Celestron StarSeeker 80mm User manual

Model #21072
F80 EQ WA 

80mm (3.1”)
REFRACTOR TELESCOPE
INSTRUCTION MANUAL

Figure 1

5
Tube Ring
Square
Extrusions Mounting
Platform
Knurled Screw (opposite of
tube ring hinge)
Finderscope
Finder Bracket
Focusing Set
Screw
Figure 2

6
1. INTRODUCTION
Thank you for purchasing this Celestron 80mm Refractor Equatorial Telescope. This telescope is a precision
scientific instrument. With it you will enjoy numerous objects in the sky—planets, nebulae, star clusters,
galaxies and other astronomical objects.
But, before your journey begins take time to read this manual to familiarize yourself with the operation and parts
of this telescope.
WARNING—NEVER LOOK AT THE SUN WITH YOUR TELESCOPE OR ITS FINDERSCOPE.
PERMANENT AND IRREVERSIBLE EYE DAMAGE MAY RESULT AS WELL AS DAMAGE TO
YOUR TELESCOPE.
HOWEVER, YOU MAY ENJOY LOOKING AT THE SUN IF YOU HAVE A SAFE METHOD
OF DOING SO—A SOLAR FILTER. IF USING A SOLAR FILTER, MAKE SURE THE
FINDERSCOPE IS COVERED.
2. TELESCOPE ASSEMBLY
Please refer to figures 1 and 2 (and the identifying parts list) as you assemble the telescope.
The telescope and all items are packed in one box. Included are:
•Telescope Optical Tube
•German Equatorial Mount
•Adjustable Wood Tripod
•Counterweight Shaft and Counterweight
•Tripod Accessory Tray
•Declination Cable
•Right Ascension Cable
•25mm SMA Eyepiece - 1¼” (16x)
•Diagonal - 1¼”
•Finderscope, 6x30
A. Locate the German equatorial mount and the tripod legs along with the tripod mounting hardware and the
tripod accessory tray.
1. Lie the tripod head (#7) on its side. Attach the three tripod legs (#12) one by one to the tripod head
with the bolts and wing nuts (#17). Do not over tighten the bolts but just make them lightly finger tight.
Remember to have each tripod leg in the right orientation with the tripod tray bracket (#11) facing
inward.
2. Next, put the bolts and wing nuts in the bottom of the tripod legs through the holes for the height
adjustment you want. We suggest you keep it at the lowest height for assembly (you can raise it later if
you wish) and for maximum rigidity. NOTE—this may have been assembled at the factory.
3. Now set the tripod with the equatorial mount attached in the standing position by spreading the legs
apart far enough for the tripod accessory tray (#11) to fit.
4. You are now ready to install the tripod accessory tray (#11). The tripod tray bracket fits into slots in the
bottom of the tray (use the holes on the ends of the brackets). Use the bolts and wing nuts to attach
each bracket to the tray.

