CHAINTECH 6AJA4T User manual

Declaration of Conformity
According to 47 CFR, Parts 2 and 15 of the FCC Rules
The following designated product:
is a Class B digital device that complies with 47 CFR Parts 2 and 15 of the FCC
Rules. peration is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference
that may cause undesired operation.
This declaration is given to the manufacturer:
CHAINTECH-EXCEL COMPUTER INC.
4427 Enterprise St. Fremont CA 94538 U.S.A.
http://www.chaintech-excel.com
Chaintech President: Simon Ho
Signature:
EQUIPMENT : MAINBOARD
MODEL NO. : 6AJA4T

Federal Communications Commission Statement
This device complies with FCC Rules Part 15. Operation is subject to the following two
conditions
!This device may not cause harmful interference
!This device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy. If this equipment is not installed
and used in accordance with the manufacturer's instructions, it may cause harmful
interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
following measures
!Reorient or relocate the receiving antenna.
!Increase the separation between the equipment and receiver.
!Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
!Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is required
to assure compliance with FCC regulations. Changes or modifications to this unit not
expressly approved by the party responsible for compliance could void the user's authority
to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for audio noise emissions from
digital apparatusses set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Manufacturer's Disclaimer Statement
The information in this document is subject to change without notice and does not represent a
commitment on the part of the vendor. No warranty or representation, either expressed or implied,
imade with respect to the quality, accuracy or fitness for any particular purpose of this document.
The manufacturer reserves the right to make changes to the content of this document and/or the
products associated with it at any time without obligation to notify any person or organization of
such changes. In no event will the manufacturer be liable for direct, indirect, special, incidental
or consequential damages arising out of the use or inability to use this product or documentation,
even if advised of the possibility of such damages. This document contains materials protected
by copyright. All rights are reserved. No part of this manual may be reproduced or transmitted
in any form, by any means or for any purpose without expressed written consent of it's authors.
Product names appearing in this document are mentioned for identification purposes only. All
trademarks, product names or brand names appearing in this document are registered property
of their respective owners.
Printed in Taiwan September 2001September 2001
September 2001September 2001
September 2001
POST-CONSUMER
RECYCLED PAPER

Table of Contents
Chapter 1 Introduction ........................................................................ 1
1-1 Product Specifications ..........................................................1
1-2 Package Contents .................................................................2
1-3 Mainboard Layout ..................................................................3
1-4 Connector and Jumper eference Chart ..............................4
Chapter 2 Hardware Setup ................................................................... 5
2-1 Installing a CPU in a Socket 370 ..........................................5
2-2 Setting Your CPU's Parameter........................................ 5
2-3 Connector and Jumper Settings...........................................6
2-4 Main Memory Configuration ................................................10
Chapter 3 Award BIOS Setup Program ...........................................11
3-1 Standard CMOS Setup........................................................12
3-2 Advanced BIOS Features Setup ........................................14
3-3 Advanced Chipset Setup ....................................................17
3-4 Integrated Peripherals .........................................................20
3-5 Power Management Setup ..................................................21
3-6 PnP/PCI Configuration ........................................................24
3-7 PC Health Status.................................................................25
3-8 Frequency/Voltage Control..................................................25
3-9 Load Fail-Safe Defaults .......................................................26
3-10 Load Optimized Defaults .....................................................26
3-11 Supervisor Password & User Password Setting ................27
3-12 Save and Exit Setup ...........................................................27
3-13 Exit Without Saving ............................................................. 27
Feature ExplanationsFeature Explanations
Feature ExplanationsFeature Explanations
Feature Explanations
Software Power-off Control .............................................................6
Blinking LED in Suspend Mode ......................................................6
Poly-fuse Over Current Protection .................................................6
Over-ride Power Button...................................................................7
Power On By Modem .......................................................6/23
TC Alarm esume.......................................................23
Wake Up On LAN ...................................................................... 9/23
Appendices
Appendix I Embedded Flash Utility ..............................................28
Appendix II HDD Instant ecovery Utility ....................................29
Appendix III CMedia 8738 Audio Subsystem ..............................31

