Champion 102006 User manual

INSTALLATION MANUAL
SERVICE ENTRY WHOLE HOUSE
AUTOMATIC TRANSFER SWITCH (ATS)
All aXis Controller®Models
REV 20231227 Champion Power Equipment, Inc.
or visit championpowerequipment.com
READ AND SAVE THIS MANUAL. This manual contains important safety precautions which should be read and understood before operating the product. Failure to
do so could result in serious injury. This manual should remain with the product.
Specifications, descriptions and illustrations in this manual are as accurate as known at the time of publication, but are subject to change without notice.
REGISTER YOUR PRODUCT ONLINE
at championpowerequipment.com

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS TABLE OF CONTENTS
2
TABLE OF CONTENTS
Introduction...................................................3
Safety Definitions ..........................................3
Important Safety Instructions.......................4
Instructions for Champion Automatic Transfer Switch with aXis
Controller®Module................................................4
Before Installation.................................................4
Safety Labels......................................................5
Safety Symbols....................................................6
Controls and Features ...................................7
Champion Automatic Transfer Switch with aXis Controller®
Module.............................................................7
Unpacking......................................................8
Location and Mounting ...........................................8
Electrical Grommet(s) .............................................8
Installation Wiring for ATS Utility Socket .........................8
Installation ....................................................9
Wiring the ATS ....................................................9
Battery Charger Wiring.......................................... 10
Utility Sensing Fuse Block ...................................... 10
Low Voltage Control Relays..................................... 10
Settings on the aXis Controller®Module........................11
400A Installation ................................................ 12
Primary ATS LEDs............................................... 14
Secondary ATS LEDs............................................ 14
Wi-Fi Setup Method............................................. 15
ATS and HSB Status Using WI-FI............................... 17
Connecting the Load Management Systems................... 17
Teaching System ................................................ 17
Full System Check .............................................. 18
Specifications.............................................. 19
Technical Specifications ........................................ 19
102006, 102007, 102008, 102009,
102010 ATS Wiring Diagram.................................... 20
Warranty......................................................21

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS INTRODUCTION
3
INTRODUCTION
Congratulations on your purchase of a Champion Power Equipment
(CPE) product. CPE designs, builds, and supports all of our
products to strict specifications and guidelines. With proper
product knowledge, safe use, and regular maintenance, this
product should bring years of satisfying service.
Every effort has been made to ensure the accuracy and
completeness of the information in this manual at the time of
publication, and we reserve the right to change, alter and/or
improve the product and this document at any time without prior
notice.
CPE highly values how our products are designed, manufactured,
operated, and serviced as well as providing safety to the operator
and those around the generator. Therefore, it is IMPORTANT to
review this product manual and other product materials thoroughly
and be fully aware and knowledgeable of the assembly, operation,
dangers and maintenance of the product before use. Fully
familiarize yourself, and make sure others who plan on operating
the product fully familiarize themselves too, with the proper safety
and operation procedures before each use. Please always exercise
common sense and always err on the side of caution when
operating the product to ensure no accident, property damage,
or injury occurs. We want you to continue to use and be satisfied
with your CPE product for years to come.
When contacting CPE about parts and/or service, you will need to
supply the complete model and serial numbers of your product.
Transcribe the information found on your product’s nameplate
label to the table below.
CPE TECHNICAL SUPPORT TEAM
1-877-338-0999
MODEL NUMBER
102006, 102007, 102008, 102009, 102010
SERIAL NUMBER
DATE OF PURCHASE
PURCHASE LOCATION
SAFETY DEFINITIONS
The purpose of safety symbols is to attract your attention to
possible dangers. The safety symbols, and their explanations,
deserve your careful attention and understanding. The safety
warnings do not by themselves eliminate any danger. The
instructions or warnings they give are not substitutes for proper
accident prevention measures.
DANGER
DANGER indicates a hazardous situation which,if not avoided,
will result in death or serious injury.
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
NOTICE
NOTICE indicates information considered important, but not
hazard-related (e.g., messages relating to property damage).

