CET CA Tech CPR-T3 User manual

CA Tech CPR-T3 Spray Gun
Click-n-Pick Spare Parts Cutsheet
Easily find spare parts without digging through the full manual.
Click on part numbers to order.

Orifice Size Air Cap
Max Gun Inlet
Pressure for HVLP /
Compliant
Orifice (Tip) Needle
1.3 23-1301*/ 23-2101 29 33-0213 40-P1313
1.4 23-1301* / 23-2101 29 33-0214 40-P1314
1.5 23-1301* / 23-2101 29 33-0215 40-P1315
1.7 23-1301* / 23-2101 29 33-0217 40-P1317
1.9 23-1301* 29 33-0219 40-P1319
2.2 23-1301* 29 33-0222 40-P1322
NOZZLE NEEDLE CHART
Part Number Description Part Number Description
1 60-1130 Body Assembly 6 See Below Needle
233-1202 Nozzle Body 7 T21 Needle Return Spring
3 See Below Orifice 8 T25 Fluid Control Knob
4 See Below Air Cap
5 T27 Packing 910-111 Tool Kit: Gun wrench, filter, needle
packing wrench and brush
CPR-T3
Part Sheet
1
2
9
45
7 86
10
*Note:
Do not remove fluid nozzle carrier from gun (#10)
The needle packing nut needs manual ad ustment and must be tightened periodically to avoid leaks. Use the packing wrench
supplied in 10-111 kit.
*Air Cap test gauges are available to confirm HVLP compliance.

Material Orifice Size CPR-T3 HVLP 23-1301 CPR-T3 Compliant 23-2101
Filler 1.7 29 PSI @ 13 CFM 29 PSI @ 11 CFM
Primer, Washprimer, Epoxy 1.4 - 1.7 29 PSI @ 13 CFM 29 PSI @ 11 CFM
Sealer 1.4 - 1.7 29 PSI @ 13 CFM 29 PSI @ 11 CFM
Single Stage 1.3 - 1.4 29 PSI @ 13 CFM 29 PSI @ 11 CFM
Basecoat 1.3 - 1.4 29 PSI @ 13 CFM 29 PSI @ 11 CFM
Clearcoat 1.3 - 1.4 29 PSI @ 13 CFM 29 PSI @ 11 CFM
High Solids Clears 1.4 - 1.5 29 PSI @ 13 CFM 29 PSI @ 11 CFM
CPR Techline Nozzle Selection Chart
Operation and Maintenance Instructions for CPR Techline Spray Guns
Operation
1. Connect air supply hose at handle of gun (see page 1 for suggested gun inlet pressures).
2. The optional air control valve built into the gun handle can be used to ad ust gun inlet pressure.
3. Screw the paint cup onto the guns gravity feed fluid inlet.
4. Fluid flow can be controlled using the fluid control knob, this restricts flow by limiting needle travel. It is best to control
the fluid flow by proper selection of fluid orifice size and use the fluid control knob to fine tune flow rate.
5. Fan width can be ad usted using the fan control knob. Turning the knob clockwise narrows the fan pattern.
Maintenance
IMPORTANT! Routine cleaning and maintenance is essential to insure proper gun operation. Several states prohibit
spraying solvent into the atmosphere and require the use of a covered gun cleaner.
1. If a gun cleaner is being used, connect and clean the gun in the gun cleaner according to the manufacturers
recommendations.
2. If a gun cleaner is not being used:
First clean the gravity feed cup thoroughly, then spray clean solvent through the gun until clean.
Revised 12/10/12
DISTRIBUTED BY COATING EQUIPMENT TECHNOLOGY, INC
PHONE: [phone]
WEB: www.cetinc.com