Celco Spider67 User guide

Spider67 I/O Module
----Profinet System Manual
ELCO (Tianjin) Electronics Co., Ltd
04/2019
Version 1.5

Spider67 Profinet–Extensible industrial fieldbus I/O System 2 / 62
Preface
1. Scope of this manual:
This manual applies to the ELCO Profinet Spider67 distributed I/O device.
The information in this manual enables you to run the Spider67 module on
Profinet in a distributed I/O device.
2. Basic knowledge requirements
This manual presumes a general knowledge in the field of automation
engineering and describes the components based on the data valid at the time of
its release.
ELCO reserves the right of including a product information for each new
component, and for each component of a later version.
3. Guide
This manual describes the hardware of the Profinet Spider67 distributed I/O
device.
Covered topics are:
Installation and wiring
Commissioning and diagnostics
Components
Article numbers
Technical specifications
4. Technical support:
This manual describes the characteristics and the usage of a Spider67 distributed
I/O device.
Please contact your local ELCO representative or dial 400-608-4005 if you have
any questions about the products described in this manual.
Additional information about ELCO products is available:
http://www.elco-holding.com/
5. Disclaimer of liability:
We have reviewed the contents of this publication to ensure consistency with the
hardware and software described. Since variance cannot be precluded entirely,
we cannot guarantee full consistency. However, the information in this
publication is reviewed regularly and any necessary corrections are included in
subsequent editions.

Spider67 Profinet–Extensible industrial fieldbus I/O System 3 / 62
CONTENTS
PREFACE .................................................................................................................................2
1. PRODUCT OVERVIEW....................................................................................................5
1.1 Introduction .................................................................................................................................5
1.2 Applications .................................................................................................................................5
1.3 Features .......................................................................................................................................5
1.4 Type .............................................................................................................................................6
2. TECHNICAL CHARACTERISTICS.................................................................................8
2.1 Gateway.......................................................................................................................................8
2.2 I/O module...................................................................................................................................9
2.3 Extension cable ..........................................................................................................................10
2.4 Hardware ...................................................................................................................................11
2.4.1 Technical data of gateway ........................................................................................................11
2.4.2 Digital IO Module......................................................................................................................12
2.4.3 Analog IO Module.....................................................................................................................13
2.4.4 RTD and TC Module ..................................................................................................................14
2.5 LED display.................................................................................................................................15
3. INSTALLING.................................................................................................................... 17
3.1 Mounting dimensions ................................................................................................................17
3.1.1 Gateway dimensions ................................................................................................................17
3.1.2 Module dimensions ..................................................................................................................18
3.2 Mounting position and dimensions............................................................................................19
3.3 Assigning names in PROFINET IO devices ...................................................................................20
3.3.1 Assigning names by Step7 ........................................................................................................20
3.3.2 Assigning names by Portal........................................................................................................21
3.4 Wiring Spider67..........................................................................................................................23
3.4.1 Connecting Spider67 to protective earth (PE) .........................................................................23

Spider67 Profinet–Extensible industrial fieldbus I/O System 4 / 62
3.4.2 Spider67 power supply.............................................................................................................23
3.4.3 Spider67 BUS connection .........................................................................................................25
3.4.4 Spider67 digital signal connection ...........................................................................................26
3.4.5 Spider67 analog signal..............................................................................................................29
4.1 Installation of configuration files................................................................................................33
4.2 Signal address assignment..........................................................................................................35
4.3 Instruction of Analog Value ........................................................................................................38
4.4 Module Startup Process .............................................................................................................43
4.5 Module configuration by Step7 ..................................................................................................44
4.6 Module configuration by Portal..................................................................................................52
5. ALARM DIAGNOSIS...................................................................................................... 59
5.1 LED fault indicator......................................................................................................................59
5.2 Diagnostic information...............................................................................................................61

Spider67 Profinet–Extensible industrial fieldbus I/O System 5 / 62
1. Product overview
1.1 Introduction
Spider67 from ELCO supports modern installation methods with a new and
revolutionary expandable I/O system. The simple and easy to install Fieldbus
system Spider67 is especially suitable for applications in rough environments.
1.2 Applications
Recently, the wide-range usage of industrial fieldbus I/O products brought deep
impact to the automation industry. The traditional centralized control method
was replaced by intelligent distribution devices. Besides that, more devices were
transferred from cabinets directly to the site. Therefore the reason lies in saving
costs, reducing the operation time and shorten the maintenance period. It also
optimizes the system procedure.
ELCO Spider67 exactly complies this tendency and represents a revolutionary
new generation of I/O solutions. Spider67 is an expandable industrial fieldbus I/O
product with protection class IP67. It supports standard industrial bus protocol
gateways (such as Profibus-DP, Profinet, EtherCAT, CC-Link) and diversified
extended I/O configuration modules and can easily be connected to PLC systems.
Compared to the traditional IP67 I/O products, Spider67 expanded modules
include digital modules, analog modules and high-speed counting modules etc.
Regarding its functions, Spider67 can meet most of the requirements, e.g.
processing concentrated / dispersed switch signals etc. At the same time, this
product series offers flexible connection cable and can directly be mounted on a
cage lifter or rotational device.
1.3 Features
IP67 protection class leading to convenient mounting
Compact design minimizes mounting space requirement
Standard connection, fast, safe and reliable
Various input and output signals
Flexible I/O configuration with a combination of analog, digital, and function
modules
LED status indication, fast function diagnosis
Can be combined with Spider67 system at random