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS IMPORTANT SAFETY INSTRUCTIONS
4
IMPORTANT SAFETY INSTRUCTIONS
WARNING
Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Instructions for Champion Automatic
Transfer Switch with aXis Controller®Module
THE CHAMPION AUTOMATIC TRANSFER SWITCH WITH aXis
CONTROLLER®MODULE IS NOT FOR “DO-IT-YOURSELF”
INSTALLATION. It must be installed by a qualified electrician
thoroughly familiar with all applicable electrical and building
codes.
This manual has been prepared for familiarizing servicing dealer/
installer with the design, application, installation and servicing of
the equipment.
Read the manual carefully and comply with all instructions.
This manual or a copy of this manual should remain with the
switch. Every effort has been taken to make sure that the contents
of this manual are accurate and current.
The manufacturer reserves the right to change, alter or otherwise
improve this literature and the product at any time without prior
notice and without any obligation or liability whatsoever.
The manufacturer cannot anticipate every possible circumstance
that might involve a hazard.
The warnings in this manual, tags and decals affixed to the unit
are, therefore, not all-inclusive. If using a procedure, work method
or operating technique the manufacturer does not specifically
recommend follow all codes to ensure safety for personnel.
Many accidents are caused by failing to follow simple and
fundamental rules, codes and precautions. Before installing,
operating or servicing this equipment, read the SAFETY RULES
carefully.
The publications that cover the safe use of ATS and installation
are the following NFPA 70, NFPA 70E, UL 1008 and UL 67. It is
important to refer to the latest version of any standard/code to
ensure correct and current information. All installations must
comply with local municipal, state and national codes.
Before Installation
WARNING
Per OSHA 3120 Publication; “lockout/tagout” refers to
specific practices and procedures to safeguard individuals
from the unexpected energization or startup of machinery
and equipment, or the release of hazardous energy during
installation, service or maintenance activities.
DANGER
Be certain that the power from the utility is turned off and all
backup sources are locked out before starting this procedure.
Failure to do so could result in serious injury or death. Be
aware, automatic start generators will start upon loss of utility
mains power unless locked in the “off” position.
Consult the generator operator manual section to locate the
ATS CONTROL and ENGINE CONTROL modules to make sure
both switches are in the OFF position.
CAUTION
Consult with your Local municipal, State and National
electrical codes for proper mandatory wiring methods.

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS IMPORTANT SAFETY INSTRUCTIONS
5
Safety Labels
These labels warn you of potential hazards that can cause serious injury. Read them carefully.
If a label comes off or becomes hard to read, contact Technical Support Team for possible replacement.
HANGTAG/LABEL DESCRIPTION PART NUMBER
1
1681-T- PR
ATTENTION
ALTERNATE POWER SOURCE AVAILABLE -
STANDBY GENERATOR ON PREMISES.
ATTENTION
AUTRE SOURCE DE COURANT DISPONIBLE -
GENERATEUR SUR SITE.
ATENCIÓN
FUENTE DE CORRIENTE ALTERNA DISPONIBLE -
GENERADOR DE RESERVA EN EL SITIO.
GENERATOR LOCATION:
UBICACIÓN DEL GENERADOR:
EMPLACEMENT DU GENERATEUR:
DO NOT REMOVE \ NO REMUEVA \ NE PAS ENLEVER
NW
W E
NNE
SW SSE
1681-T- PR
ATTENTION
ALTERNATE POWER SOURCE AVAILABLE -
STANDBY GENERATOR ON PREMISES.
ATTENTION
AUTRE SOURCE DE COURANT DISPONIBLE -
GENERATEUR SUR SITE.
ATENCIÓN
FUENTE DE CORRIENTE ALTERNA DISPONIBLE -
GENERADOR DE RESERVA EN EL SITIO.
GENERATOR LOCATION:
UBICACIÓN DEL GENERADOR:
EMPLACEMENT DU GENERATEUR:
DO NOT REMOVE \ NO REMUEVA \ NE PAS ENLEVER
NW
W E
NNE
SW SSE
FRONT BACK
K---------
ColorsLPN 168 1-T-O P
Rev --
Size 115 x 110 mm
Artwork Notes
2mm safe m argin; fron t and back; to be p rinted on
weather-resistant, white, synthetic substrate (PE/PP
mix)
Revision Changes
--
This artw ork belongs to Champio n Power Equipment. The c ontents are confi dential and privileg ed and shall not be disclo sed to or used by or for
outside par ties without the e xplicit consent of C hampion Power Equip ment.
152
Alternate Power Source
1681-T-OP
(2 per unit)
Loose in IM bag.
2
This switch will not transfer if overcurrent device
opens due to fault.
 CAUTION
Cet interrupteur ne sera pas transfere si le
dispositif a maximum de courant
s’ouvre par errur.
 MISE EN GARDE
Este interruptor no se transferira si el dispositivo
de sobrecorriente se abre debido a una falla.
 PRECAUCIÓN
1943-L-PR-A
K109 --- --- ---
ColorsLPN 1943-L-PR
Rev A
Size 70 x 26 mm
Artwork Notes
3mm corner radius; 2mm safe margin; to be printed
on
white substrate.
Revision Changes
---
This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for
outside parties without the explicit consent of Champion Power Equipment.
Caution. Overcurrent device. 1943-L-PR
3
Electrical shock hazard. May cause injury or death.
Disconnect all sources of supply before servicing.
Riesgo de descarga eléctrica. Puede causar lesión o la
muerte. Desconecte todas las fuentes de suministro
antes de realizar el servicio.
Risque d'électrocution. Peut causer des blessures ou la
mort. Débranchez toutes les sources d'alimentation
avant de procéder à l'entretien.
2458-L-PR-A
More than one live circuit - disconnect all sources of supply before servicing.
Más de un circuito en vivo - desconecte todas las fuentes de
suministro antes de dar servicio.
Plusieurs circuits sous tension - débranchez toutes les sources
d’alimentation avant de procéder àl’entredien.
WARNING ADVERTENCIA AVERTISSEMENT
DANGER PELIGRO DANGER
K485 152 --- ---
ColorsLPN 2458-L-PR
Rev A
Size 90 x 65 mm
Artwork Notes
3mm corner radius; 2mm safe margin; to be printed
on
WHITE substrate.
Revision Changes
---
This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for
outside parties without the explicit con sent of Champion Power Equipment.
Danger. Electrocution shock hazard.
Warning. More than one live circuit. 2458-L-PR
4
3454-L-SF-A
WARNING ADVERTENCIA AVERTISSEMENT
Shock hazard exists if grounding electrode conductor or bonding
jumper connection in this equipment is removed while alternate
source(s) is energized.
Existe peligro de choque si se elimina el conductor del electrodo de
conexión a tierra o la conexión del puente de unión en este equipo
mientras se energizan las fuentes alternativas.
Il existe un risque d'électrocution si le conducteur de l'électrode de
mise à la terre ou la connexion du cavalier de liaison de cet
équipement est retiré alors que la ou les autres sources sont
sous tension.
K---152 --- ---
ColorsAPN 3454-L-SF
Rev A
Size 90 x 65 mm
Artwork Notes
3mm corner radius; 2mm safe margin; to be printed
on
WHITE substrate.
Revision Changes
---
This artwork belongs to Champion Power Equipment. The contents are confidential and privileged and shall not be disclosed to or used by or for
outside parties without the explicit consent of Champion Power Equipment.
ATS Ground Hazard
3454-L-SF
(1 per unit)
Loose in IM bag.

