CHAMPIONS AG070 User manual

Shenzhen Champions Technology Co.,Ltd specification
Wireless remote control
AG070
Specification
•Transmitting power:5dBm
•Modulation mode:ASK/OOK
•Standby current: ≤0.1uA
•emission current :≤10mA
Product description:
4 Key wireless remote control AG070 (learning code) and (rolling code) is our
company in July 2011 developed a novel design, stable performance of small power
wireless remote control, internal encryption coding chip, chip built-in RC
shock very few peripheral parts, high frequency part with the steady frequency
transmission efficiency is high, can be used for battery car remote lock and
all kinds of short distance wireless remote control products.
Remote Control Specifications:
●Product model: AG070 (standard shipping key symbol ABCD, other symbol keys need
to be customized)
●Operating voltage: 12V / 27A alkaline battery
●Transmit current:＜10mA
●Standby current:≤0.1uA
●Transmitting power:≤5dBm
●Transmit frequency: 433.9185MHz
●Transmitting:ASK/OOK
●Encoder mode :EV1527 ending format (learning code / 301 rolling code)
●Key code value: A key (D0=1000) B key (D1=0100) C key (D2=0010) D key (D3=0001)
●Size specification: 54 * 30 * 14mm (excluding key chain)
●Product weight: 26 g (including key chain)
●Case material: PC (metallic light + matte)

Shenzhen Champions Technology Co.,Ltd specification
●Remote control distance: 30-50 m reference distance (related to the environment and
supporting reception sensitivity)
Scope of application:
Battery car remote control, rolling shutter door remote control, access control remote
control, toy remote control, curtain remote control, all kinds of lamps and all kinds of
products that need wireless remote control to use.
Code description: (Code width 1.2 data)
AG070 (learning code) data string
AG070 (rolling code) data string
Address bit: 20*1.208=24.16ms data bit: 4*1.208=4.832ms
synchronization bit: 8*1.208=9.664ms
The AG070 remote control chip is EV1527 (learning code), and a chip burns a unique
address code.
AG070 remote control chip is 301 (rolling code), rolling code as above.
Address code and data code code width definition:
The clock frequency
corresponding to the code width is:
OSC CLOCK=102.6KHz(1.2ms)

Shenzhen Champions Technology Co.,Ltd specification
The RF112B chip has a standard shipment code width of 1.2ms and is compatible with
most receiving decoding programs.
Supporting receiving module: J06B (learning code) J06C (learning code) J06T (learning
code is ultra-low power consumption)
AG070 Remote Control and Receiving Supporting Instructions:
AG070 remote control chip is a EV1527 coding format, receiving needs to be
single-chip decoding, as long as the reception is learning decoding program can be
matched.Each remote control must be and receive the right code for the remote control.The
decoder must be compatible with a 1.2MS code width
4-Key Wireless remote control circuit diagram
The AG070 circuit diagram is the same, the key code value is the same, but the chip
burning address is not the same AG070 remote control chip packaging process is
different, AG070 frequency accuracy is high ratio, good consistency and long distance.
keycode value

Shenzhen Champions Technology Co.,Ltd specification
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receivingantenna.
•Increase the separation between the equipment andreceiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority
to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
RF Exposure Information
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure
condition without restriction.