Ceotis STAR ECO User manual

IP65
STAR ECO LED Floodlight Installation Guide
Size Color Temp Initial
Lumens PF
3000K
20W185*135*39mmCOP-ECO-20-FB 1530lm AC220-240V 50Hz 40
10W149*105*39mmCOP-ECO-10-FB 3000K 770lm AC220-240V 50Hz 40
3000K30W300*203*39mmCOP-ECO-30-FB 2450lm AC220-240V 50Hz 40
3000K50W300*203*39mmCOP-ECO-50-FB
COP-ECO-20-FB
COP-ECO-10-FB
COP-ECO-30-FB
COP-ECO-50-FB
COP-ECO-20-FB
COP-ECO-10-FB
COP-ECO-30-FB
COP-ECO-50-FB
4050lm AC220-240V 50Hz 40
>0.9
>0.9
>0.9
>0.9
Light-emitting
area
0.0085m2
0.0117m2
0.0380m2
0.0380m2
4000K
20W185*135*39mm 1700lm AC220-240V 50Hz 40
10W149*105*39mm 4000K 850lm AC220-240V 50Hz 40
4000K30W300*203*39mm 2700lm AC220-240V 50Hz 40
4000K50W300*203*39mm 4500lm AC220-240V 50Hz 40
>0.9
>0.9
>0.9
>0.9
5000K
20W185*135*39mm 1700lm AC220-240V 50Hz 40
10W149*105*39mm 5000K 850lm AC220-240V 50Hz 40
5000K30W300*203*39mm 2700lm AC220-240V 50Hz 40
5000K50W300*203*39mm 4500lm AC220-240V 50Hz 40
>0.9
>0.9
>0.9
>0.9
0.0085m2
0.0117m2
0.0380m2
0.0380m2
0.0085m2
0.0117m2
0.0380m2
0.0380m2
>0m
- THE PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN.
- THE POWER SUPPLY MUST BE TURNED OFF BEFORE INSTALLATION.
- NO WARRANTY WILL BE ACCEPTED IF THIS PRODUCT IS NOT INSTALLED BY A QUALIFIED
ELECTRICIAN.
- DO NOT OPERATE THE PRODUCT WITH A DAMAGED TEMPERED GLASS; THE DAMAGED
TEMPERED GLASS SHOULD BE REPLACED BY THE SERVICE AGENT.
- THE DRIVER CAN’T BE REPLACED.
- WHEN PRODUCTS ARE INSTALLED IN HIGH WIND ENVIRONMENTS, APPROPRIATE INSTALLATION/
FASTENING METHODS MUST BE APPLIED SO THAT THE PRODUCT MOUNTING POINTS ARE NOT
DAMAGED DUE TO VIBRATION,MOVEMENT OR CORROSION.
- GOOD PRACTICE DOES NOT RECOMMEND CONTINUOUS USE WITHOUT APPROPRIATE
SWITCHING CYCLES.
- THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT REPLACEABLE; WHEN THE LIGHT SOURCE REACHES
ITS END OF LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.
- THE EXTERNAL FLEXIBLE CABLE OR CORD OF THIS LUMINAIRE CANNOT BE REPLACED; IF THE CORD IS
DAMAGED, THE LUMINAIRE SHALL BE DESTROYED.
- IT IS RECOMMENDED TO USE A SUPPLY BOX WITH A MINIMUM IP65.THE REQUIREMENT OF CONNECT
LIGHTING USE 3P TERMINAL.
- THE TERMINAL IS RATED VOLTAGE IS 300V,RATED CURRENT IS 3A,THE WRING IS NOT LESS THAN
3x1.0MM .
- TERMINAL BLOCK IS NOT INCLUDED.INSTALLATION AND MAINTENANCE SHOULD BE IN ACCORDANCE
WITH RELEVANT LOCAL REGULATIONS (WHERE APPLICABLE) BY AN AUTHORISED AND LICENCED
ELECTRICIAN.
2
L*W*H
1.06KG
Net Weight
1.26KG
2.86KG
2.95KG
1.06KG
1.26KG
2.86KG
2.95KG
1.06KG
1.26KG
2.86KG
2.95KG

3
Installation of LED Floodlight
3. Loose the two fixing screws, then adjust the angle of support
bracket, and fix the screws at last.
1. Disconnect mains supply before installation or
removing cover.
2. Drill two holes in the installation location, then fix the product in the
location with screws. Distance between holes are in the chart.
A
B
C
COP-ECO-10-FB
Model: A(mm) B(mm) C(mm)
12.0 52 88
12.0 62 118
12.0 62 158
12.0 62 158
COP-ECO-20-FB
COP-ECO-30-FB
COP-ECO-50-FB
CEOTIS ECLAIRAGE
C/O SOITEC
Parc technologique des fontaines
Chemin des Franques
38190 Bernin France
Email:[email protected]
TEL: [phone]
5
5. Reconnect mains supply.
4
L(BROWN)
N(BLUE)
(GREEN/YELLOW)
INPUT
CABLE
3X1.0mm²
Outer insulation
Inner insulation
40±3mm
6±2mm
4.Individually connect the Live wire, Neutral wire and Ground wire of AC
input wire to Brown, Blue and Green-Yellow wire. All cable terminals must
be installed in accordance with the designed IP rating.