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS IMPORTANT SAFETY INSTRUCTIONS
6
Safety Symbols
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these
symbols will allow you to more safely operate the product.
SYMBOL MEANING
Read Installation Manual. To reduce the risk of injury, user must read and understand installation
manual before using this product.
Ground. Consult with local electrician to determine grounding requirements before operation.
Electric Shock. Improper connections can create an electrocution hazard.

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS CONTROLS AND FEATURES
7
CONTROLS AND FEATURES
Read this installation manual before installing your transfer switch. Familiarize yourself with the location and function of the controls and
features. Save this manual for future reference.
Champion Automatic Transfer Switch with aXis Controller®Module
1. aXis Controller
2. Antenna
3. Generator L1 and L2 Terminals
4. Battery Charger Fuse Block
5. Two Wire Sensing Fuse Block - Used only with a non-
Champion HSB
6. Ground Bar
7. Neutral Bar
8. Neutral to Ground Bonding Wire
9. Load L1 and L2 Terminals
10. Utility L1 and L2 Terminals
11. Mounting Holes
12. Front Cover
13. Dead Front
14. Utility Access Panel (if applicable)
1
5 6 7
12
14
2
3
4
11
11 11
8
11
9
10
Models 102006/102008/102009
Models 102007/102010
13

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS UNPACKING
8
UNPACKING
1. Use care when unpacking to avoid damaging transfer switch
components.
2. Allow the ATS to acclimate to room temperature for
a minimum of 24 hours before unpacking to prevent
condensation on the electrical apparatus.
3. Use a wet/dry vacuum cleaner or a dry cloth to remove dirt
and packing material that may have accumulated in the
transfer switch or any of its components during storage.
4. Do not use compressed air to clean the switch, cleaning with
compressed air can cause debris to lodge in the components
and damage the switch per the ATS manufacturers
specifications.
5. Retain the ATS manual with or near the ATS for future
reference.
TOOLS REQUIRED NOT INCLUDED
5/16 in. Hex Wrench Mounting Hardware
Line Voltage Wire
1/4 in. Flat Screwdriver Conduit
Fittings
Location and Mounting
Install the ATS as close as possible to utility meter socket. Wires
will run between the ATS and main distribution panel, proper
installation and conduit are required by code. Mount the ATS
vertically to a rigid supporting structure. To prevent the ATS or
enclosure box from distortion, level all mounting points; use
washers behind the mounting holes (outside the enclosure,
between enclosure and supporting structure), see following image.
The recommended fasteners are 1/4” lag screws. Always follow
local code.
16 in.
406.4 mm
24 in.
609.5 mm
16 in.
(406.4 mm)
24 in.
(609.5 mm)
Electrical Grommet(s)
Grommets can be used in any enclosure knockout for NEMA 1
installations. Grommets can only be used in the bottom enclosure
knockouts for NEMA 3R installations, when installed outside.
Installation Wiring for ATS Utility Socket
WARNING
The manufacturer recommends that a licensed electrician or
an individual with complete knowledge of electricity perform
these procedures.
Always be certain that the power from the main panel is
turned “OFF” and all backup sources are locked out prior to
removal of the cover or removal of any wiring of the utility
main electrical distribution panel.
Be aware, automatic start generators will start upon loss of
utility main power unless locked in the “OFF” position.
Failure to do so could result in serious injury or death.
CAUTION
Consult with your Local municipal, State and National
electrical codes for proper mandatory wiring methods.
Conductor sizes must be adequate to handle the maximum current
to which they will be subjected. The installation must comply fully
with all applicable codes, standards and regulations. Conductors
must be properly supported, of approved insulation materials,
protected by approved conduit and with the correct wire gauge
size in accordance with all applicable codes. Before connecting
wire cables to terminals, remove any surface oxides from the
cable ends with a wire brush. All power cables must enter the
enclosure through the enclosure knockouts.
1. Determine where the flexible, liquid tight conduit will pass
through the building from the inside to outside. When you
are certain that there is adequate clearance on each side of
the wall, drill a small pilot hole through the wall to mark the
location. Drill an appropriate sized hole through the sheathing
and siding.
2. In compliance with all local electrical codes, route the conduit
along ceiling/floor joists and wall studs to the location where
the conduit will pass through the wall to the exterior of the
house. Once the conduit is pulled through the wall and in
proper position to attach to the HSB generator, place silicone
caulk around the conduit on both side of the hole, inside and
outside.
3. Mount the ATS near the Utility meter socket.

