Challenger APFSC User manual

Challenger_APFSC_Instructions_Rev01
APFSC
SMART CONTROL WIFI MODULE USER GUIDE
The APFSC Smart Control Wi-Fi module can be wired to a Force 10 / Force 48 intruder panel. The APFSC will
send alarm notifications via the building Wi-Fi to your Android™ or iOS® App.
1: Dual colour LED
Green Power
Red Data
2: Cover Screw
3: Learn Switch

Challenger_APFSC_Instructions_Rev01
Wiring diagram to Force10
Wiring diagram to Force10 with Integral Communicator Outputs
Note: When PIR or N.C. is not connected then the J7 jumper link should be moved to the left side.
When using PIR or NC, the J7 jumper link should be on the right side and Force10 in Full set Mode.
This port is not valid on disarm.

Challenger_APFSC_Instructions_Rev01
Important Note:
•Please ensure the relevant checks and calculations for the alarm system current loading has been
performed to ensure the control panel has enough current capacity to power the APFSC unit.
This will need to be calculated to ensure the control panel PSU is not exceed in quiescent and
alarm conditions (an additional separate PSU may be required).
•If you have a power cut or the power is lost to your router/Wi-Fi unit then the APFSC will be
unable to forward any notifications to your mobile device/App. Communication will also need to
be active to your internet provider.
•Ensure the APFSC is installed away from any other 2.4 GHz products, such as other wireless
networks, Bluetooth systems or microwave ovens, as interference could be an issue.
•The APFSC will not work and is not supported on 5ghz, ONLY2.4G Wi-Fi 802.11 b/g/n supported
•Ensure the appropriate location of the APFSC to ensure a good strong Wi-Fi connection.
HOW IT WORKS
The APFSC Wi-Fi dialer must be within range of the Wi-Fi® router with which you want to connect. After
binding between the device and the APP, you can get access the device status to monitor your property.
Installation
Prior to installing please ensure the check the desired location has a strong Wi-Fi signal.
Remove the outer cover and mount the backplate using appropriate fixings.
Mount to wall point

Challenger_APFSC_Instructions_Rev01
1. Set Up
App Download
System Requirement: Smartphones/Tablets with iOS 8.0, Android 6.0 or above.
Go to Google Play and Apple Store to search for "Keep Contact" and download the App
App Store (IOS):
Google Play Android):https://play.google.com/store/apps/details?id=com.leeds.menci
2User Account and Sensor Setup
There are two types of user accounts: “Main User”and “Sub User”. When registering and binding
the device to a Smartphones/Tablets with Dialer is defined as Main User. Then the “Main User”
can share the QR code with other Smartphones/Tablets for creating “Sub User”. Each APFSC dialer
can bind up to 1 “Main user”and “10 Sub users”.
Below is the summary of functions between Main and Sub user:
Item
Function/Feature
Main
User
Sub
User
Affect
Other User
Description
1
Change Device Name
●
Yes
Set the Dialer Name
2
Change Device Icon
●
●
No
Set the icon for the Dialer
3
Set Push Notification
●
●
No
Enable or Disable Push Notification (i.e. Arm/Disarm, endpoint alarm)
4
Bind Device
●
●
No
Bind User to Device. Email address is required for the binding. Main User set
the binding first and the Sub User use the QR code for binding
5
Unbind Device
●
●
Yes
Unbind User to Device. Please note that if Main User is unbound, the related
Sub User(s) will be unbound also.
6
Add User
●
No
Add User with QR Code
7
Delete User
●
No
Main User deletes the sub user
8
Display Weather Message
●
●
No
Display the weather information of coming 12 hours at the bottom of main
page
9
Check Arm/Disarm/Alarm
Record
●
●
No
Each Device keeps latest 60 records
10
Check Device Current Status
●
●
No
Check the status of the Dialer (Arm or Disarm and endpoint Status)

Challenger_APFSC_Instructions_Rev01
2.1. Sign Up, Login and Password Restore
2.1.1 Account Registration
An email address is required for the registration. Press “Register new account” ③ at the Login
page and follow the instructions to create your Account.
⚫input [Username], [Password] and [Email]
⚫click "Sign up" ④, the verification code will be sent to the email address
⚫input [Verification]⑤
⚫finally, click the “Confirm”⑥to complete the process
2.1.2 User Login
If you already have an APP account, please select "Login” ①by entering your user name and
password information and go to the next steps “Device List”⑦
2..1.3 Password Restore
If you forget your password? Click on the "Forget Password" ②at Login Page. The steps are
similar to Account Registration.
3. Connecting Devices
User may add a device through "Add Device" and "Scan QR code". Please note that there are no
devices at first login.
3.1 Use Keep Contact App for Connection
Ensure the dialer, mobile and router with a good signal (within 3 meters), Please note that 5Ghz
channel routing is not supported. Then, connect the mobile device to the same Wi-Fi you want the
APFSC to be connected too, (please ensure "Guest" networks are selected) perform the following
steps;