7
5. Tighten all bolts and wing nuts to ensure proper stability.
B. Before proceeding further, locate knobs #19 and #16 and tighten them finger tight after orienting the
mount as illustrated in figure 1.
1. Locate the declination cable holder (where #21 fits on). Locate the declination cable (the shorter of the
two cables) and attach the cable (#21) to the cable holder by tightening the thumb screw on the cable
end. The thumb screw should be tightened down hard on the flat surface of the cable holder after
backing off the cable about 1/4" from being fully engaged. This method helps ensure there is no
slippage when using the cable.
2. You may reverse the position orientation of the Declination cable to suit your preference if desired.
3. Locate the right ascension cable holder (where #18 fits on). Locate the right ascension cable (#18) and
attach it the same way as the declination cable was attached in the last section.
4. Slide the counterweight shaft (#9) through the counterweight (#8). Use the counterweight lock (#10) to
lock the counterweight in place. By holding the counterweight in one hand, thread the counterweight
shaft clockwise into the equatorial mount as shown in figure 1.
C. You are now ready to put the telescope optical tube (#2) onto the equatorial mount (#6).
The optical tube is held to the mount with two mounting rings. On the bottom of the mounting rings are square
extrusions — one on each ring. This portion of the ring slides over the ends of the mounting platform to hold
the telescope in place (see figure 2).
1. Loosen the knurled screws on the side of the mounting rings and remove the tube ring closest to the focuser
end of the optical tube.
2. Slide the remaining tube ring towards the objective end of the telescope tube.
3. Place the telescope tube on the mounting platform and orient it so that the objective lens is opposite the
slow motion control handles.
4. Slide the attached tube ring down until the square extrusion fits over the end of the mounting platform.
5. Insert one of the mount platform screws through the bottom of the square extrusion and thread it into the
mount.
6. Open the second tube ring and place the square extrusion under the other end of the mounting platform.
7. Close the tube and slightly tighten the knurled screw to hold the tube ring in place.
8. Thread the second mounting screw through the square extrusion of the tube ring and into the mounting
platform. Tighten both mounting screws.
9. Tighten the knurled screws that clamp the mounting rings in place . This will keep the telescope from
sliding back and forth in the mounting rings.
D. Put the diagonal (#23) into the focuser (#22) and tighten the thumb screw on the focuser to hold it in
place.
E. Put the eyepiece (#1) into the diagonal and tighten the thumb screw to hold it in place.

8
3. TELESCOPE OPERATION -GETTING SET UP
A. Loosen the polar axis knob (near #5) with one hand while holding the equatorial mount with the other hand.
Look at the latitude scale (#19) and move the mount to the latitude of your location and then tighten the
polar axis knob. This only has to be done once unless you take the telescope to a different location. For
example, Los Angeles, California is located at about 34º. If you do not know your latitude, it can be found
on most road atlases of your area.
B. To change the direction your telescope is pointing:
1. To move the telescope in declination (north/south) there are two options. For large and quick
movements, release the declination knob (near #4) and then tighten the knob when you are near the
position you want. For very small movements and fine adjustments, use the declination cable (#21).
The declination cable has a range of about 30ºand if you come to the stop at the end then overshoot
your target by releasing the declination knob and move the telescope in declination. Then tighten the
knob and reverse the direction of the declination cable. Do not try to force movement when the
declination cable has reached the stop.
2. To move the telescope in right ascension (east/west) there are two options. For large and quick
movements, release the right ascension knob (near #5) and then tighten the knob when you are near the
position you want. For very small movements and fine adjustments, use the right ascension cable.
C. The telescope should be properly balanced in order for it to move smoothly in both axes. Proper balance is
essential if using an optional motor drive for accurate tracking.
1. To balance the right ascension axis, move the counterweight shaft so it is parallel (horizontal) to the
ground. Slowly release the right ascension knob (near #5) and see if the optical tube moves. If the
optical tube moves, then slide the counterweight up or down the counterweight shaft until the optical
tube remains stationary in the parallel position to the ground. When this happens, make sure the
counterweight lock is tight.
D. To quickly move the telescope around horizontally
1. Loosen the horizontal adjustment knob (#16), move the telescope to the position desired and then
tighten the knob.
E. To focus the telescope.
1. Remove the front lens cover (#3).
2. With a low power eyepiece tight in the diagonal (with its lens cover removed), position the telescope
tube to look at any object about one mile or further away during the day. You may need to use the
flexible cables to get the object in the center of the field. To focus, turn the focusing knob (#22) until
your chosen object is in sharp focus. Remember to use outdoors only as you should not look through
windows which may distort the image.
F. Attaching the Finderscope:
This telescope uses a 6x30 finderscope which is easily attached to the dovetail mount. To attach the
finderscope:
1. Attach the finderscope and bracket by sliding the rubber O-ring over the eyepiece end of the finderscope
and roll it 2/3 of the way up the finderscope. Then insert the eyepiece end of the finderscope through the
bracket until the O-ring presses tightly between the finder and the inside of the bracket. Tighten the three
adjustment screws until they make contact with the finderscope body.
2. Slide the finder bracket (attached to the finderscope) into the mounting bracket on the telescope. Tighten
the set screw on the mounting bracket to hold the finderscope in place (see figure 3).