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS INSTALLATION
9
INSTALLATION
Wiring the ATS
NOTICE
US ATS model shown for reference. For Canadian installation,
refer to ATS Installation Manual.
NOTICE
The aXis ATS controls the automatic startup and shutdown
of the aXis HSB using Power Line Communication (PLC).
The PLC system utilizes the L1 and L2 power wires that run
between the ATS and HSB for communication. As a result,
there are no wires that need to be run between the ATS
and HSB besides the power wires (L1, L2, N, G) and battery
charger wires mentioned in this manual.
1. Have authorized utility personnel pull the utility meter from
the meter socket.
2. Remove door and dead front of ATS.
3. Connect Utility (L1-L2) to ATS Utility side breaker. Torque to
275 in-lbs.
4. Connect Utility N to Neutral lug. Torque to 275 in-lbs.
5. Connect earth GROUND to GROUND bar. NOTE: GROUND and
NEUTRAL bonded in this panel.
6. Connect Generator L1-L2 to Generator side breaker. Torque to
45-50 in-lbs.
7. Connect Generator Neutral to neutral bar. Torque to
275 in-lbs.
8. Connect Generator Ground to ground bar.
Torque to 35-45 in-lbs.
9. Connect Load bars L1 and L2 to distribution panel.
Torque to 275 in-lbs.
10. Pull NEUTRAL from ATS to distribution panel. Pull GROUND
from ATS to distribution panel.
CAUTION
Remove bond from distribution panel if installed.

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS INSTALLATION
10
Battery Charger Wiring
The aXis Controller®HSB contains a 24V battery charger that is
powered by 120V AC. The battery charger receives 120V AC power
from the aXis Controller®ATS using the single fuse block located
in the bottom left corner of the ATS.
1. Run two wires from the ATS to the HSB for the battery
charger circuit.
The battery charger circuit is 120V AC, 1 amp maximum.
Wires need to be sized accordingly.
Wiring can run in the same conduit as the L1, L2, Neutral and
Ground wires from the previous section provided:
1a. Battery charger wire has an insulation rating equal to or
greater than 264VAC.
1b. Battery charger wire is suitable for outdoor installation.
1c. Allowed by local code and meets NFPA 70.
2. ATS Connections for battery charger.
2a. L1 - Bottom terminal of the fuse block in the ATS.
2b. Neutral - Neutral block.
See picture below for location of fuse block and neutral block.
3. HSB Connection for battery terminals
3a. L1 and N will connect to a terminal located near
the connection points of L1, L2, N, and G. Refer to
aXis controller™ HSB installation manual for more
information.
Utility Sensing Fuse Block
The utility sensing fuse block is not used in a typical installation.
The fuse block is only used when connecting the Champion aXis
ATS to a non-Champion HSB that monitors utility voltage to control
automatic generator start/stop. The potential voltage between the
two fuses is 240V AC.
Do not use the utility sensing block for the battery charging circuit.
The battery charging fuse block is located next to the utility
sensing fuse block.
Low Voltage Control Relays
The aXis Controller®ATS has two low voltage relays that can be
used to manage the load of air conditioners or other devices that
utilize low voltage controls. The ATS’s two low voltage relays are
called AC1 and AC2 and are found on the aXis control board as
shown in the picture below.
AC 2
Pin 1 Pin 2 Pin 3 Pin 1 Pin 2
AC 1
CONNECTING TO AC1 AND AC2
For air conditioner or other low voltage controls, route your low
voltage wiring into the ATS using code appropriate conduit and
fittings. Connect the wiring to pin 1 and pin 2 of either AC1 or AC2
as shown in the diagram above. Please note that AC2 has three
pins available, of which, pin 3 is not used.