1
Introduction
+D=FJAH 
Introduction
1-1 Product Specifications
!!
!!
! Processor
- Supports Intel Socket 370 processors
- System clock 66/100/133MHz
This mainboar oes not support PPGA Celeron processor
!!
!!
! Chipset
- VIA VT82C694T + VT82C686B ual chip AGPset
!!
!!
! DRAM Memory
- Three 168-pin DIMM sockets support up to 1.5GB for SDRAM
- Supports PC100/PC-133 SDRAM
!!
!!
! Expansion Slots
- One Universal-AGP slot for both 2X/4XAGP (v2.0 compliant)
- Five 32-bit PCI slots (Rev 2.2 compliant)
- One ISA slot share with PCI slot
!!
!!
! Boot-Block Flash ROM
- Award B OS, supports PnP, APM, DMI, ACPI & Multi- evice booting
features i.e. floppy, LS120, CD-ROM, HDD(IDE, SCSI), ZIP-ATAPIetc.
- Inclu es Trend ChipAway Virus protection for virus-free boot an virus-free
operating system.
!!
!!
! Embedded Ultra DMA-66/100 PC DE controller
- Supports two IDE ports up to 4 ATAPI evices
- Supports up to PIO Mo e 4 up to 16.6MBps, Multi Mo e 4 up to 66MBps
an Multi Wor Mo e 5 up to 100MBps with bus mastering
!!
!!
! Onboard Ultra /O
- Two UARTs support serial port an IR function
- One parallel supports SPP/ECP/EPP
- One floppy isk rive connector supports up to 2.88MB
!!
!!
! Double Stack Back-Panel /O Connectors
- PS/2 Mini-DIN keyboar an mouse port
- Two USB ports
- Two 9-pin D-SUB male Serial port
- One 25-pin D-SUB female Printer port
- Au io Line-in/out an Mic-in jacks
- One 15-pin D-SUB female Game/MIDI port

2
Chapter 1
!!
!!
!
""
""
" Optional Audio Subsystem AC-link
- Full- uplex operation for simultaneous recor ing an plackback
- Built-in FM-emulation music synthesizer
- External high quality AC97 CODEC provi es 90 B+SNR CD quality au io
!!
!!
!Optional External PC Audio Subsystem
- CMe ia 8738 au io chip w/ legacy au io SB16/Pro compatible
- A vance 64-Voice Wavetable synthesizer
- 6-Channel speaker audio support
- Full- uplex operation for simultaneous recor ing an playback
!!
!!
! Embedded System Monitor Hardware
- 5 external voltage inputs (internal etecting)
- 2 temperature sensor with thermistor for CPU
- 2 Fan spee (CPU an System) monitoring with CPU Fan ON/OFF control in
suspen
!!
!!
! EmbeddedUSB Controller
- UHCI compliant USB host controller with Root Hub
- Four USB ports (UHCI v1.0 compliant)
- Optional USB riser with a itional 2 USB ports
1-2 Package Contents
This pro uct comes with the following components:
!One mainboar
!One 40-pin (80-wire) UDMA-66/100 IDE connector ribbon cable (Figure 1-1)
* Color coded connection for UDMA-66/100 cable
Blue to mainboar , Gray to Master an Black to slave
!One 34-pin floppy isk rive ribbon cable (Figure 1-2)
!One User's Manual
!One CD-ROM that inclu es
- Awar Flash Utility
- Awar DMI Utility for DOS
- Au io river an utility for Win9x/ME, NT an Win2000
- VIA Service Pack for Win9x/ME/2000/WinNT inclu ing Bus Master IDE
rivers, AGP VxD an etc.
- Optional Value Pack 2001 software group inclu ing Norton AntiVirus, AutoSave,
ADOBE ActiveShare, Acrobat Rea er, Imagemore, X-stop, Appio an Ewalla.
See the Readme.txt file in the CD-ROM's root directory for installation
instructions of all driver and soft are utilities.
#
Figure 1-2 Standard Floppy cableFigure 1-1 IDE UDMA-66/100 cable
#