9
G. Aligning the Finderscope:
Do not be alarmed when you look through the telescope and the object is upside down and reversed left to
right. This is normal with an astronomical telescope. To align it:
1. Choose a target in excess of one mile away. This will eliminate any possible parallax effect.
2. Point the F80 EQ at your target and center it in the main optics of the telescope.
3. Adjust the screws on the finder bracket until the cross hairs in the finder are centered on the target.
4. Tighten each screw a quarter of a turn so they will not come loose.
H. Preparation for astronomical observing requires that you:
1. Orient the telescope so that the right ascension (polar) axis is pointing as close to true north as possible.
Use a magnetic compass if you are not sure which way north is.
2. Make sure the mount is level. A carpenters level may be helpful.
3. Recheck all hardware and knobs to make sure all are tight.
4. UNDERSTANDING THE SKY
A. The Celestial - Coordinate System.
The celestial-coordinate system is an imaginary projection of the Earth's geographical coordinate system
onto the celestial sphere which seems to turn overhead at night. This celestial grid is complete with equator,
latitudes, longitudes and poles.
The Earth is in constant motion as it rotates on its axis. Actually the celestial-coordinate system is being
displaced very slowly with respect to the stars. This is called precession and is caused by gravitational
influences from the Sun, Moon and other celestial bodies.
The celestial equator is a full 360º circle bisecting the celestial sphere into the northern celestial hemisphere
and the southern celestial hemisphere Like the Earth's equator, it is the prime parallel of latitude and is
designated 0º.
Figure 3

10
The celestial parallels of latitude are called "coordinates of declination (Dec.)", and like the Earth's latitudes
they are named for their angular distances from the equator. These distances are measured in degrees,
minutes and seconds of arc. There are 60 minutes of arc in each degree, and 60 seconds of arc in each arc
minute. Declinations north of the celestial equator are "+" and declinations south are "-". The north pole is
+90 and the south pole is -90 .
The celestial meridians of longitude are called
"coordinates of right ascension (R.A.)", and like
the Earth's longitude meridians they extend from
pole to pole. There are 24 major R.A.
coordinates, evenly spaced around the 360º
equator, one every 15º. Like the Earth's
longitudes, R.A. coordinates are a measure of
time as well as angular distance. We speak of the
Earth's major longitude meridians as being
separated by one hour of time because the Earth
rotates once every 24 hours (one hour = 15°).
The same principle applies to celestial longitudes
since the celestial sphere appears to rotate once
every 24 hours. Right ascension hours are also
divided into minutes of arc and seconds of arc,
with each hour having 60 minutes of arc and each
arc minute being divided into 60 arc seconds.
Astronomers prefer the time designation for R.A.
coordinates even though the coordinates denote
locations on the celestial sphere, because this
makes it easier to tell how long it will be before a
particular star will cross a particular north-south
line in the sky. So, R.A. coordinates are marked off in units of time eastward from an arbitrary point on the
celestial equator in the constellation Pisces. The prime R.A. coordinate which passes through this point is
designated "O hours O minutes O seconds". We call this reference point the vernal equinox where it
crosses the celestial equator. All other coordinates are names for the number of hours, minutes and seconds
that they lag behind this coordinate after it passes overhead moving westward.
Given the celestial coordinate system, it now becomes possible to find celestial objects by translating their
celestial coordinates using telescope pointing positions. For this you use setting circles for R.A. and Dec. to
find celestial coordinates for stellar objects which are given in star charts and reference books.
B. Polar Alignment
To make tracking the stars easier, rough polar alignment is required.
1. The right ascension (polar) axis should be pointed towards the North Pole (see the illustration below).
2. The equatorial mount should be level.
3. Your latitude should be set (see section 3.A).
Figure 4

11
Figure 5
4. See the illustration below if you are not sure where the North Pole is located.
Figure 6
5. To find astronomical objects, you will now mainly use the right ascension axis as the polar alignment
virtually eliminates needed adjustments in the declination axis.
To track objects continuously, adjustments will be made with the right ascension cable. If you use an
optional motor drive (this moves at the same rate as the Earth rotates), it will automatically track the
objects for you.
So, if using a motor drive, the objects observed through the telescope appear stationary (they do not
drift out of the field of view). When using the basic telescope, all objects in the sky will slowly drift
out of the field of view unless you manually make corrections with the right ascension cable.

