ESI AA750DAT Operating and maintenance manual

INSTALLATION AND USE
AA750DAT
ARTICULATING KEYBOARD ARM
AA750DAT Rev A 4/17
Model AA750DAT

2
AA750DAT ARTICULATING KEYBOARD ARM
PLEASE REVIEW these instructions before beginning the installation. Check that
all parts needed were provided with your order. Contact your supplier if any
operates to your satisfaction.
PARTS PROVIDED
CAUTION: This install
T RACK MOUN T IN G T EM P LA T E
FRONT E DG E OF WORK S UR FA CE
1. Tapethis mo
untin
gtemplateto
th
e undersideof work surface.
2. Drilltwo(2) 1/8"diamete
r x 1/2" deeppilot holesat markedloc
ations. Be carefulnotto
drillthroughthe work surface.
3. Remov
e temp
lateandinstall two (2) #12x 3/4" woodscrewsi nto
pilot holes. Leave a gap
ofapproxim
ately1/8" betweentheheadof each screwand work surface.
4. Slid
etrackontoscrew
s, usingth
ekeyhol
es in the track. Tighten t he screws andinstall
additio
nalscrews as required,mi
nim
umof four (4).
Note: If keyboar
dtrayis deeper than12", mountbaseframea furth
er 1/2" backfromth
efront
edge of work s urface.
1/8" PilotHole
1/8" PilotHole
Articulating Arm (1) Track (1)
12x3/4" Screws (8)
10x3/8" Screws (2)Front Stop (1)Template (1)
ADDITIONAL TOOLS REQUIRED
•
#3 Phillips Screw Driver Bit
•
STEP 1: Use Template to Drill Pilot Holes
• Tape the template to the underside of the work
surface. Align the “front edge” line on the
template with the front edge of the
work surface.
• Drill 1
/8" pilot holes through the
two marked locations on the
template.
— Drill the holes 5/8" deep
CAUTION: Be careful not to drill
through the work surface.
Tape to Underside
of Work Surface
requires a power drill.
This is not a hand tool
install.
•
#2 Square Phillips Bit
Drill with 1 /8" bit

3
AA750DAT ARTICULATING KEYBOARD ARM
STEP 2: Attach Track
• Remove the template and install two 3/4" wood screws into the pilot holes.
— Leave a gap of approximately 1 /8" between the head of each screw and
the work surface
• Slide the track onto the screws, using the keyholes in the track. Tighten the
screws.
• Drill pilot holes for six additional screws spaced evenly along the track.
Fasten the screws to complete the installation of the track.
Slide Small Portion
of Keyhole Under
Screw and Tighten
1
/8"

4
Slide Back
AA750DAT ARTICULATING KEYBOARD ARM
STEP 3: Install Articulating Arm
• Slide the articulating arm onto the track.
Position it back far enough so that
you have access to the front two
recessed holes on the track.
STEP 4: Attach Front Stop
• Position the front stop onto the
front of the track and secure it
with the 3/8" machine screws.
Front
Stop
3/8"Machine
Screw

OPERATION
To Raise:
• Grasp both sides of the platform and raise to the desired height.
To Lower:
• Grasp both sides of the platform, tilt up the front, and move down to the
desired height.
To Tilt:
• Turn the handle clockwise to tilt the platform up.
• Turn the handle counterclockwise to tilt the platform down.
AA750DAT ARTICULATING KEYBOARD ARM
© 2017 ESI Ergonomic Solutions. All rights reserved. AA750DAT Rev A 4/17
800.833.3746 esiergo.com