3
Introduction
1-3 Mainboard Layout
PS/2 Keyboard USB 1/2 COM1 Line-out Line-in
COM2
JP6A,JP8,CN4B,CN20,IR1
CN2,CN3,CN4
CN22,FAN1 JP6
JP2A/2B,JP4,FAN3
CN1A,CN5,CN17
FAN2,JP1
PS/2 Mouse Printer Port Game Port
Mic

4
Chapter 1
1-4 Connector and Jumper Reference C art
Jumper &
Connector No. Function Page
PW1 ATX Power Supply Connector 6
JP1 Clear CMOS Data 8
JP2A/JP2B E ternal Clock Frequency 8
JP4 CPU Frequency Ratio 8
JP6/JP6A Power On By USB 8
JP8 Optional Onboard CMEDIA Audio 8
CN1A
Over Ride Power Button Connector
7
Power Indicator LED Connector
Green Switch/GreenLED Connector
System Reset Switch Connector
Speaker Connector
IDE Activity LED Connector
CN2 CD-ROM Audio in Connector 9
CN3 Au illiary Audio-in Connector 9
CN4 Audio Mono-in/out Connector(CODEC) 9
CN4B Optional Bass/Center Speaker Connector 9
CN5 WOL (Wake-on-LAN) Connector 9
CN17 Blue LED Connector 9
USB1/CN20 USB 1/2 Ports and USB 3/4 Connectors 9
CN22 Front Panel Audio Connector 9
IR1 IR Connector 10
FAN1/FAN2/FAN3 CPU/System Cooling Fan Connectors 10
PT1 PS/2 Mouse and Keyboard Ports 10

Hardware Setup
5
+D=FJAH
0=H@M=HA5AJKF
If your mainboard has already been installed in your computer you may still need
to refer to this chapter if you plan to upgrade your system's hardware.
2-1 Installing a CPU in a Socket 370
The Intel Socket 370, designed for the eleron/ oppermine processor, has been
incorporated as a standard mainboard specification To insert your PU into Socket
370 please do the following:
1. Locate a small dot marked on the top surface of the PU close to one if it's corners.
The same corner will also be cut off, leaving a noticeable notch in the PU's corner.
These markings indicate Pin 1 of the PU.
2. Pull up the lever of Socket 370 so that it is perpendicular with the surface of the
mainboard. Gently insert the PU with Pin 1 at the same corner of Socket 370
that contains the end of the lever. Allow the weight of the PU to push itself
into place. Do not apply extra pressure as doing so may result in damaging your
PU. Snap the lever back into place.
Installing a heat sink with cooling fan is necessary for proper heat dissipation
from your CPU. Failing to install these items may result in overheating and
possible burn-out of your CPU.
The use of a eatsink and Fan designed for the FC-PGA on a FC-PGA2 can cause
damage to the socket or motherboard and will void any warranty. The extra
thickness created by the I S will cause the eatsink and fan retention clip to
exert extra stress on the Socket, Processor or Motherboard.
2-2 Setting Your CPU's Parameter
Frequency Configuration
If you install a PU on this mainboard, you must set PU Frequency Ratio(JP2) and
JP3/JP4 for External lock Frequency.
* CPU Speed = Frequency ratio x External clock (System) Frequency
You do not need to make voltage settings because SeePU automatically sets
your CPU voltage.