Challenger_APFSC_Instructions_Rev01
⚫Open the App “Keep Contact”and select "Add Device" ⑨. The SSID of Wi-Fi is displayed.
⚫Enter the Wi-Fi password
⚫Then, press and hold the [Program button] of the APFSC Dialer for 6 seconds. The Red LED ○ 12
will flash that the Dialer is now under connecting mode
⚫Click the “Start airlink” button on the App to start the connection process (please be patient).
If successful the LED will turn green and the App will display the below screen message, to
name the device and enter your disarm code, this code can be different to your alarm code.
⚫If the airlink failed to bind, then the LED flashes 60 seconds.
Note: The Red LED ○ 12 will be 'Green" color normally. It will be "Red" colour for 1 second when the
Dialer is triggered (Arm/Disarm/Endpoint alarm), the Dialer sends data to Server.
3.2 Scan QR Code
After the APFSC Dialer has been added, the main User can generate a QR code to allow another
user to register the device. The QR code is valid for approximately 10 minutes after being
generated. Other user opens the Keep Contact App and can scan this QR code to add this device.

Challenger_APFSC_Instructions_Rev01
4 Functions
4.1 Check Device Status
All registered Dialer(s) is displayed on "Device List" page ⑦. When you click one of the items, it
will enter the corresponding operation interface of the device ○
15 ,and shows the current status of
each device either at Arm or Disarm with icon (i.e. The Arm icon as ○ 17 ),The current status of each
terminal is shown on the right○
18 , which is indicated in different colors in front of the terminal
name ("green" indicates normal monitoring, "red" indicates an alarm is occurring, "black" indicates
that the terminal is not connected),○
19 Wi-Fi connected indicates that the connection to the Router
network is normal, and Wi-Fi disconnected indicates that the connection to the
Router network is not normal. Check if the Router network is normal every 2 hours
4.2 Arm Disarm
Click the button○
20 ○ 21 in the interface to arm or disarm the Force 10 /Force 48 alarm panel.
4.3 Set Device Attributes
Click the "Settings"○
22 button to enter the property setting interface○
24 of the device

Challenger_APFSC_Instructions_Rev01
⚫Device Name○ 25
⚫Device Icon○ 26
⚫Push Notification○ 27
⚫Change disarm password○ 28
⚫Endpoint name○ 29
Once finished, click [Save]○ 30 to store the setting
*** Main User and Sub User have different privilege for the setting, Gray display indicates that the
current user does not have right to set ***
4.4 Change Device Name and Icon
The Dialer can be named according to user preference (i.e. Main Door, refrigerator.....etc). Only
Main user has right for the setting. The Icon can be set by both Main and Sub user
4.5 Enable and Disable the Open/Close Push Notification
Main and Sub user can enable and disable the Open/Close Push Notification of each Dialer
Installed individually.
4.6 Change disarm password
Users corresponding to the device can change the password. The password only works when the
current user operates disarm
4.7 Set endpoint name
Only Main user can set the endpoint name, Main user can set the corresponding name as
required

Challenger_APFSC_Instructions_Rev01
4.8 Check alarm event
Alarm event including arm, disarm and endpoint alarm
Both Main and Sub user can check the alarm event. Click the “Event”○ 23 to check the latest 60
alarm events as below:
4.09 Manage Sub User
Only Main user can manage Sub user, include add and delete user; Click the “Management”○
15,
the menu will be displayed as
⚫Select "Add user"○ 31 , the QR code○ 33 will be displayed (valid for around 10 minutes). Other
Keep Contact app user scan the QR to create the Sub user to monitor the Dialer
⚫Select "Delete user", those email address of Sub users is listed and click the Delete ○ 34 at the
corresponding email address to remove the Sub user. And then, select "Close"○ 35 to exit.

Challenger_APFSC_Instructions_Rev01
5. Specifications
Power Supply:
DC 9~14V
Work Current
Trigger 200mA Max
Stand-by Current
30mA
Transmission range:
20 meters (open air with direct line of sight)
Transmission frequency:
2.4G Wi-Fi 802.11 b/g/n supported
Smartphones/Tablets:
iOS® and Android™ only
System Requirement:
iOS® 8.0, Android™6.0 or above.