12
6. The above method of polar alignment is adequate for casual observing. More precise methods of polar
alignment are available and most astronomy texts or telescope books describe the procedures.
7. If you look at the North Star after this polar alignment procedure, your declination setting circle (#8)
should read 90°(the actual is 89.2°).
C. Using the Setting Circles
Setting Circles are dials (or gauges) for right ascension and declination that allow you to locate celestial
objects easily from their coordinates as listed in a star chart or atlas.
1. The declination setting circle is scaled in degrees and the right ascension setting circle is incremented
in minutes. The circles will get you close to your target but not directly on it. Also, the accuracy of
your polar alignment will affect how accurate your setting circles read.
2. The declination setting circle is factory set and should not need any adjustment if it reads accurately as
noted in 4.B (7).
3. The right ascension setting circle (#5) must be aligned. Choose a bright and easy to find star in a star
chart and note the coordinates (right ascension and declination). Find the star and center it in the
finderscope and then in the telescope. Now, rotate the right ascension circle to match the coordinates
of the star with the indicator mark.
4. The right ascension setting circle does not move as the telescope moves in right ascension and thus it
must by aligned each time you want to use it to find a new object. However, you do not need to use a
bright star each time but you can use the object you are currently observing.
5. Now, using a star chart or atlas you can find numerous objects. First move the telescope in declination
to the correct declination coordinate. Then move the telescope in right ascension until the indicator
points to the correct coordinate.
6. After moving the telescope to the correct celestial coordinates, look through the finderscope to see if
you have located the object and center the object. Then, look through the telescope (with a low power
eyepiece) and the object should be there.
On fainter objects, they may not be visible in the finderscope and thus you should gradually sweep the
telescope around (with the right ascension and declination cables) until the object is visible.
5. MAGNIFICATION (POWER)
The magnification (or power) of a telescope is variable depending upon the focal length of the eyepiece
being used along with the focal length of the telescope.
A. Your telescope has a focal length of 400mm.
To calculate the magnification we use the following formula:
Magnification FL telescope
FL eyepiece
=()
()
where FL(telescope) is the focal length of the telescope and FL(eyepiece) is the focal length of the eyepiece.
So, if you use a 25mm eyepiece your magnification is 400/25 = 16x.