Chapter 2
6
2-3 Connector and Jumper Settings
onnectors are used to link the system board with other parts of the system, including
the power supply, the keyboard, and the various controllers on the front panel of
the system case.
The power supply connector is the last connection to be made while installing a
mainboard. Before connecting the power supply, please make sure it is not
connected to the power source.
ATX Power Supply Connector (PW1
The power cord leading from the system's power supply to the
external power source must be the very last part connected when
assembling a system.
The ATX power supply provides a single 20-pin connector
interface which incorporates standard +/-5V, +/-12V, optional 3.3V
and Soft-power signals. The Soft-power signal, a 5V trickle supply
is continuously supplied when A power is available. When the
system is in the Soft-Off mode, this trickle supply maintains the
system in it's minimum power state.
Software Power-Off Control
This mainboard can be powered down using theWindows 95 Software Power-Off
function. To power down your computer, click the START button on the Windows 95
task bar. Select "Shut Down The omputer" and the system turns off. The message "It
is now safe to turn off your computer" will not be shown when using this function.
Power-On By Modem
While in Soft-off state, if an external modem ring-up signal occurs, the system wakes up
and can be remotely accessed. You may enable this function in BIOS's Power
Management Setup menu. (See section 3-5)
Blinking LED in Suspend Mode
While in Suspend mode, the LED light on the front panel of your computer will flash.
Suspend mode is entered by pressing the Override Power Button, pushing the Green
button on your ATX case, or enabling the Power Management and Suspend Mode
options in BIOS's Power Management menu. (See section 3-5)
Poly-fuse Over Current Protection
The poly-fuse protects the system from dangerous voltages the system might be
exposed to via the keyboard or USB connectors. In case of such exposure, the poly-
fuse will immediately be disconnected from the circuit, just like a normal fuse. After
being disconnected for a certain period of time, the poly-fuse will return to its normal
state, after which the keyboard or USB can function properly again. Unlike
conventional fuses, the poly-fuse does not have to be replaced, relieving the user
wasted time and inconvenience.

Hardware Setup
7
Front Panel Connector Set (CN1A A through F
A. Over-ride Power Button Connector
The power button on the ATX chassis can be used as a
normal power switch as well as a device to activate
Advanced Power Management Suspend mode. This mode
is used for saving electricity when the computer is not in use
for long periods of time. The Soft-OFF by PWR-BTN
function in BIOS's Power Management Setup menu must be
set to "Delay 4 Sec." to activate this function.
When the Soft-OFF by PWR-BTN function is enabled,
pushing the power button rapidly will switch the system to
Suspend mode. Any occurence of external activities such
as pressing a key on the keyboard or moving the mouse will
bring the system back to Full-On. Pushing the button while
in Full-On mode for more than 4 seconds will switch the
system completely off. See Over-ride Power Button
Operation diagram.
B. Power Indicator LED Connector
The power indicator LED shows the system's power status. It is important to
pay attention to the correct cables and pin orientation (i.e., not to reverse the order
of these two connectors.)
C. Green Switch Green LED Connector
Some ATX cases provide a Green switch which is used to put the system in
Suspend mode. In Suspend mode, the power supply to the system is reduced
to a trickle, the PU clock is stopped, and the PU core is in it's minimum power
state. The system is woken up whenever the keyboard or mouse is touched. The
system resumes in different ways as defined by Power Management Setup screen
in BIOS.
D. System Reset Switch Connector
This connector should be connected to the reset switch on the front panel of
the system case. The reset switch allows you to restart the system without turning
the power off.
E. Speaker Connector
This 4-pin connector connects to the case-mounted speaker
F. IDE Activity LED Connector
The IDE activity LED lights up whenever the system reads/writes to the IDE
devices.
Over-ride Power Button

