Centre Point CP-R10R User manual

1
CP-R10R Product Code: 400098
INSTRUCTION MANUAL
CP-R10R
ROTARY LASER LEVEL

2
Laser Safety
• Use the tool only with the
specifically designated batteries.
• Store the tool out of reach of children and
other untrained persons. Laser tools are
dangerous in the hands of untrained users.
• Use only accessories that are
recommended for your model.
• Tool service must be performed only by
qualified repair personnel. Repairs, service
or maintenance performed by unqualified
personnel will void the warranty.
Only approved and authorised service
technicians can carry out warranty repairs.
• Do not use optical tools such as a telescope
or transit to view the laser beam. Serious
eye injury could result.
• Do not place the tool in a position which
may cause anyone to intentionally or
unintentionally stare into the laser beam.
Serious eye injury could result.
• Do not position the tool near a reflective
surface which may reflect the laser beam
toward anyone’s eyes. Serious eye injury
could result.
• Do not set up the tool at a position where
the laser beam can cross any person at
head height.
• Do not let children come in contact with
the tool.
• Turn the tool off when it is not in use.
Leaving the tool on increases the risk of
staring into the laser beam.
• Do not operate the tool around children or
allow children to operate the tool. Serious
eye injury may result.
• Position the tool securely on a level
surface. Damage to the laser or serious
injury could result if the laser falls.
• Do not remove or deface warning labels.
• Never look into the laser beam directly
and intentionally.
• Do not use optical tools to view the
laser beam.
• Do not set up the tool at a position
where the laser beam can cross any
person at head height.
• Do not let children come in contact
with the laser.
Read the following safety instructions before attempting to operate this tool.
Keep these instructions in a safe place or store in the carry pouch for future reference.
There are no user serviceable parts inside.
Disassembling the tool will void all
warranties on the product. Do not modify
the tool in any way. Modifying the tool may
result in hazardous laser radiation exposure.
CAUTION!
CLASS 2 LASER PRODUCT
WARNING! SAVE ALL WARNINGS & INSTRUCTIONS FOR FUTURE REFERENCE.
Read and understand all instructions.
!
!
WARNING!
DO NOT DISASSEMBLE THE LASER.

CP-R10R KIT
3
Please ensure the following items are included with your laser level.
If anything is missing please contact your retailer.
Item Checklist
Centre Point
CP-R10R
Laser glasses
(red)
9V Alkaline battery
(detector)
Centre Point CP-DR3
detector & clamp
Laser target
(red)
INCHES CM
1
1
2
3
4
5
6
7
2
3
AA Alkaline
batteries (x4) Hard carry case

OVERVIEW
CONTROL PANEL
4
Using the Laser
Battery compartment
Control panel
Laser port
Power
Power indicator
Tilt alarm
Tilt alarm indicator
I.R sensor
5/8” x 11 tripod thread
Protective lighthouse

5
Using the Laser (continued)
POWER SUPPLY
• The instrument is supplied with four AA 1.5V
alkaline batteries as its main power source.
Battery replacement
• Unscrew and remove the battery cover door
and the batteries
• Insert the alkaline batteries into the battery
tray according to polarity.
• Replace the battery cover door and tighten
the screw.
SETUP
• Select a place as close as practical
to the work site. Ensure the location
is clear of traffic.
• Place the laser on a level surface
such as a bench or supplied mount.
OPERATION
Powering on
• Press the power button once and
the instrument will power on and begin
automatically self-levelling. When this
levelling process is complete, the penta
prism inside the lighthouse will start rotating.
• If the instrument is outside the self levelling
range the instrument will not level causing the
laser beam to flash continuously. If this occurs,
reposition the instrument onto a level surface
until the instrument can level off.
Powering off
• Press the power button once and the
instrument will power off.
Tilt alarm
• Once the instrument has been levelled off the
tilt alarm can be enabled by pressing the tilt
alarm button. The tilt alarm indicator light will
flash continuously whilst active.
• If the instrument is disturbed while the alarm
is active the instrument will stop rotating and
will need to be powered off and on again to
reset its level position.

FRONT OVERVIEW
BACK OVERVIEW
6
Using the Detector
Bubble vial
Laser sensor
LCD display screen
Power button
Coarse / fine detection
Speaker
Battery compartment
Staff clamp thread
LCD display screen

FIGURE 1
7
Using the Detector (continued)
POWER SUPPLY
• The detector is supplied with one 9V alkaline
battery as its standard power source.
Removing & inserting the alkaline battery
• Open the battery cover door.
• Insert the alkaline battery into
the battery tray according to polarity.
• Close the battery cover door.
SET UP
Mounting the staff clamp
• Insert the staff clamp screw
into the staff clamp thread.
• Rotate the thumb screw until
the clamp is secured in place.
OPERATION
Powering on
• Switch the detector on by pressing the
power button. The speaker will emit a small
tone to indicate the instrument is operating.
• The LCD screen will display the battery level
detection mode and speaker function.
Speaker function
• Press the speaker button
to turn the speaker off / on.
Operation with a rotary laser level
• Turn on the rotary laser level.
• To change between coarse and fine detection
mode press the coarse / fine mode button/
• Move the detector into
the path of the laser beam.
• Hold the detector upright to
detect the horizontal beam (Fig.1)
• The direction arrows or level line on the LCD
screen will indicate the position of the laser
beam. The detector will emit a constant beep
once the level position has been located.

