Champion D-H1T User manual

(1M) 10/06 rinted in U.S.A.
CH079
Door-type High Temperature
Extended Hood Gas Heated
Warewashing Machine
D-H1T GAS
D-H1T GAS DOOR-TYPE
STANDARD FEATURES
• Dual NSF listing as a dishwasher and pot,
pan, utensil washer
• Automatic tank fill
• Automatic drain valve
• Adjustable mode/time selector switch
• Door activated cycle start
• One gas heating system for boosting
the final rinse and tank heat
• Low-water tank heat protection
• 2-Hp pump motor
• Stainless steel pump impeller
• Door safety switch
• Interchangeable upper and lower spray arms
• Vented wash chamber design
• Detergent/chemical connection provisions
• Single point electrical connection (see chart)
SPECIFIER STATEMENT
Specified unit will be Champion Industries model
D-H1T door type extended hood, gas tank heat,
high temperature dishwashing machine.
Features include automatic tank fill, automatic drain
valve, 2 Hp drip-proof pump motor, gas tank heat,
interchangeable upper and lower spray arms, door
activated start cycle, dual NSF Certified as both
dishwasher and potwasher.
1 year parts and labor warranty.
OPTIONS & ACCESSORIES
Corner Model
Drain Tempering Kit
Vent Fan Control Switch
roject
Item No.
Quantity
Champion Industries, Inc.
. O. Box 4149, Winston-Salem, NC 27115
Tel: [phone] Fax: [phone]
www.championindustries.com
Gas
Dual Certified!

Door-type Extended Hood
Gas Heated
High Temperature Dishwasher
D-H1T GAS DOOR-TYPE
Dimensions shown in inches
1A
5A
7
2−5/8"
19−7/8"
2 HP 12−1/2"
67−1/2"
34"
27"
13−1/4"
25−1/4"
Clearance
92−1/2"
Door Removal
87"
Door Up
31−1/4" 10−1/4"
25−7/8"
8−1/2" 7−1/8"
1A
5A
1
7
2A 61B
3
*Hatco
Gas Booster
Mod. #PMG−100
8−7/8"
D tails, Dim nsions & Conn ctions
Front Vi w
Sid Vi w
Note: The booster and machine come fully interplumbed
complete with a blended phosphate water treatment
system, pressure regulating valve, water hammer
arrestor, ASME temperature and pressure relief valve,
drain valve, circulator pump, and temperature gauges
installed and ready for connection to your water supply.
Utiliti s
1Electrical
A. Machine Connection (See Box)
B. Booster connection requires 15 Amps @ 120/60/1
2Hot Water
3/4" NPT hot water 140°F for 40°F rise booster.
3/4" NPT hot water 110°F for 70°F rise booster.
Flow pressure 20-22 psi.
3Drain
A. 2" OD machine connection
B. 3/4" NPT relief valve to open drain
C. 1/2" NPT vent to open drain
D. 3/4" male threaded hose end
4Gas
40°F rise - 58,000 BTU/hr.
70°F rise - 105,000 BTU/hr.
PMG-60 requires 1/2" NPT.
PMG-100 requires 3/4" NPT.
5Gas Flue 4" OD exhaust
A. Rear of booster
ength between table connections: 25-3/4"
Shipping weight crated: 775 lbs.
1−1/
4" Roll
1−1
/8"
24−
1/4"
20−
7/8"
7−1/4
"
2−1/8
"
Typical Tabl Construction
* Booster shown is the PMG100. Contact factory
for PMG60 drawings & electrical information.
Machine Loa Amps Minimum Maximum
Supply Ckt. Overcurrent
Rate Con uctor Protective
Voltage Amps Ampacity Device
208/60/1 15 20 20
240/60/1 14 20 20
208/60/3 8 15 15
240/60/3 7 15 15
480/60/3 4 15 15
575/60/3 3 15 15
Gas

Door-type Extended Hood
Gas Heated
High Temperature Dishwasher
D-H1T GAS DOOR-TYPE
Due to an ongoing value analysis program at Champion, specifications contained in this catalog are subject to change without notice.
Champion Industries, Inc., P. O. Box 4149, Winston-Salem, NC 27115 • 336/661-1556 • Fax: [phone] • www.championindustries.com
SPECIFICATIONS
Capacities
Wash tank US gal. 9
Dishwasher Mode:
NSF Rated Racks per hr. 49/29
Pot/Pan Washer Mode:
NSF Rated Racks per hr. 19/10
Motor horsepower 2
Water consumption
Gal. per rack US gal. 1.34
Gal. per hr. (max. use) US gal. 66
Temperature°F/°C
Wash 150/66
Rinse 180/82
Heating
Gas PMG60 (40°F rise) 58,000 BTU/hr
PMG100 (70°F rise) 105,000 BTU/hr
Time Cycle in Secon s
Dishwasher Mo e Pot/Pan Washer Mo e
Wash 44 96 Wash 156 336
Rinse 13 13 Rinse 13 13
Dwell 11 11 Dwell 11 11
Total 68 120 Total 180 360
Warning: Plumbing and electrical connection should be made by qualified
personnel who will observe all the applicable plumbing, sanitary and safety
codes and the National Electrical Code.
Warning: Gas burner intake air and exhaust venting required in accordance
with local codes. Exhaust must be vented outside.
Note: Specify vent location option on booster when ordering.
Dimensions shown in inches
Front
2
20-1/8"
Inside Tracks 2-7/8"
5-1/4" min
Straight-Through
Op ration
Corn r
Configuration
Plan Vi w
26−3/4"
10"
63−1/2"
27−1/2"
26−1/2"
13"
44−5/8"
5−3/4"
MIN. 5−1/4"
26"
41"
24−5/8"
25−5/8"
2"
Gas Booster
7
2A
61B
20−3/4"
8−1/4"
1
31−3/4"
2
Gas
5-1/4" Min.
20-1/8"
Inside
Tracks
2-7/8"
Front
5-1/4" Min.
3-1/4"
9-1/4"
1
5"
Control
Cabinet

Door-type High Temperature
Extended Hood Gas Heated
Warewashing Machine
D-H1T GAS
D-H1T GAS DOOR-TYPE
C rner C nfigurati n
D-H1T C rner Unit
Sh wing 90° M unted
C ntr l Panel
Due to an ongoing value analysis program at Champion, specifications contained in this catalog are subject to change without notice.
Champion Industries, Inc., . O. Box 4149, Winston-Salem, NC 27115 • 336/661-1556 • Fax: [phone] • www.championindustries.com
Gas