Chapter 2
8
Clear CMOS Data (JP1
To clear the contents of the MOS, please follow the steps
below.
1. Disconnect the system power supply from the power source.
2. Set the jumper cap at location 2~3 for 5 seconds, then set it back
to the default position.
3. onnect the system's power and then start the system.
4. Enter BIOS's MOS Setup Utility and choose Load Setup
Defaults. Type Y and press enter.
5. Set the system configuration in the Standard MOS Setup
menu.
External Clock Frequency (JP2A/JP2B
This jumper allows the system bus frequency to be determined
either by PU or the user. If set both JP2A/JP2B pins to 1-2, the
PU determines the system bus frequency speed. Set both JP2A/
JP2B pins to 2-3 for 66MHz FSB, set only JP2B pins to 2-3 for
100MHz FSB and leave both JP2A/JP2B pins open for 133MHz
FSB.
CPU Frequency Ratio (JP4
This feature allows you to set a PU at a
higher frequency clock ratio than it's speci-
fication allows. it may or may not run at that
ratio, depending on the quality of your PU
and the extent to which the ratio has been
overset.
Power On By USB 1/2 and 3/4 (JP6/JP6A
This board is able to be turned on by a USB keyboard hot key
or a USB mouse click. To use this function, select a hot key
of your choice at the USB Resume From S3 option under Wake
Up Events in the BIOS's Power On Management screen. You
must also set both jumper's cap to pins 2-3 to use this function.
Optional C-Media Onboard Audio (JP8
This function allows you to enable and disable the on board
audio. You must set the jumper's cap to pins 1-2 to enable or
set pins 2-3 to disable this function.
FSB JP2A JP2B
Auto 1~2 1~2
66 2~3 2~3
100MHz Open 2~3
133MHz Open Open




Pin Definition
1~2 Normal (default)
2~3 Clear CMOS Data
This option will not work with
frequency lock PU.




Pin Definition
1~2 Disable (default)
2~3 Enable




Pin Definition
1~2 Enable
2~3 Disable
RATIO 5.5 6 6.5 7 7.5 8 8.5 9 9.5 10 10.5 11 11.5 12
A Off On Off Off Off On Off Off On On On Off On Off
B Off On Off On On Off On On On Off Off Off Off Off
C Off On On On Off On On Off Off Off On On Off On
D On Off On Off Off Off On On On Off On Off On On

Hardware Setup
9
CD-ROM Audio-in (CN2
Use the audio cable enclosed with your D-ROM disk drive to
connect the D-ROM to your mainboard. This will enable your
D-ROM's audio function.
Auxiliary Audio-in (CN3
This connector is for use with a secondary D-ROM, DVD-ROM
or DR/ DRW disk drive.
Optional Codec Audio Mono-in/out (CN4
This connector is used for Add on ard e.g. modem with Mono
in/out connector.
Optional Bass/Center Speaker Connector (CN4B
This connector is for enter+Bass speaker output ext. Plug in
the optional A 3 Surround enter+Bass jack extension into this
connector. The black colored jack is for surround speaker output
and the orange colored jack is for center+bass speaker output.
WOL (Wake-on-LAN Connector (CN5
Enable the Wake Up On LAN selection in BIOS's Power
Management Menu to use this function. This header is used
to connect an add-in NI (Network Interface ard) which gives
WOL capability to the mainboard.
Blue LED Connector(CN17
This feature work entirely the same as the power indicator LED,
both shows the system's power status. The only difference is that
this one is blue while the other is red LED.
USB 1/2 Ports and USB 3/4 Connector (USB1/CN20
If you want to use a USB Keyboard, you must enable the USB
keyboard support function in BIOS's Integrated Peripherals menu
(See Section 3-4). This board contains a USB Host controller and
includes a root hub with two USB 1/2 ports a connector for
optional USB Adaptor (USB 3/4).
Front Panel Audio Connector (CN22
This connector give you the option of a front panel audio jack
cable ext. to be plug into a special custom designed system case.
Simply remove the two jumper cap at pin 6-13 and 7-12 then plug
it into the (optional) cable ext. connector. Pin 6-13 and 7-12 are
shorted (default) to enabled the back panel audio function.
L
1
R
GND

