CELTIPOL C-M 16 User manual

TECHNICAL MANUAL
C-M 16
Faustino Santalices, 35
32840 Bande
Ourense (España)
E-mail:[e-mail]
Telf.:(34)988 443 105
Fax.:[phone]
www.celtipol.com
TRANSFER PUMP FOR
POLYURETANE AND POLYUREA

Safety in the use of the equipment:
• It is advisable for personnel with a history of respiratory complaints to avoid exposure to all
isocyanates.
• Chemical products must be handled safely in accordance with manufacturer's
recommendations. The manufacturer should provide information on the toxicity of the
products used as well as actions to take in the event of accident (wounds, irritation, etc.).
• Products such as polyisocianates, organic solvents and diamines should be stored in a place
exclusively for and adapted to such a purpose, with restricted access. Maximum
temperatures must be strictly adhered to, both in the application and in storage of chemical
products, at all times following the manufacturer's recommendations.
• Also, chemical products are to be stored at all times in suitable containers, following the
manufacturer’s recommendations.
• Containers must not be opened until immediately before being used in order to avoid
contamination by damp. Any leftover product after being applied should be put back into the
original container and be stored in a dry, ventilated place.
• During cleaning tasks of spilt components, it will be essential to use eye protection, gloves
and wearing breathing apparatus. Spilt isocyanate can be collected with any absorbent inert
product, such as sawdust. In any case, it is important to avoid skin contact. The absorbent
product is to be immediately collected and dumped into an open container through the
upper part.
• Throughout the entire operation explained above, the area must be correctly ventilated.
Safety personnel equipment:
Celtipol recommends the following personnel
safety equipment :
» Protective mask for airways.
» Goggles to protect the eyes.
» Headset to protect against noise.
» Gloves to protect hands.
» Protective clothing for the body.
REF.
DESCRIPCIÓN
QT.
2918
Product outlet hose
1
2919
Air inlet hose
1
5001
Cilinder head cover
1
5002
Upper spring
1
5003
Liner
1
5005
O-ring Øint 65x3
2
5007
Lower spring
1
5008
Cylinder head base
1
5009
Rod guide
1
5010
Seal
1
5011
Piston rod
1
5013
Rod cane joint
1
5014
Main pump union
1
5015
O-ring Øint 60x1,75
1
5016
Screw M8
3
5017
Nut M10
1
5019
Pin
1
5024
Nylon closure ring
1
5025
Packing housing
1
5027
Felt housing
1
5029
Felt stop ring
1
5030
Pin
1
5031
Sphere holder
1
5032
Sphere Ø20
1
5035
Lower piston
1
5041
O-ring Øint 36x2,5
1
5042
Sphere holder
1
5043
Sphere Ø22
1
5044
Lower sphere holder
1
5045
Upper piston
1
5046
Lower piston plate
1
5047
Upper piston plate
1
5048
Stem
1
5049
Piston nut
1
5050
Piston stay bolt
3
5055
Screw M4
3
5056
Upper stem
1
5057
Top stop ring
1
5058
Lower stop ring
1
5064
Fluid separator
1
5065
O-ring Øint 40x2
1
5066
Internal cane
1
5067
Lower stem
1
5068
Suction rod
1
5080
Piston ring
1
7019
Joint M 1/2” – M 1 1/16” SAE
1
Kit.5006 Gaskets and felts
REF.
DESCRIPTION
QT.
5028
Felts
3
5826
Packing base
1
5827
Central packing
1
5069
Packing guide
1
Kit.5071 Lower piston
REF.
DESCRIPTION
QT.
5034
Piston board
1
5036
Piston guide
1
Kit.5072 Internal gaskets
REF.
DESCRIPtion
QT.
5059
Gasket ring kit
2
5060
Guide kit
1
Kit.5074 Drum holder
REF.
DESCRIPTION
QT.
5061
Waterpr. pump support
1
5062
O-ring Øin. 53x3
1
5063
Drum connection
1
Kit.5075 Upper piston
REF.
DESCRIPCIÓN
QT.
5051
Piston O-ring Øin 50x6
1
5052
Bottom plate gasket
3
5053
Upper plate gasket
1
5054
O-ring Øin. 16x2
1
Kit.5076 O-rings
REF.
DESCRIPTION
QT.
5005
O-ring Øint 65x3
2
5015
O-ring Øint 60x1,75
1
5041
O-ring Øint 36x2,5
1
5065
O-ring Øint 40x2
1
Kit.5077 Pressure regulator
REF.
DESCRIPTION
QT.
1104
Connector 1/4’’NPT Male
1
7093
Pressure regulator 10bar
1
1201
Manometer Ø42
1
1202
Stopcock 1/4’’ 20bar
1

Kit 5006 mounting:
Kit 5071 mounting:
Kit 5072 mounting:
Kit 5075 mounting:
Technical characteristics of the equipment
Air pressure:........................................................................................................... 7kg/cm²
Air consumption:..................................................................................................200l/min.
Maximum product outlet pressure:.....................................................................20kg/cm²
Pressure ratio:............................................................................................................2,8 : 1
Outflow:................................................................................................................. 30l/min.
Start up:
Insert the pump through the mouth of the drum
Screw the clamp to the drum (5074) and tighten the seal (It is recommended to apply grease to
both threads and gasket).
Open the breather cap of the drum.
Connect the product outlet hose (2918) at both ends.
Connect the air inlet hose (2919) to the pump, through the pressure regulator kit 5077.
Connect the air hose (2919) to the air outlet *. The pump will start working when the stopcock
(1202) is opened.
Turn the regulator (7093) until the pressure gauge (1201) reaches a maximum of 7 bar.
* To increase the durability of the equipment it is recommended to treat the air using dryers and
lubricate it.
Kit
5006
Kit
5071
Kit
5072
Kit
5075
5028
5069
5827
5826
5034
5036
5052
5051
5054
5053
5059
5059
5060
5077
5077
2919
2918
7019
1202
7093
1201
1104
Kit 5077
5074
7019

5001
C-M 16 TRANSVASE PUMP
5002
5049
5047
5003
5005
5045
5048
5050
5046
5055
5011
5007
5005
5009
5008
5010
5014
5016
Kit
5006
5030
5013
5015
5019
5027
5025
5024
5056
5057
5058
5064
5066
5065
5044
5042
5043
5067
5031
5080
5068
5032
5017
5035
5041
5029
Kit
5074
Kit
5075
5077
Kit
5072
Kit
5071