13
There are numerous optional eyepieces that are available to expand your range of magnification. There are
various types of eyepieces of varying quality to choose from.
B. Magnification through the telescope has its limits. These limits are determined by the laws of optics and the
nature of the human eye. The maximum usable power is equal to 60 times the aperture of the telescope (in
inches). So your telescope has a maximum useful power of 189x (3.15" x 60). You can create power
higher than this limit but the images will be dark and blurred.
The maximum power is used only under ideal conditions which are not common. Most of your viewing will
be done in the range of 15x to 140x. Higher powers are used mainly for lunar and planetary observing.
C. Your telescope also can use an optional 2x Barlow Lens - 1¼”. The Barlow Lens doubles the power of any
1¼” eyepiece that you use.
1. To use the Barlow Lens, insert the chrome barrel end of the Barlow lens into the diagonal and secure
with the thumb screw. Then insert the eyepiece in the other end of the Barlow Lens and tighten the
thumb screw. This will yield a 2x power gain.
6. TELESCOPE OPERATION — ASTRONOMICAL OBSERVING
After you have read and followed the instruction manual to this point, the telescope is set up and you are ready
to begin your observing adventure.
To enable you to find objects you should have a set of Star Charts. The location of the planets may appear in
local newspapers.
A. The Moon is an awesome first object to observe. The best observing occurs during the partial phases as a
full Moon is too bright.
At low power you can see the complete Moon and at high powers you can see lunar details such as mountain
ranges, crates and rills.
B. Five of the planets are easy targets for your telescope.
See Jupiter with its great red spot, study the cloud bands and watch its moons shuttle back and forth.
Study Saturn and its splendid ring structure.
Observe Mars and see its polar cap.
Watch Venus and Mercury as they go through their moon-like phases.
C. The Sun is quite safe to view if you utilize a proper solar filter. You can detect and watch the ever-
changing sunspot activity.
Remember to cover the finderscope when using a solar filter.
D. Deep-Sky objects (those outside our solar system) offer a lifetime of observing. There are hundreds of
objects within the realm of your telescope including open and closed star clusters, planetary and diffuse
nebulae, galaxies, double stars and occasional comets.
The amount of detail you can see is dependent on your observing site (dark sky rural locations are best),
atmospheric conditions, brightness of the object, collimation and your observing experience.

14
7. Photography
Your 80mm EQ can be used photographically as well as visually. To turn your telescope into a telephoto
lens all you need is to use the built-in T-Adapter and a T-Ring designed for your particular camera make
(i.e., Nikon, Minolta, Pentax, etc.). The T-Ring, which replaces the camera’s normal lens, threads onto the
T-Adapter.
A. To attach a camera to your 80mm EQ:
1. Remove all the visual accessories from your telescope.
2. Thread the T-Ring onto the built-in T-Adapter threads until tight.
3. Couple the camera body to the T-Ring the way you would to any other lens.
B. Focusing the Camera
Once you have selected a target and centered it, turn the focusing knob until you achieve the sharpest
possible focus. (The focusing mechanism is the same photographically and visually.) Once the camera
has been focused, tighten the focusing set screw to secure the focus point. This will prevent the weight of
the camera from pulling the focus tube out further, thus changing the true focus.
Due to the high magnification of the camera/telescope combination, the micro prism focuser in your
camera may “black out.” If this is the case, you will have to use the ground glass portion of your focusing
screen, which itself may be dark. For the best results, take your time. Look at your subject carefully to
make sure that you have the sharpest possible focus. To achieve a very sharp focus, consider using a
focusing magnifier. These devices are readily available from your local camera store.
8. TELESCOPE MAINTENANCE
With proper care your telescope should rarely need any maintenance work.
A. When not in use, always replace all lens covers to keep dust and contaminants off the optical
surfaces.
B. A small amount of dust on any optical surface is ok. If the dust builds up then use a can of
compressed air and then a camel's hair brush to remove the dust.
C. If the objective lens (internally) needs cleaning, it should be cleaned by a professional. Either have your
instrument serviced by a telescope repair facility or return it to the factory.
Figure 7

15
D. To clean the outside of the objective lens, you may use an optical lens cleaning kit (available at most photo
stores) or the Celestron LensPen (#93575) cleaning tool.
SPECIFICATIONS AND STANDARD ACCESSORIES
Model #21072
Optical System: Refractor
Aperture: 80mm
Focal Length: 400mm
F/ratio: f/5
Focuser 1¼" Rack and Pinion
Standard Ocular 25mm 1¼” eyepiece
Magnification with standard eyepieces 16x
Highest Useful Power Magnification: 189x
NOTE: Specifications are subject to change without notice.
9. OPTIONAL ACCESSORIES
Celestron International offers a wide assortment of optional accessories to expand your interests.
A. Sky Maps (#93722) - Invaluable when learning the night sky. They include all the constellations with the
brighter deep-sky objects. On the front cover is a rotating planisphere which indicates when specific
constellations are visible.
B. Flashlight - LED (#93588) - Uses a red LED to allow reading star maps and locating telescope accessories
and controls without ruining you night vision.
C. Eyepieces - A whole assortment of 1¼" eyepieces are available to give you a wide range of magnifications.
D. A 1¼" Standard 2x Barlow Lens (#93507) is available as well as a deluxe 2x model (#93506).
E. Erect Image Diagonals Mainly used for terrestrial applications where the correct image is seen (you see
through the telescope exactly what you see with your eye). A 45ºmodel is available (#94112-A) as well as
a 90ºmodel (#94108).
F. Planisphere & Planet Guide (#93720) Simple and easy to use to find your way around the sky. Available
in various latitude ranges 30º (20 – 40º), 40º (30 – 50º), 50º (40 – 60º).
G. Other accessories are available. See the Celestron Accessory Catalog (#93685) or ask your Celestron
dealer for details.