Chapter 2
10
IR Connector (IR1
Select a UART Mode in BIOS's Integrated Peripherals menu the
UART port to support IR/ IR functions. (See section 3-4)
CPU/System Cooling Fan Connectors (FAN1/FAN2/FAN3
The board's management extension hardware is able to detect
the PU and system fan speed in rpm (revolutions per minute).
These connectors supports 3-pin cooling fans with minimum
of 4000 RPM. The wiring and plug may vary depending on the
manufacturer. On standard fans, the red is positive (+12V), the
black is ground, and the yellow wire is the rotation signal.
PS/2 Mouse and Keyboard Ports (PT1
If a PS/2 mouse is used, BIOS will automatically detect and assign
IRQ12 to the PS/2 mouse.
2-4 Main Memor Configuration
The DRAM memory system consists three banks and the memory size ranges from
32~512MBytes. If you only use one bank it does not matter which one you use and if
you use two or more banks, it does not matter which bank you install first.
DRAM Specifications
DIMM type: 3.3V, 64/72-bit Synchronous DRAM
Module size: Single/double-sided 32/64/128/256/512MBytes
DRAM speed: 7.5/10ns for Synchronous DRAM
Parity: Either parity or non-parity
This mainboard supports 3.3v, unbuffered, 4-clock, SDRAM DIMM only.
Buffered, 5V, or 2-clock SDRAM DIMMs should not be used.
Due to loading anomalies, using DIMM with an 'n x 4' DRAM base on this
mainboard is not recommended. For example, a DIMM that uses sixteen
16Mb x 4 devices should not be used.
Pin Definition
1Data
2No Connect
3Ground
4+5V (fused)
5Clock
6No Connect

11
Award BIOS Setup Program
Standard CMOS Features
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
+D=FJAH !
!
Award BIOS Setup Program
Award's BIOS ROM has a built-in setup program that allows users to modify the basic
system configuration. his information is stored in CMOS RAM so that it can retain
the setup information, even when the power is turned off.
When you turn on or restart the system, press the Delete key to enter the Award
BIOS setup program. he primary screen as shown in Figure 3-1 is a list of the menus
and functions available in the setup program. Select the desired item and press enter
to make changes. Operating commands are located at the bottom of this and all other
BIOS screens. When a field is highlighted, on-line help information is displayed on
the right side of the screen.
Select Item
Esc Quit
F10 Save & Exit Setup
Figure 3-1 Setup Program Initial Screen
Frequency/Voltage Control
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
Time, Date, Hard Disk Type...

User's Manual
12
3-1 Standard CMOS Features
he Standard CMOS Features allows users to configure system components such
as hard disk drive, floppy disk drive and video display as well as date, time and boot
up error signaling. his configuration menu should be changed when installing a
mainboard for the first time, changing hardware in your system such as the HDD,
FDD, video display, or when the CMOS data has been lost or contaminated. Choose
the Standard CMOS Setup option from the CMOS Setup Utility menu (Figure 3-1)
to display the following screen. When a field is highlighted, on-line help information
is displayed on the left bottom edge of the screen.
Date/Time
Set the date and time. Do not skip this function as all of your timed events such
as power management, saving files, etc. are based on this timer.
Hard Disk Setup (Primary/Secondary; aster/Slave)
his category identifies up to four IDE hard disk drives that have been installed in
the computer. his section does not show information on other IDE devices such
as CD-ROM drives or other hard drive types such as SCSI drives.
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
Sta dard CMOS Features
Item Help
Menu Level
Date (mm dd yy)
Time (hh mm ss)
IDE Primary Master
IDE Primary Slave
IDE Secondary Master
IDE Secondary Slave
Drive A
Drive B
Floppy 3 Mode Support
Video
Halt On
Base Memory
Extended Memory
Total Memory
Figure 3-2 Standard C OS Features Screen
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F :Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
Fri, Aug 31 2001
17 14 44
None
None
None
None
1.44M, 3.5 in.
None
Disabled
EGA/VGA
All Errors
640K
64512K
65536K

13
Award BIOS Setup Program
Floppy Disk Drives
Choose the memory capacity and disk size that corresponds with that of your floppy
disk drive(s).
Video
Select the type of video adapter present in your system. You can ignore this setting
if you are using a VGA monitor since VGA BIOS automatically configures this setting.
Halt
When the system is powered on, BIOS performs a series of diagnosis tests called
POS (Power On Self est). his function stops the computer if BIOS detects a
hardware error. You can tell BIOS to halt on all errors, no errors, or not to halt on
specific errors.

