CET C.A. Technologies Panther P100H User manual

HVLP AIR CAP AND FLUID NOZZLE CHART
MODEL
NO. AIR CAPS Press / Siphon
*MAX GUN
INLET PRESS.
FOR HVLP
FAN
CONTROL
SCFM @
MAX GUN
INLET
AIR CAP
RING
AVAI LABLE FLUI D
NOZZLES TIPS
NEEDLES /
marking on needle
21-1090 pressure 15 6 31-0205 0.5mm (.020")
21-1091 pressure 15 8 31-0208 0.8mm (.022")
21-1092 pressure 15 8 31-0210 1.0mm (.040")
21-1093 pressure 18 10 31-0212 1.2mm (.046")
21-1094 pressure 33 13 31-0213 1.3mm (.052")
21-1095 pressure 50 22.5 31-0214 1.4mm (.055")
21-1095T pressure 50 22.5 31-0215 1.5mm (.059")
21-1097 pressure 50 22.5 31-0216 1.6mm (.063")
21-1195 pressure 50 22.5 31-0217 1.7mm (.070")
21-1197 pressure 50 22.5 31-0412 1.2Fmm (.046") 40-1112F (112F)
31-0414 1.4Fmm (.055") 40-1114F (114F)
31-0417 1.7Fmm (.070") 40-1117F (117F)
*Note: Air cap test gages are available to confirm HVLP compliance.
Actual fluid nozzle and air cap combinations are determined by application (see application chart page 4)
*Gun inlet pressures may vary as required by application
40-1100 (100)
P100H
included
21-1001
60-1502 (#2)
PP
PP
Pantant
antant
anther 1her 1
her 1her 1
her 100H00H
00H00H
00H
TEFLON COATED SPRAY GUN
PRODUCT INFORMATION
DISTRIBUTED BY COATING EQUIPMENT TECHNOLOGY, INC
PHONE: [phone]
WEB: www.cetinc.com

Operation and Maintenance Instructions for
PP
PP
P100H100H
100H100H
100H Spray Guns
Operation
1. Connect air supply hose at handle of gun.
2. Connect a pressurized fluid supply to the gun fluid inlet.
3. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control
fluid flow by proper selection of fluid orifice size and use the fluid control knob to “fine tune flow rate”.
4. Fan width can be adjusted using the fan control knob. Turning the knob clockwise narrows the fan.
Maintenance
IMPORTANT! Routine cleaning and maintenance is essential to insure proper gun operation.
Several states prohibit spraying solvent into the atmosphere and require the use of covered gun cleaner.
1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufactures
instructions.
2. If a gun cleaner is not being used:
Remove air cap and clean separately using clean solvent.
For pressure setups, connect a pressurized solvent supply to the fluid inlet, trigger the gun allowing solvent to flow
thru the gun until clean.
NOTE: Gun head disassembly is not recommended for normal cleaning and maintenance.
Gun head disassembly and reassembly instructions:
Have repair kit # 10-110 available before gun disassembly.
Gun head disassembly
To remove the nozzle carrier (5) and air cap adapter (6):
1. Remove the air cap (1-2), fluid nozzle tip (3), fluid nozzle body (4), and needle (13).
2. Remove the needle seal cartridge (23).
3. Loosen the locknut (9) and remove fluid inlet (10) using a 5/8” open-end wrench.
4. The nozzle carrier (5) and air cap adapter (6) will now slide forward from the gun body (11).
Gun head reassembly
1. Install a new o-ring (7) on the air cap adapter (6).
2. Install the thread locknut (9) onto the fluid inlet (10) as far as possible.
3. Install a new fluid inlet seal (8) into the recess area on the nozzle carrier (5) inlet port.
4. Slide the nozzle carrier (5) into air cap adapter (6) and insert into the gun body (11) as far as possible. Be sure the
nozzle carrier (5) extends into the hole at the back of the gun head. Install the needle seal (23) but do not tighten.
5. Rotate the nozzle carrier (5) until the fluid inlet port in the nozzle carrier (5) is aligned with the threaded hole in the
body. While in this position, insert the fluid inlet (10) and tighten firmly.
6. Tighten the needle seal (23) to approx. 12 ft.-lb. torque.
7. Tighten the fluid inlet (10) to approx. 25 ft.-lb. torque.
8. Tighten the locknut (9) to approx. 33 ft.-lb. torque.

*
*
*
*
*
*
**
HVLP AIR CAP TEST GAGES
21-1090-G
21-1092-G
21-1093-G
FOR
P100H
GUNS
21-1095-G
21-1097-G
21-1195-G
21-1197-G
ITEM NO. PART NO. DESCRIPT ION ITEM NO. PART NO. DESCRIPT ION
1 See Air Cap Chart Air Cap Retaining Ring** 16 60-206 Needle Return Spring (HD)*
2 See Air Cap Chart Air Cap** 17 60-201 Rear Bushing
3 See Air Cap Chart Fluid Nozzle Tip** 18 60-119 Seal*
4 31-1201 Fluid Nozzle Body 19 60-1520 Air Valve Assembly
5 60-L11H Nozzle Carrier 20 60-302 Air Valve Poppet
6 60-12H Air Cap Adapter 21 60-125 O-Ring*
7 60-131 O-Ring* 22 61-1003 Air Valve Spring*
8 60-124 Fluid Inlet Seal 23 60-1400 Needle Seal Cartridge*
9 60-128 Locknut 24 60-2101 Trigger
10 60-126 Fluid Inlet Fitting 25 60-1510 Air Control
11 60-1116 Panther Gun Body HVLP 25A 60-122 Plug (optional)
12 See Air Cap Chart Fan Control Assembly** 26 60-104 Air Inlet Fitting
13 See Air Cap Chart Fluid Needle** 27 60-1033 Trigger Pivot Set
14 60-202 Fluid Control Knob 28 98-0109 Allen Plug
15 60-209 Spring Seat*
**See air cap selection chart on page 1
*Indicates part included in repair kit # 10-110

P100H HVLP SPRAY GUN
MATERIAL TYPE FLUID ORIFICE x
AI R C AP
MAXIMUM
PATTERN WIDTH PRESS. / SIPHON
Very Thin
less than 16 sec. Zahn #2
inks , dyes,
solvents, stains
Thin
16 to 20 sec. Zahn #2
lacquers, enamels,
primers, sealers
Medium
21 to 30 sec. Zahn #2
automotive base coat
enamels, primers
epoxies, urethanes
automotive clear coat
Heavy
over 30 sec. Zahn #2
heavy body primers
high solid enamels
high solid automotive coatings
adhesives
1.6, 1.7 mm x 1095
1.6, 1.7 mm x 1097
1.6, 1.7 mm x 1195
1.6, 1.7 mm x 1197
12
13
13
14
P
P
P
P
FLUID NOZZLE / AIR CAP SELECTION CHARTS
PANTHER Series 100H - Pressure Feed Guns
0.5, 0.8 mm x 1090
0.5, 0.8 mm x 1092
10
11
P
P
1.0, 1.2 mm x 1092
1.0, 1.2 mm x 1093
11
12
P
P
1.3, 1.4, 1.5 mm x 1093
1.3, 1.4, 1.5 mm x 1095
1.3, 1.4, 1.5 mm x 1097
12
12
13
P
P
P
Revised 3/18/14