16
CELESTRON ONE YEAR LIMITED WARRANTY
A. Celestron International (CI) warrants this telescope to be free from defects in materials and workmanship for one year from the date of
purchase. CI will repair or replace such product or part thereof which, upon inspection by CI, is found to be defective in materials or
workmanship. As a condition to the obligation of CI to repair or replace such product, the product must be returned to CI together
with proof-of-purchase satisfactory to CI.
B. The Proper Return Authorization Number must be obtained from CI in advance of return. Call Celestron at [phone] to receive
the number to be displayed on the outside of your shipping container.
All returns must be accompanied by a written statement setting forth the name, address, and daytime telephone number of the owner,
together with a brief description of any claimed defects. Parts or product for which replacement is made shall become the property of
CI.
The customer shall be responsible for all costs of transportation and insurance, both to and from the factory of CI, and shall
be required to prepay such costs.
CI shall use reasonable efforts to repair or replace any product covered by this limited warranty within thirty days of receipt. In the
event repair or replacement shall require more than thirty days, CI shall notify the customer accordingly. CI reserves the right to
replace any product which has been discontinued from its product line with a new product of comparable value and function.
This warranty shall be void and of no force of effect in the event a covered product has been modified in design or function,
or subjected to abuse, misuse, mishandling or unauthorized repair. Further, product malfunction or deterioration due to
normal wear is not covered by this warranty.
CI DISCLAIMS ANY WARRANTIES, EXPRESS OR IMPLIED, WHETHER OF MERCHANTABILITY OF FITNESS FOR A
PARTICULAR USE, EXCEPT AS EXPRESSLY SET FORTH HEREIN.
THE SOLE OBLIGATION OF CI UNDER THIS LIMITED WARRANTY SHALL BE TO REPAIR OR REPLACE THE COVERED
PRODUCT, IN ACCORDANCE WITH THE TERMS SET FORTH HEREIN. CI EXPRESSLY DISCLAIMS ANY LOST
PROFITS, GENERAL, SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES WHICH MAY RESULT FROM BREACH OF
ANY WARRANTY, OR ARISING OUT OF THE USE OR INABILITY TO USE ANY CI PRODUCT. ANY WARRANTIES
WHICH ARE IMPLIED AND WHICH CANNOT BE DISCLAIMED SHALL BE LIMITED IN DURATION TO A TERM OF ONE
YEAR FROM THE DATE OF ORIGINAL RETAIL PURCHASE.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitation on how long an implied
warranty lasts, so the above limitations and exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
CI reserves the right to modify or discontinue, without prior notice to you, any model or style telescope.
If warranty problems arise, or if you need assistance in using your CI product, contact:
Celestron International
Customer Service Department
2835 Columbia Street
Torrance, CA 90503
Tel. [phone]
Fax. [phone]
Monday-Friday 8AM-4PM PST
This warranty supersedes all other product warranties.
NOTE: This warranty is valid to U.S.A. and Canadian customers who have purchased this product from an Authorized
CI Dealer in the U.S.A. or Canada. Warranty outside the U.S.A. and Canada is valid only to customers purchased from
a CI International Distributor or Authorized CI Dealer in the specific country and please contact them for any warranty
service.
Printed in China
1098