Spider67 Profinet–Extensible industrial fieldbus I/O System 6 / 62
1.4 Type
No.
Type
Description
1
SPPN-GW-001
Profinet substation interface module
1 male 7/8”power supply
2 female, M12 D-Code fieldbus interface
4 female, M12 B-Code extended interface
2
SPDB-0800D-001
SPDB-0800D-003
8 PNP/NPN switches or dry contact
4-female, M12 A-Code interface
3
SPDB-0800D-011
SPDB-0800D-013
8 PNP/NPN switches or dry contact
8-female, M8 interface, 3-pin
4
SPDB-0404D-001
SPDB-0404D-003
4 PNP/NPN switches or dry contact
4DI4DO, 0.5A each channel
4-female, M12 A-Code interface
5
SPDB-0404D-011
SPDB-0404D-013
4 PNP/NPN switches or dry contact
4DI4DO, 0.5A each channel
8-female, M8 interface, 3-pin
6
SPDB-08UP-001
8DI+DO, configurable
4-female, M12 A-Code interface
7
SPDB-08UP-011
8DI+DO, configurable
8-female, M8 interface, 3-pin
8
SPDB-0008D-001
8DO, 0.5A each channel
4-female, M12 A-Code interface
9
SPDB-0008D-011
8DO, 0.5A each channel
8-female, M8 interface, 3-pin
10
SPDB-0006D-001
8DO, 2A each channel
1-male, M12 A-Code interface
3-female,M12 A-Code interface
11
SPDB-0300A-001
3AI
0~20mA, 4~20mA, ±20mA optional
3-female, M12 A-Code interface
12
SPDB-0300A-002
3AI
0~10V, ±10V optional
3-female, M12 A-Code interface

Spider67 Profinet–Extensible industrial fieldbus I/O System 7 / 62
13
SPDB-0003A-001
3AO
0~20mA, 4~20mA, ±20mA optional
3-female, M12 A-Code interface
14
SPDB-0003A-002
3AO
0~10V, ±10V optional
3-female, M12 A-Code interface
15
SPDB-0400A-005
4AI RTD
PT100，PT200，PT500，PT1000，Ni100，
Ni1000，150/300/600/3000Ω
4-female, M12 A-Code interface
16
SPDB-0400A-006
4AI Thermocouple
B，E，J，K，N，R，S，T
4-female, M12 A-Code interface
17
BB6S30P01Dxxx
BB6S30P01Mxxx
Pre-wired extensible cable
PVC, 5-core shielded, outer diameter 6.5mm
Customized length, D=cm，M=dm
18
BB6S30P03Dxxx
BB6S30P03Mxxx
Pre-wired extensible cable（drag chain）
PUR, 5-core shielded, outer diameter 6.5mm
Customized length, D=cm，M=dm
19
BB6S30P09Dxxx
BB6S30P09Mxxx
Pre-wired extensible cable（long distance
communication）
PVC, 5-core shielded, outer diameter 8mm
Customized length, D=cm，M=dm
20
BB6S06
Extension terminal resistance
Connecting to the last I/O module

Spider67 Profinet– Extensible industrial fieldbus I/O System 8 / 62
2. Technical characteristics
2.1 Gateway
The following picture is the schemac of Spider67 gateway.
Each gateway occupies one sub-staon address, maximum 4 strings, up to 6 I/O
modules / string, extending distance up to 100 m.
In order to achieve the PROFINET network communicaon requirements based on
the industrial Ethernet, Spider67 gateway, as the slave staon of PROFINET, can
assign the device name and the corresponding IP address via the configuraon tool,
it also can automacally assign IP addresses by PLC according to the network
topology. Each Spider67 gateway can connect up to 24 I/O modules via extended
port; sort the modules for 1~24 according to the sequence of the connected
extension port and the gateway distance from near to far, and configure in
programming soware Step7(see secon 4.4). If the module is connected to the
extended port not up to 6, then the number of the following module will be moved
Power interface:
24VDC, 2 independent power supply
Power supply for system and extensible module
Extension interface
4×M12，6 for each interface
Seng/Display
Set address and rate
Display operang status and fault message
Communicaon interface
Standard interface based on different protocols

Spider67 Profinet–Extensible industrial fieldbus I/O System 9 / 62
ahead, such as P0 port connect 3 modules, then the serial number of the first
module of P1 port is 4, by analogy, the serial number is the module number that you
connected.
2.2 I/O module
The picture is the schematic of a Spider67 I/O module.
I/O modules of Spider67 are serial connected, and are connected to In of 1st module
by extension cable, then Out of 1st module to In of 2nd, up to 6 modules.
Spider67 I/O modules are designed by the same housing dimensions, including
digital, analog, input and output, only 2 different interfaces, 4-M12 and 8-M8. M12
A-Code, 2 digital or 1 analog are available. M8, 3-pin, 1 digital is available.
Extension interface
In/out, serial
1 cable for communication and power supply
I/O interface:
4×M12
8×M8

Spider67 Profinet–Extensible industrial fieldbus I/O System 10 / 62
2.3 Extension cable
Spider67 extension cable is used between gateways and I/O modules. The overall
cable length from the extension interface to the last module is less than 100m .
P01 series cable is the standard extension cable. P09 series long distance
communication cable is recommended if the extension distance is over 10m or
high load current, P03 series flexible communication cable is especially used for
bending lifespan like drag chain (see 1.4)
Terminal resistance is recommended to eliminate reflection and echo, which are
used to prevent discontinuous extensible cable resistance or interference caused
by long distance communication. As Spider67 is installed terminal resistance,
users need to connect a resistance to Out of the last module of each extension
interface.