User's Manual
14
3-2 Advanced BIOS Features
By choosing the Advanced BIOS Features option from the CMOS Setup Utility menu
(Figure 3-1), the screen below is displayed. his sample screen contains the manufacturer's
default values for the mainboard.
A. HDD Instant Recovery
This board supports HDD Instant Recovery, select enabled to use this function.
Upon system boot up, the HDD Instant Recovery Utility will be shown on the
screen to let you install this utility. (See ppendix II)
B. Anti-Virus Protection
Trend +DEF)M=OVirus
rend ChipAway Virus is a code incorporated in the mainboard's BIOS firmware.
During the boot-up sequence, BIOS loads before loading of the partition table
or boot sector. ChipAway Virus loads with BIOS and is able to detect boot-up
viruses before they have a chance to infect the hard drive. ChipAway Virus
employs rule-based logic that doesn't look for specific viruses but rather detects
patterns found in every virus, eliminating the need to perform periodical version
updates after new viruses have been found.
Item Help
Menu Level
Figure 3-3 Advanced BIOS Features Screen
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
Adva ced BIOS Features
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F :Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
HDD Instant Recovery
Anti-Virus Protection
CPU Internal Cache
External Cache
CPU L2 Cache ECC Checking
Processor umber Feature
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up umLock Status
Typematic Rate Setting
X Typematic Rate (Chars/Sec)
X Typematic Delay (Msec)
Security Option
MPS Version Control For OS
Disabled
Disabled
Enabled
Enabled
Enabled
Enabled
Enabled
Floppy
HDD-0
LS120
Enabled
Disabled
Enabled
On
Disabled
6
250
Setup
1.4

15
Award BIOS Setup Program
C. Cache Control
CPU Internal Cache/External Cache
Cache memory is much faster than conventional DRAM system memory. hese
fields allow you to enable or disable the CPUs Level 1 built-in cache and Level
2 external cache. Both settings are left enabled to significantly increase the
performance of your computer.
D. Processor Number Feature
If you have Pentium III processor installed on the mainboard. Enable this option
allows the serial code inside the Pentium III processor to be published on certain
application.
E. Boot p Features
After turning on the system, BIOS will perform a series of device initialization and
diagnostic tests discussed below.
Quick Power On Self Test (POST)
Enable this function to reduce the amount of time required to run the POS (Power
On Self est). BIOS saves time by skipping some items during POS . It is
recommended that you disable this setting. Discovering a problem during boot
up is better than loosing data during your work.
First/Second/Third/Boot Other Device
his option sets the sequence of drives BIOS attempts to boot from after POS
completes. BIOS will search these drives for an operating system.
Swap Floppy Drive
Enabling this function will swap the floppy drive assignment so that drive A will
function as drive B, and drive B will function as drive A. Note that the boot
sequence assignment mentioned directly above does not include booting from
floppy drive B. his function is useful if floppy drives B and A are of a different
format and you want to boot from floppy drive B.
Boot up Floppy Seek
During POS , BIOS will determine if the installed floppy disk drive has 40 or 80
tracks. A 360K drive has 40 tracks and 720K, 1.2M and 1.44M drives have 80 tracks.
All modern floppy disk drives have 80 tracks.
Boot Up NumLock Status
his function defines the keyboard's number pad as number keys or arrow keys.
F. Keyboard Interface
Typematic Rate Setting
When enabled, you can set the following two typematic control items. When
disabled, keystrokes are determined arbitrarily by the keyboard controller in your
system.

