Chad Valley Baby Rainbow Lights & Sound User manual

Assembly Instructions - IMPORTANT! Keep for future reference
464/5667
Dimensions
Width - 72cm
Depth - 62cm
Height - 52.5cm
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400 800
BABY BY CHAD VALLEY RAINBOW LIGHTS AND SOU

WARNING
IMPORTANT! – KEEP FOR FUTURE REFERENCE
Safety and Care Advice
MAINTENANCE
Read the instructions carefully before use and keep them for future reference. The child may be
hurt if you do not follow these instructions.This product should be assembled by an adult.
WARNING---Never leave the child unattended.
WARNING---The child will be able to reach further and move rapidly when in the baby walking
Read the instructions carefully before use and keep them for future reference. The child
may be hurt if you do not follow these instructions.
1) Prevent access to stairs, steps and uneven surfaces;
2) Guard all fires, heating and cooking appliances;
3) Remove hot liquids, electrical flexes and other potential hazards from reach;
4) Prevent collisions with glass in doors, windows and furniture;
5) Do not use the baby walking frame if any components are broken or missing;
6) This baby walking frame should be used only for short periods of time(e.g.20min);
7) This baby walking frame is intended to be used by children who can sit unaided,
approximately from 6 months. It is not intended for children weighing more than 12kg;
8) Do not use replacement parts other than those approved by the manufacturer or distributor;
9) Follow instructions for routine maintenance and cleaning or washing.
Please check and maintain your walker regularly to prevent injury.
Inspect the parts regularly if some parts are broken.
Wash the plastic parts with warm soapy water.
Battery
-The recommended battery sizes for this unit is 1.5V size AA.
-Do not mix new & used batteries.
-Do not mix batteries of different types.
-Only the recommended batteries or equivalent are to be used, volts and size.
-Batteries should be inserted with the correct polarity.
-Remove batteries when unit is stored for a long period of time or when the batteries are exhausted
-Dispose exhausted battery properly
-Do not short-circuit supply terminals.
-Do not attempt to recharge a non-rechargeable battery.
-Rechargeable batteries are to be removed from the toy before being charged.
-Rechargeable batteries are only to be charged under adult supervision.
WASTE ELECTRICAL PRODUCTS SHOULD NOT BE
DISPOSED OF WITH HOUSEHOLD WASTE. PLEASE
RECYCLE WHERE FACILITIES EXIST. CHECK WITH
YOUR LOCAL AUTHORITY FOR RECYCLING ADVICE.

1.Parts List
Please check you have all the parts listed below
If you have damaged or missing components,
call the Customer Helpline:
03456 400 800
Phillips Screwdriver
T
Tools required（not included）
Toy
Frame
Seat
Tray
Cover
Universal Wheel
Bottom Base
Stopper
Directional
Wheel

2.Assembly
Step1
Ste 2
Step3a
p
1. Pull the upper tray to
the right position, make
sure the adjusting
mechanism is locked.
Never put your hands
between the bottom
base and the upper tray
to avoid clamping.
directional
wheel
universal
wheel
Insert the directional
wheels and universal
wheels into their
corresponding holes.
Locate the fabric seat.
Insert the fabric seat
into the opening as
shown. Locate the
four plastic tabs
attached to
the perimeter of the
seat. Insert each of
the eight plastic tabs
through the slots
located around the
perimeter of the seat
assembly. Pull the
tab completely
through the slot and
fasten into place.
a

Step3b
S
Step5
tep4
To unfold the walker,
please pull the tray
upward. WARNING:
Make sure the adjusting
mechanism is locked.
To fold the walker, turn
the adjusting button to
90 degree and press the
button upward to release
the lock, then push the
tray downward to the
folding position and
release the button.
Insert the fixation point of
toy tray to the plate hole
and press downward to
get a complete fixation.
Insert the front 3 buttons
to the corresponding
holes and pull down to
fix it firm.
3b
adjusting button
adjusting
mechanism

Step6
S
Step8
tep7
adjusting button
adjusting
mechanism
The toy features
buttons, music,
sounds, and lights for
child's enjoyment.
8
Your walker has 3
heightpositions. To
adjust the tray tothe
desired height, simply
pull the tray up.
WARNING: Ensure
locking device is
engaged.
To lower the tray,
turn the adjusting button
to 90 degree and press
the button upwards to
release the lock, then
adjust the tray to desired
position.
6
Open the battery cover,
and put in 3pcs “AA”
battery（not included)
(Pay attention the
electrode battery),and
close the cover with
fastening screw.
Fix the toy on the upper
tray of walker.
7

Argos
Avebury, 489-499 Avebury Boulevard, Milton Keynes, MK9 2NW
www.argos.co.uk
Customer Helpline: 03456 400 800