Celabs HA8-3 User manual

HDMI Distribution
Amplifier
Model HA8-3
CE labs can support many areas of your audio and video
distribution needs.
We manufacture:
• Digital Signage software and Media Players
• HD Matrix Switchers
• RF amplifiers
• HDMI and Component HD distribution amplifiers
• CAT 5 Signal Extenders
• VGA Extenders and Splitters
• and cables of all types.
See our full product line at www.celabs.net
WARRANTY
Cable Electronics, Inc. warrants this product to be free from defects in
material and workmanship, under normal use and service, for a period of
one year from the purchase by the original purchaser. If this product is
defective or malfunctions, Cable Electronics will replace or repair this unit
(at their option) within a reasonable time. No expressed or implied warranty
is made for any defects caused by immersion or exposure to liquids, abuse,
neglect, improper operation of unit, excess wear and tear and defects
resulting from unauthorized disassembly and or modification.
Document: HA8-3_Manual.pdf
930_2210_02_Rev.A
3209 Wood Drive
Garland, TX 75041
Phone: [phone]
Toll free: [phone]
Fax: [phone]
www.celabs.net
Integrated HCRS (HDMI Cable Retention System.) Prevents
accidental disconnectrs and service calls.
PanelLink digital technology
Supports HDTV resolutions 480i, 480P, 720P, 1080i, & 1080P
Cascadable for larger display systems.
Heavy duty metal housing. Commercial duty rated.
LAUNAMNOITCURTSNI

Pin # Signal Pin # Signal
1 TMDS Data 2+ 11 TMDS Clock Shield
2 TMDS Data 2 Shield 12 TMDS Clock -
3 TMDS Data 2- 13 CEC
4 TMDS Data 1+ 14 Reserved (N.C )
5 TMDS Data 1 Shield 15 SCL
6 TMDS Data 1- 16 SDA
7 TMDS Data 0+ 17 DDC/CEC Ground
8 TMDS Data 0 Shield 18 +5 Power
9 TMDS Data 0- 19 Hot Plug Detect
10 TMDS Clock+
NOTES:
1. All monitors connected to the distribution amplifier should be capable of the same resolution.
2. Always connect the first monitor to output number one on the Distribution Amplifier first.
This is necessary for the Electronic ID to be read properly by the source.
3. For optimum performance try to use HDMI cables no longer than 5 meters in length.
1. Turn off the devices to be connected together.
2. Connect the HDMI cable between the source (DVD, Satellite Receiver, etc.)
and the “HDMI In” port of the Distribution Amplifier.
3. Connect the HDMI cables from the outputs of the distribution amplifier to the
inputs of the monitors.
4. Power up the Distribution Amplifier and the Monitor connected to HDMI
output number one on the amplifier.
Leave the other monitors off for now.
5.Turn on power to the source device. The monitor connected to output
number one should have picture and sound within about 5 seconds.
6. Turn on power to the remaining monitors.
7. Install cable ties through the two holes on either side of the cable if desired to
prevent accidental unplugginf of the HDMI cables. See picture above.
1
2
3
4
5 6
Input
7 8
DC IN
HDMI SOURCE OUT 1
HDMI Distribution Amplifiers Cascade Configuration
SPECIFICATIONS
1
2
3
4
5 6
Input
7 8
DC IN
1
2
3
4
5 6
Input
7 8
DC IN
HA8 - 3 Units may be cascaded 7 layers deep.
HD MONITOR
#1
HA 8-3 HD MONITOR
#7
HD MONITOR
#8
HD MONITOR
#14
HD MONITOR
#15
HD MONITOR
#21
Model HA8-3
Input HDMI Connector (A-Type Female) 1
Output HDMI Connector (A-Type Female) 8
Max. Resolution 1080P
Cable Distance 10 m (Max.)
Signal Type HDMI V1.3b compliant
Power Adapter (Min.) DC 5V 4A
Housing Metal
Weight (3.5 lbs.) 1.5 Kg
Dimensions (LxWxH) mm 15” x 1.5” x 6.8”
HA 8-3
HA 8-3
Use these holes to secure
the HDMI cables withacable tie.
INSTALLATION/OPERATION INSTRUCTIONS