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS INSTALLATION
11
Settings on the aXis Controller®Module
1. On the aXis control board, set the two circular pots that
are located to the right of the DIP switches to match the
maximum power output of the generator for your fuel type.
1st pot (left pot) is 10’s value, 2nd pot (right pot) is 1’s value, do
not go over generator rating. If wattage rating of generator falls
between settings choose the next lower value; i.e. generator
rating is 12,500W, set pots to 1 and 2 for 12,000W.
NO
1 2 3 4 5 6 7 8 9 10 11 12
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9
NOTICE
All DIP switches are set to ON by default from the factory
except for switch #9 which is set to OFF.
2. Verify the DIP switches are set for your installation. Adjust as
needed.
DIP Switch Settings
Switch 1. Load Module 1 Lockout
–On= Load Module 1 is being managed. Load Module 1 is the
lowest priority of the 4 load modules. This load will be turned
off first as the ATS manages the home’s load.
–Off= Load module 1 will stay off during HSB power.
Switch 2. Load Module 2 Lockout
–On= Load Module 2 is being managed.
–Off= Load module 2 will stay off during HSB power.
Switch 3. Load Module 3 Lockout
–On= Load Module 3 is being managed.
–Off= Load module 3 will stay off during HSB power.
Switch 4. Load Module 4 Lockout
–On= Load Module 4 is being managed. Load Module 4 is the
highest priority of the 4 load modules. This load will be turned
off last as the ATS manages the homes load.
–Off= Load module 4 will stay off during HSB power.
Switch 5. Frequency Protection.
–On= All managed loads will be turned off when if the HSB
frequency drops below 58 Hz.
–Off= All managed loads will be turned off when if the HSB
frequency drops below 57 Hz.
Switch 6. Spare. Not used at this time. Switch position does not
matter.
Switch 7. Power Management
–On= ATS is managing the homes load.
–Off= ATS has disabled power management.
Switch 8. PLC vs. Two Wire Communication
–On= ATS will control HSB startup and shutdown through PLC.
This is the preferred method of communication however it
requires the HSB to be an aXis controlled HSB.
–Off= ATS will control the start of the HSB using the AC2 Relay.
In this setting the AC2 can not be used to manage a load. Pins
1 and 3 of the AC2 connector will be used for the HSB startup
signal.
Switch 9. Test HSB with Load
–On= Test occurs with load.
–Off= Test occurs without load.
Switch 10. Primary/Secondary
–On= This ATS is the primary or only ATS. <- most common.
–Off= This ATS is being controlled by a different aXis
controller®ATS. Used for installations that require two ATS
boxes (i.e. 400A installations).
Switch 11. Exercise Test
–On= Exercise tests will occur per the schedule that is
programmed into the aXis controller.
–Off= Exercise tests are disabled.
Switch 12. Time delay for HSB to accept load.
–On= 45 seconds.
–Off= 7 seconds.
3. Have authorized utility personnel reconnect the utility meter
to the meter socket.
4. Verify voltage at utility circuit breaker.
5. Turn on utility circuit breaker.
6. ATS aXis Controller®module will begin boot up process.
Allow ATS aXis Controller®module to fully boot up
(approximately 6 minutes).
7. Home should be fully powered at this point.

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS INSTALLATION
12
400A Installation
The following instructions are for installing two (2) 200A ATSs,
allowing 400A service.
Primary ATS installed and connected to primary distribution
panel as shown in the Installation Manual for the aXis Controller®
Automatic Transfer Switch (ATS), in “Wiring the ATS.”
Secondary ATS installed and connected to secondary distribution
panel as shown below.
Models affected
–100515- 14-kW aXis Home Standby Generator
–102006 - 200A ATS
–102007 - 200A ATS
HSB output (L1, L2, N, G) must be brought to a junction box
(customer supplied) and split to supply both primary ATS and
secondary ATS.
WARNING
Have only qualified personnel who are familiar with applicable
codes, standards and regulations install and service the
generator. ALWAYS comply with local, state, province, or
territory and national electrical and building codes when
installing the generator. NEVER alter the recommended
installation in a way that would render the unit noncompliant
with these codes. ALWAYS comply with regulations that
Occupational Safety and Health Administration (OSHA) has
established. ENSURE the generator is installed following the
manufacturer’s instructions.
DANGER
Gaseous fuels such as NG and LPG are highly explosive.
Even the slightest spark can ignite such fuels and cause an
explosion, which could cause burns, fire or explosion resulting
in serious injury, property damage or even death. NO leakage
is permitted.
WARNING
ALWAYS prevent the generator from starting while the covers
are open. The generator may crank and start at any time
without notice. Follow these steps in order:
1. Pull fuse from aXis Controller®panel and secure with tape
to the panel.
2. Disconnect the NEGATIVE, NEG or (-) battery cable first,
and then remove the POSITIVE, POS or (+) battery cable.
To return the generator to service, follow these steps in order:
1. Connect the POSITIVE, POS or (+) battery cable first, and
then connect the NEGATIVE, NEG or (-) battery cable.
2. Remove taped fuse from the panel and reinstall into the
aXis Controller®

