Celabs HM41SR User manual

HDMI Selector
HM41SR
Document: HM41SR_manual.pdf
930-3003-01
PACKAGE CONTENTS:
• 1 HM41SR HDMI Selector
• 1 user manual
• 1 power adapter DC 12V 600mA
• 1 remote control
• 1 RS-232 1.8M cable (DB-9 Male to Female)
• 1 RS-232 control software CD
INSTRUCTION MANUAL
3209 Wood Drive
Garland, TX 75041
Phone: [phone]
Toll free: [phone]
Fax: [phone]
www.celabs.net
WARRANTY
Cable Electronics, Inc. warrants this product to be free from defects in
material and workmanship, under normal use and service, for a period of
one year from the purchase by the original purchaser. If this product is
defective or malfunctions, Cable Electronics will replace or repair this unit (at
their option) within a reasonable time. No expressed or implied warranty is
made for any defects caused by immersion or exposure to liquids, abuse,
neglect, improper operation of unit, excess wear and tear and defects
resulting from unauthorized disassembly and or modification.

INSTALLATION
Before installation, make certain the selector and monitor are off:
1. Make sure all equipment is turned off.
2. Plug the monitor cable into HDMI OUT port connector.
3. Plug the extension cables from the HDMI port of the sources into the
HDMI IN port connectors.
4. Plug the power adapter into the wall socket.
5. Connect the power adapter to teh HDMI selector.
6. All red LEDs will flash back and forth, otherwise, go back to check
steps 4 and 5.
7. Turn the monitor on first.
8. Turn on the sources.
9. The LEDs will turn green when the sources are connected and
activated properly.
RS-232 CONTROL SOFTWARE INSTALLATION
1. Install the application program DHR Matrix.msi.
(Note: This program has to be run only in Windows.)
2. Connect the RS-232 Cable, the PC end is RS-232 port (COM-X)
while the HDMI selector end is the RS-232 port.
3. Power on the HDMI selector and run HDRM.exe. Select the COM
port.
4. Use Scan function to open the HDMI selector.
5. Select the Video and Audio to change port.
OPERATION
1. Port selection
• Press the button above the port number for accessing the
desired DVD player/TV receiver.
• The selected corresponding port will light the red LED
indicating the port is active.
2. IR remote control
• Press the number key on the remote of the input you wish
to view
• Use key to select another DVD player/TV receiver.
• Use key to power on/off selector.
• Use key to power on/off selecto
SPECIFICATIONS
HDMI Input Connector
(A-Type Female): 4
HDMI Output Connector
(A-Type Female): 1
LEDS:
Online 4
Selected 4
Select Switch: 4
RS-232 Connector: 1 x DB-9 Female
Max. Resolution: UXGA, 1080p
Power Adapter (Min.): DC 12V 600mA
Housing: Metal
Weight: 585 g
Dimensions (LxWxH) mm: 200x78x46
FEATURES
• HDTV resolution up to 1080p, PC resolution up to 1600x1200 60Hz
• Compliant with the specification of HDMI 1.2.
• Suport RS-232 control.
• IR controller for remote operation.
• Hot pluggable.
• Auto skips over the power-off and unplugged units.
HARDWARE REQUIREMENTS
HDTV: One LCD, PLASMA TV or projector with HDMI
input connector
DVD Player/
TV Receiver: HDMI output connector
Cable: HDMI male to male standard cable
FRONT VIEW REAR VIEW
1. Port selection switches (Manual type)
2. Port LEDs
• All the red LEDs flash while the power
adapter is properly connected
• Green LEDs light up while the ources
are properly connected and operating
• The top red LEDs light up while the source
has been selected
3. IR Receiver
• Direct the remote control at the IR
picup on the right side of the selector
1. Power supply.
Plug the DCBV 600mA power adapter here.
2. RS-232 Port Connector
Plug the RS-232 cable there for remote PC
control (Optional)
3. HDMI OUT port connector
Connect a HDMI cable from this port to the
HD monitor
4. HDMI IN port connectors
Plug the HDMI cables from the sources to the
four input ports.