CG Emotron FDU 2.0 User manual

External control panel
Emotron FDU/VFX 2.0
Instruction manual
English

CG Drives & Automation 01-5928-01r1 1
External Control Panel for Emotron FDU 2.0 and VFX 2.0
Fig. 1 Blank control panel kit Fig. 2 Control panel kit
Above listed kits contains:
Control panel or blank panel, mounting frame, gland plate
with D-sub connector and ribbon cable, mounting clamps,
mounting screws, spacers, clips, washers and RS232 cable.
Length of the RS232 cable = 3m.
Table 1
Part number Discription Note
01-3957-21 Blank control panel kit, complete for size B
Select a blank control panel kit if your
AC-drive already is equipped with control
panel
01-3957-31 Blank control panel kit, complete for size C
01-3957-01 Blank control panel kit, complete for size D and up
01-3957-71 Blank control panel kit with coated board, complete for size B
01-3957-81 Blank control panel kit with coated board, complete for size C
01-3957-51 Blank control panel kit with coated board, complete for size D and up
01-3957-20 Control panel kit, complete for size B
Select a control panel kit if your AC-drive is
equipped with a blank panel.
01-3957-30 Control panel kit, complete for size C
01-3957-00 Control panel kit, complete for size D and up
01-3957-70 Control panel kit with coated board, complete for size B
01-3957-80 Control panel kit with coated board, complete for size C
01-3957-50 Control panel kit with coated board, complete for size D and up

2CG Drives & Automation 01-5928-01r1
Mounting the control panel in a cabinet door or external panel
Fig. 3 External control panel
In stand-alone units the control panel is mounted in the
front door of the AC drive. If the AC drive is mounted in a
cabinet, it may be appropriate to place the control panel in
the cabinet door.
Detail 2
Detail 1
Detail 3
Flatcable
Mounting frame
Control panel
in cabinet door
Gland plate
NOTE: A control panel with display can not be used on
the AC drive and the cabinet door at the same time, one
of the panels must be blank.

CG Drives & Automation 01-5928-01r1 3
Mounting instructions
1. Punch/drill hole in the cabinet door according to the
template on the last page.
2. Place the mounting frame into the hole from the outside
of the cabinet door.
3. Fasten the mounting frame in the cabinet door from the
inside using the three mounting clamps and screws
according to the Fig. 4.
Fig. 4 Mounting the mounting frame using the mounting
clamps.
4. Remove the gland plate at the bottom of the AC drive.
See Fig. 3, detail 3.
5. Mount the gland plate with D-sub contact according to
Fig. 3, detail 3.
6. Fasten the gland plate with two Allen screws and
washers.
7. Place the ribbon cable along the side of the AC drive.
Put the ribbon cable clips along the inner side of the
inverter, see Fig. 5, Fig. 6, Fig. 7 or Fig. 8.
Fig. 5 How to mount the ribbon cable and secure it with the
clips on size B
Fig. 6 How to mount the ribbon cable and secure it with the
clips on size C
Mounting clamps
Clips
Clips

4CG Drives & Automation 01-5928-01r1
Fig. 7 How to mount the ribbon cable and secure it with the
clips on size D.
Fig. 8 How to mount the ribbon cable and secure it with the
clips on size E and F
8. Mount the spacers and washers on the female D-sub
contact on the back of the control panel in the AC drive
door. See Fig. 3, detail 2.
9. Connect the ribbon cable, male connector, according to
Fig. 3, detail 2. and fasten it with 2 screws.
10. Connect the standard RS232 cable, female connector,
between the gland plate in the bottom of the AC drive
and the back plane of the control panel in the cabinet
door according to Fig. 3, detail 1.
11. Snap a blank panel into the frame on the AC drive.
12. Snap the control panel into the mounting frame in the
cabinet door.
Clips
Clips

CG Drives & Automation 01-5928-01r1 5
NOTE: When this printout is made from an electronic file,
make sure that it is scaled correctly according to the
mentioned dimensions.
92 mm
180,30 mm