User's Manual
16
Typematic Rate (Chars/Sec)
he typematic rate sets the rate at which characters on the screen repeat when
a key is pressed and held down.
Typematic Delay ( sec)
he typematic delay sets how long after you press a key that a character begins
repeating.
G. Security Option
he Supervisor and/or User Password functions shown in Figure 3-1 must be set
to take advantage of this function. See Section 3-11 for password setting
information. When the Security Option is set to System, a password must be
entered to boot the system or enter the BIOS setup program. When the Security
Option is set to Setup, a password is required to enter the BIOS setup program.
H. OS Select (For DRAM >64MB)
If your system's DRAM is larger than 64MB and you are running OS/2 , select
OS/2 as the item value. Otherwise, set the item value to Non-OS/2 for all other
operating systems.
I . Shadow Memory
Software such as system BIOS, video BIOS, SCSI BIOS, etc that resides in ROM
(Read Only Memory) chips is called firmware. Shadowing of firmware occurs when
BIOS is copied to RAM address C0000h through DFFFFh. Video BIOS loads into
the C0000-C7FFF memory area when video shadowing is enabled. If an expansion
peripheral in your system contains ROM-based firmware, you need to know the
address range the ROM occupies to shadow it into the correct area of RAM.
Shadowing improves the firmware's performance because the firmware can be read
by the CPU through the 16- or 32-bit DRAM bus as opposed to the 8-bit X bus.
However, shadowing also results in reducing the amount of high memory (640
KB to 1 MB) for loading device drivers. Shadowing is used mostly for ROM chips
on ISA cards and not for PCI cards. Shadowing and playing games at the same
time may result in system instability as some games access the RAM memory area
being shadowed.

17
Award BIOS Setup Program
Figure 3-4 Chipset Features Setup Screen
Item Help
Menu Level
CMOS Setup Utility- Copyright (C) 1984-2001 Award Software
Adva ced Chipset Features
:Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F :Previous Values F6:Fail-Safe Defaults F7:Optimized Defaults
3-3 Advanced Chipset Features
By choosing the Advanced Chipset Features option from the CMOS Setup Utility
menu (Figure 3-1), the screen below is displayed. his sample screen contains the
manufacturer's default values for the mainboard.
All of the above settings have been determined by the mainboard manufacturer
and should not be changed unless you are absolutely sure of what you are
doing. Explanation of the DRAM timing and chipset features setup is lengthy,
highly technical and beyond the scope of this manual. Below are abbreviated
descriptions of the functions in this setup menu. You can look on the world
wide web for helpful chipset and RAM configuration information including
AWARD's web site at http://www.award.com.
A. DRAM Timing By SPD
he function allows you to enable or disable the DRAM timing by SPD. When
Disabled, you can select the DRAM Clock, SDRAM Cycle Length and Bank
Interleave configuration.
B. SDRAM Cycle Length
When synchronous DRAM is installed, the number of the clock cycles of CAS
latency depends on the DRAM timing. Do not reset this setting from the default
value specified by the system designer.
Bank 0/1 DRAM Timing
Bank 2/3 DRAM Timing
Bank 4/5 DRAM Timing
DRAM Clock
SDRAM Cycle Length
Memory Hole
P2C/C2P Concurrency
System BIOS Cacheable
Video RAM Cacheable
AGP Aperture Size
AGP-4X Mode
AGP Driving Control
AGP Driving Value
Flash BIOS Protection
OnChip Sound
CPU to PCI Write Buffer
PCI Dynamic Bursting
PCI Master 0 WS Write
PCI Delay Transaction
SDRAM 10ns
SDRAM 10ns
SDRAM 10ns
Host CLK
3
Disabled
Enabled
Disabled
Disabled
64M
Enabled
Auto
DA
Disabled
Auto
Enabled
Enabled
Enabled
Enabled
X