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS INSTALLATION
13
L1 L2
L1 L2
N
G
Junction
Box
400A Topology 2x 200A ATS
200A 200A
200A
L1 L2
L1 L2
N
G
Junction
Box
400A
Utility
UTIL
L1 L2
N
G
UTIL
L1 L2
N
G
Primary ATS Secondary ATS
200A Distribution
Panel
200A Distribution
Panel

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS INSTALLATION
14
Primary ATS LEDs
1 ~ 8, 10 & 11 DIP switches in “ON” position.
9 and 12 DIP switches in the “OFF” position.
The LEDs will illuminate after utility power is supplied.
NO
1 2 3 4 5 6 7 8 9 10 11 12
NO
1 2 3 4 5 6 7 8 9 10 11 12
NO
1 2 3 4 5 6 7 8 9 1011 12
Primary
Secondary ATS LEDs
1 ~ 8 DIP switches in the “ON” position.
9, 10 and 12 DIP switches in the “OFF” position.
The LEDs will illuminate after utility power is supplied.
NO
1 2 3 4 5 6 7 8 9 10 11 12
NO
1 2 3 4 5 6 7 8 9 10 11 12
NO
1 2 3 4 5 6 7 8 9 1011 12
Secondary
The LEDs shown pertain only to aXis Controller®Load
Management Modules (LMM).
Both LMM 1 through 4 (LMM1-4) and Gen stop/start (GSTOP/
GSTART) are not illuminated. This is normal and will occur when
DIP #10 is in the OFF (Secondary ATS) position.
NO
1 2 3 4 5 6 7 8 9 10 11 12
NO
1 2 3 4 5 6 7 8 9 1011 12
Secondary
For support, see Settings on the aXis Controller®section.
LMM modules can be attached to either primary or secondary
distribution panel circuits but will be controlled only by primary
ATS. LMM priority is determined by primary ATS and loads will be
controlled as required per the settings input to primary ATS.
Primary ATS kW setting must match HSB rating. Primary ATS will
communicate with secondary ATS to determine total load usage
and determine need to activate LMM modules (if applicable).
When performing LEARN function for loads on LMMs; both
primary and secondary ATS need to be active, but only the primary
ATS is required to LEARN.
HSB is fully controlled by primary ATS. Starting and stopping along
with exercise requirement commands are sent by primary ATS.
Wi-Fi connection should be made at install time to both primary
and secondary ATS units to set day, date, time variables.
Secondary ATS does not need exercise day, date, time set
although it will not affect any operation if set.
HSB battery charge connection (120VAC) can come from either
primary or secondary ATS or primary or secondary distribution
panel. The connection should be fused with no greater than 15A
regardless of source.
Low voltage AC connections can be made from either primary or
secondary ATS.
Secondary ATS low voltage NOT active with DIP switch in the
“OFF” position.

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS INSTALLATION
15
Wi-Fi Setup Method
1. Use a Wi-Fi enabled device (laptop, smart phone, tablet, etc.)
in near proximity to the ATS.
2. Search and connect to network name (SSID) “Champion
####” where #### will match the last four digits of the serial
number that is printed on the control board.
2a. The password for the network is located on a label on the
dead front of the ATS.
PASSWORD
CONTRASEÑA
MOT DE PASSE
12345678
PASSWORD
CONTRASEÑA
MOT DE PASSE
12345678
NOTICE
During the setup your device will disconnect from the internet.
The Champion Wi-Fi is a direct connection between your
device (laptop, smart phone, tablet, etc.) and the ATS, and it
does not connect to the internet. Some Android devices may
show the following screen – Choose “Connect only this time.”
Wi-fi
On
Internet may not be available.
If you want to connect this network without
internet access, you can connect only this
time or you can set your phone to always
connect to it even if internet isn’t available.
You can change this in Settings >
Connections > Wi-fi > ADVANCED >
Switch to mobile data > Network
exceptions
Connect only this time
Allow switch
Stay connected
3. After connecting Wi-Fi, open your device’s web browser. In
the browser address change the address to 192.168.0.90 and
begin search. This will direct your browser to the Champion
aXis Controller®Home Standby Generator Settings page
located on the ATS. If your device’s web browser does not
load the Champion aXis Controller®Home Standby Generator
Settings Page but rather stays connected to the internet, turn
off mobile data on the device (if applicable) and make sure
the device is not connected to any other networks.
192.168.0.90
4. On the Champion aXis Controller®Home Standby Generator
Settings Page, set the date and time. Use either the dropdown
boxes or the “USE THIS DEVICE DATE & TIME” button to set
the time and date.
Generator Date and Time
USE DEVICE DATE & TIME
Date: Choose Month...
Choose Date...
Choose Year...
Time: Choose Hour...
Choose Minute...
Choose AM/PM...
CONFIRM DATE & TIME