8
Care & Maintenance
1. This is a precision measuring tool and
should always be handled with care and
transported within the carry pouch provided.
2. Always turn the tool off when transporting
the laser level or moving around the job site.
3. Whenever possible, store the tool in a dry,
shady location.
4. When the tool is not in use or is being
stored, it is highly recommended to
remove the batteries.
5. Calibration of the tool is recommended every
six months, if ongoing accurate levelling is
required, or an impact has occurred.
6. The operator should check the accuracy
of the tool before precision levelling is
attempted. Failure to do so may result
in inaccurate measurements.
7. Clean the tool with a dry, soft cloth after use in
dusty, damp or wet conditions before storing.
8. Smudges and fingerprints may be removed
with a damp tissue or a soft, lint-free cloth.
Using the Tripod
A tripod can be purchased from your
nearest measurement tool dealer. The
below instructions are generic only and
set-up methods may vary between models.
Refer to the documentation from the
tripod manufacturer for details.
• Extend the tripod legs to the required height
and ensure the legs are spread wide enough
so that the tripod platform is stable. Secure the
legs in place (refer to the documentation from
the tripod manufacturer for details).
• Place the laser level onto the tripod and mount
via the male thread (5/8” into the base until
firm. Do not over tighten as this may cause
damage to the laser level or tripod.
NOTE: adjustment methods will vary on
tripod models. Always ensure that any locking
levers are unlocked before making adjustments
and returned to the locked position when the
adjustment is complete.
If using an elevating tripod with a measuring
scale on the centre column, the height can be
adjusted as required.
WARNING! Attaching the laser to
a tripod without the correct thread
size may cause damage.
!
NOT INCLUDED

9
If the above troubleshooting steps do not resolve any issue that you may have, please contact 24-hour support.
Trouble Shooting
Laser level does
not power on
• Check the batteries. They may be in the wrong way or need replacing.
• Check the battery compartment for signs of damage and
ensure that the compartment and battery terminals are clean.
Laser level turns on
but does not rotate
• Check the batteries. They may be in the wrong way or need replacing.
• Check the battery compartment for signs of damage and ensure
that the compartment and battery terminals are clean and not bent.
Laser level does
not remain on for
long periods of use
• Check the batteries. They may be in the wrong way or need replacing.
• Check the battery compartment for signs of damage and ensure
that the compartment and battery terminals are clean and not bent.
Laser level does
not level off
• The laser level may be outside of its self-levelling range and
may require an adjustment before self-levelling can commence.
• Check the batteries. They may have low power.
• The laser level may have impact damage and
may require repairs to become operational.
Detector does not
detect the laser beam
• Check that the laser level is powered on.
• Check the detector battery. The battery may require replacing.
• Check the laser is operating correctly.
Detector speaker
is not functioning
• Check sound is on.
• Check the laser is operating correctly and producing a beam.
ERROR / PROBLEM CAUSE / SOLUTION

10
Warranty
1. Our warranty provides the correction of
deficiencies to the tool once verified by an
authorised service centre that the deficiencies
were caused by a manufacturing fault within
the warranty period.
2. The warranty period is 3 years from the
date of purchase. The warranty period can
be extended to 7 years upon registration
of the tool within 30 days of purchase.
3. The warranty does not cover:
a) Calibrations and components
that are subject to wear and tear.
b) Defects in the tool caused by
non-compliance with the operation
instructions, improper use, abnormal
environmental conditions, inappropriate
operating conditions or insufficient
maintenance.
c) Defects caused by using accessories or
spare parts other than approved parts.
d) Services or repairs carried out
by non-authorised persons.
4. Defects recognised by an authorised service
centre as being covered by the warranty shall
be corrected either by repair or replacement
of the tool.
This tool comes with a standard 3 year warranty. Extend the warranty of your
laser level to 7 years by registering online. See website for terms and conditions.
All Spot-on measurement tools are carefully checked and tested to our precise quality assurance standards.
We offer a warranty in accordance with the following conditions:
www.spoton.com.au/warranty-information
5. The warranty claim must be lodged within the
warranty period. This requires the complete
tool with the original sales receipt containing
the purchase date and place of purchase.
Partial or disassembled tools cannot be
submitted for a warranty claim.
6. Services provided under warranty do not
lengthen or renew the warranty of the tool.
“Our goods come with guarantees that cannot
be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for
a major failure and for compensation for any
other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a
major failure.”
For more information please visit
consumerlaw.gov.au

11
To assist you with any queries or technical
questions please contact customer support.
1300 658 338
Visit www.spoton.com.au for more information.
Customer Support
Product code 400098
Warranty 7 Years (with online registration)
Accuracy ±1.5mm at 30m
Operating range 250m (diameter)
Levelling range ±9% / ±5°
Maximum rotation speed 600rpm
Laser class 2 Red
Battery life 20 hours
Battery type 4x 1.5V AA
Horizontal lines 1
IP rating 65
Weight (kg) 1.2
Dimensions (mm) 135 x 145 x 165
Specications
SPECIFICATIONS CP-R10R

Spot-on Laser & Tool Company Pty Ltd
Spot-on Laser & Tool Company Pty Ltd reserves the right to make changes to specications and
product descriptions atany time. © Spot-on Laser & Tool Company Pty Ltd. 2021. Printed in China.