironment Commercial and light industrial.
nvironmental Parameters
Operating temperature -30°C ÷ 60°C
Humidity 5 ÷ 95% - non-condensing
Storage temperature -40 ÷ 70 °C
Casing
Dimensions 71 x 90 x 58 mm
Material PC/ABS
Degree of casing protection IP40
Degree of terminal protection IP20
Weight 0,10 kg
According to standard DIN EN50022, DIN EN43880
Location during work Free
Mounting method On the rail compliant with DIN35 / TS35 standard.
* ST is a trademark of AT&T.
8
ADA-7200
Dear Customer,
Thank you for purchasing C L-MAR Company products.
We hope that this user manual helped connect and start up ADA-7200 repeater. We also wish to inform you that we are a
manufacturer of the widest selections of data communications products in the world such as: data transmission converters with
interface RS232, RS485, RS422, USB, Current Loop, Fibre-Optic Converters and Ethernet or Wi-Fi.
Please contact us to tell how you like our products and how we can satisfy you present and future expectation.
C L-MAR sp.j.
Zakład Informatyki i Elektroniki
Sciegiennego 219C str.
25-116 Kielce, POLAND
Tel....................................................: [phone]
Tel/fax.............................................. : [phone]
Web................................................. : http://www.cel-mar.pl/en
Office............................................... : [e-mail]
Sales department........................... .: sa l es @cel-mar.pl
Technical information ..................... : [e-mail]