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS INSTALLATION
16
5. Confirm and apply the settings before continuing. If you do
not apply immediately, the clock will be later than actual.
Unsaved changes are highlighted.
Home Standby
Generator Settings
Generator Exercise
Every Week
Friday
09:00 AM
Frequency:
Day:
Time:
March 22, 2022
08:40 AM
On
Date
Time
Day Light Saving
Generator Date and Time
EDIT DATE & TIME
(Automated Maintenance Running)
EDIT EXERCISE FREQUENCY
Unsaved Changes
Unsaved Changes
Unsaved Changes
APPLY REVERT
6. Some operating systems will require additional steps to
confirm update, accept all pop-up windows until progress bar
is seen on screen.
Home Standby
Generator Settings
Generator Exercise
Every Week
Friday
09:00 AM
Frequency:
Day:
Time:
March 22, 2022
08:40 AM
On
Date
Time
Day Light Saving
Generator Date and Time
EDIT DATE & TIME
(Automated Maintenance Running)
EDIT EXERCISE FREQUENCY
Unsaved Changes
Unsaved Changes
Unsaved Changes
Are your sure to save the changes?
Cancel OK
Saving...
7. Set the HSB exercise frequency and schedule.
Freq:
Day:
Time:
Choose Mode...
Choose Day...
Choose Hour...
Choose Minute...
Choose AM/PM...
Generator Exercise
(Automated Maintenance Running)
CONFIRM EXERCISE FREQUENCY
8. Confirm and apply the settings before continuing. Unsaved
changes are highlighted.
Every Week
Thursday
01:00 PM
Frequency
Day
Time
Unsaved Changes
Unsaved Changes
Unsaved Changes
Generator Exercise
(Automated Maintenance Running)
EDIT EXERCISE FREQUENCY
APPLY REVERT
Every Week
Thursday
01:00 PM
Frequency
Day
Time
Unsaved Changes
Unsaved Changes
Unsaved Changes
Generator Exercise
(Automated Maintenance Running)
EDIT EXERCISE FREQUENCY
Are your sure to save the changes?
Cancel OK

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS INSTALLATION
17
9. Wireless network settings are not used at this time. The
default values (shown below) should not be adjusted.
Adjustment of this factory settings will require a certified
electrician to correct.
Wireless Network
Internet Service:
Web Page Mode:
Direct Connect
AP Mode
CONFIRM NETWORK SETTINGS
CANCEL SETTINGS
AP Mode IP : 192. 168. 0. 90
Are your sure to save the changes?
Cancel OK
10. The time, date, and exercise information have now been
setup for the aXis ATS and HSB. You can close your browser
and disconnect from the ATS Wi-Fi, or skip to step 2 in the
next section “ATS and HSB STATUS USING WI-FI”.
ATS and HSB Status Using WI-FI
1. Using a WIFI enabled device, connect to the “Champion HSB”
WIFI network following steps 1, 2, and 3 from WIFI Setup
Method.
2. After loading the Home Standby Generator Settings page,
locate and click the icon at the bottom right corner of the
page.
3. You are now viewing the ATS and HSB status page. Items
such as voltage, frequency, current, etc. can all be viewed for
both utility and HSB power. All of the information is live. There
are three tabs located at the top of the page.
ATS, GEN, and LMM. Each tab will display the status for
the Transfer Switch, Home Standby Generator, or Load
Management Module(s) respectively.
4. When finished viewing the status of the ATS, Generator, and
LMM, close your browser and disconnect from the WIFI.
Connecting the Load Management Systems
The following instructions pertain only to aXis Controller®Load
Management Modules (LMM) that use Power Line Carrier (PLC)
communication. If one or more LMM’s are being installed on the
home, install them per the installation instructions included with
the LMM before continuing.
Teaching System
After installation and wiring are complete teach the ATS which
loads are attached by the following procedure. Teaching the
system is only required if 1 or more LMM’s were installed OR if
AC1 OR if AC2 is being used to manage loads.
1. Turn Champion aXis Controller®ATS UTILITY circuit
breaker to the OFF position. Generator will start and run
automatically.
2. Confirm managed loads are all operating.
3. Press and hold the button marked “LEARN” for 8 seconds.
ATS will shutoff managed loads one at a time until all are OFF.
ATS will flash LED’s indicating function in process.
4. After ATS has learned all loads the LMM units will be returned
to normal operation.
5. Installation configuration is now held in memory and will not
be affected by power outage.
6. Return UTILITY circuit breaker to the ON position. ATS will
transfer load back to utility and generator will cool down and
shut off.
7. Repeat this process if LMM units are added or removed from
the system.
NO
1 2 3 4 5 6 7 8 9 10 11 12
0
1
2
3
4
5
6
7
8
9
0
1
2
3
4
5
6
7
8
9

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS INSTALLATION
18
Full System Check
1. Open Utility breaker for full system test, close breaker after
confirming all systems working.
2. After Utility breaker opens engine will start automatically.
3. aXis ATS control panel will reboot on Generator power and
control switching of latching relays.
4. Home is now powered by Generator. If Load Management
modules (LMM) have been installed, they will become active
after 5 minutes.
5. Close Utility breaker
6. System is now fully functional.
7. Replace the dead front by sliding it from the bottom up
into the cabinet; panel should index into the door latch
protrusions. Secure it to the dead front bracket with included
nut and stud.
8. Replace the door and secure with included hardware. It is
recommended to secure the door with a lock.
9. Return to HSB and verify the controller is in “AUTO” mode.
Confirm icons indicate Utility power is active, Utility side relay
is closed, and home is receiving power.
10. Close and lock HSB hoods return keys to customer.
NEMA 1 – This type of enclosed ATS is for indoor installations
only.
NEMA 3R – This type of enclosed ATS is similar to the indoor box,
except that it is a weatherproof enclosure and required for exterior
installations by code. The enclosure only has knockouts on the
bottom side for the enclosure, requires water tight fasteners/
grommets when installed outside per code. This enclosure can
also be used inside.

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS SPECIFICATIONS
19
SPECIFICATIONS
Model 102006 102007 102008 102009 102010
Service Rating Service Entry Rating
Enclosure Style NEMA 3R Outdoor
Maximum Amps 200 150 100
Nominal Volts 120/240
ETL Listed UL STD NO. 1008 CSA STD C22.2 No.
178.1 UL STD NO. 1008 CSA STD C22.2 No. 178.1
Load Management Circuits 4
Weight 43 lbs (19.6 kg)
Height 28 in. (710 mm)
Width 20 in. (507 mm)
Depth 8.3 in. (210 mm)
Technical Specifications
–22kAIC, no short-time current rating.
–Suitable for use in accordance with the National Electrical Code, NFPA 70.
–Suitable for control of motors, electrical discharge lamps, tungsten filament lamps, and electrical heating equipment, where the sum of
the motor full load ampere ratings and the ampere ratings of the other loads does not exceed the ampere rating of the switch, and the
tungsten load does not exceed 30% of the switch rating.
–Continuous load not to exceed 80% of switch rating.
–Line voltage wiring: Cu or AL, min 60°C, min AWG 1 – max AWG 000, torque to 250 in-lb.
–Signal or Com Wiring: Cu only, min AWG 22 – max AWG 12, torque to 28-32 in-oz.
–All connection lugs are rated AL9CU - 90°C rated
NEMA 3R – This type of enclosed ATS is a weatherproof enclosure and required for exterior installations by code. The enclosure has
knockouts on the bottom and side, and requires water tight connections when installed outside per code. This enclosure can also be used
inside.

WHOLE HOUSE AUTOMATIC TRANSFER SWITCH - ALL aXis CONTROLLER®MODELS SPECIFICATIONS
20
102006, 102007, 102008, 102009, 102010 ATS Wiring Diagram
Latching Relay
PIN 2
VE+ VE-
PIN 3
VE-
PIN 1
OPEN CLOSE
Latching Relay
PIN 2
VE+ VE-
PIN 3
VE-
PIN 1
OPEN CLOSE
Utility C.B.
Utility
Generator C.B.
Generator
L2
L1
CT2
CT1
U-L1
U-L2
G-L2
G-L1
U-N
G-N
R
B
Y
Red
Black
L
Yellow
Blue
G
W
Green
White
G/W
Green/White
PART NO:102395.REV 1.0
G
Y
B
R
B
R
L
B
L
R
R
WW
G/W
L
B
R
W
Y
G
R
B
R
B
B
R
B
Neutral Bar
Ground Bar
G-GND
CHARGER POWER
600Vac KTK-10 Fuse
UTILITY SENSE
600Vac KTK-10 Fuse
CHARGER-L
CHARGER-N
R
B
G/W
ATS controller Board
J5
L1 N L2
J1
G-V G-U N U-S U-R
J8
J12
AC2-C2(Com)
AC2-C1
AC1-C2
AC1-C1
J3
CT1+
CT1-
J11
U-Close
U-Com
U-Open
J10
G-Close
G-Com
G-Open
J7
G
D-
D+
+24V
2-Wire
J4
CT2+
CT2-
L
W
G/W
G/Y
GND
G/Y
Green/Yellow