Channel Plus SVD-8 User manual

Residential Gateway model 8157
by
TM
S-Video Distribution Module
Model SVD-8
Designed for
ChannelPlus and OpenHouse
structured wire grid systems.
multiplexmultiplex
®
®
technology, inc.technology, inc.
3001 Enterprise Street, Brea, CA 92821-6213, U.S.A.
714-996-4100 800-999-5225 Fax [phone] www.channelplus.com
• • •
TM
IR OutputPower
Transmitter
Input Receiver Outputs
S-Video Distribution Module SVD-8
54321 6 7 8
Differential Drive Engine
800
1000
600400
0
200 800
1000
600400
0
200 800
1000
600400
0
200 800
1000
600400
0
200 800
1000
600400
0
200 800
1000
600400
0
200 800
1000
600400
0
200 800
1000
600400
0
200
54321678

Example
Attach the IR emitter
directly over the IR sensor.
IR from any of eight locations
will control the DVD player. IR
is available at either the SVC-10
transmitter or any of the three IR
outputs of the SVD-8 module.
LEFT
300mA
15VDC
POWER IR REPEATERS
800
1000
600
400
0
200
CAT-5
VIDEO OUT
DIGITAL OUT
AUDIO OUT
VIDEO IN
DIGITAL IN
AUDIO IN
RIGHTCOAX OPTICAL
LENGTH
ADJUST
(in feet)
VIDEO S-VIDEO
PCM/AC3/DTS
800
1000
600
400
0
200
Set LENGTH ADJUST to 600
Connect a local monitor here
Connect a local receiver here
DVD
600 feet CAT
-5
350-103 power supply 2171
Digital
audio
s-video
TM
IROutput
Power
Transmitter
InputReceiverOutputs
S-VideoDistributionModuleSVD-8
5
4
3
2
1678
DifferentialDriveEngine
800
1000
600
400
0
200800
1000
600
400
0
200800
1000
600
400
0
200800
1000
600
400
0
200800
1000
600
400
0
200800
1000
600
400
0
200800
1000
600
400
0
200800
1000
600
400
0
200
5
4
3
2
1678
SVD-8
SVC-10 Transmitter
800
1000
600
400
0
200
Set LENGTH ADJUST to 300
800
1000
600
400
0
200
Set LENGTH ADJUST to 1000
350-106 power
supply (included)
Connect up to six more outputs. Use
distance to the receiver to set length
adjust dial (see ouputs 7 & 8 for example).
Separate and slide labels
into extrusion, or flip the
label over and write on
the blank surface.
Front
Master
Suite 4
Rear
Master
Suite 4
Typical Installation
Remove two end
screws and replace
with alternate ears
for surface mounting.
2
POWER LEFT
AUDIO
RIGHT DIGITAL
AUDIO COAX VIDEO S-VIDEO CAT-5 IR INPUT
POWER LEFT
AUDIO
RIGHT DIGITAL
AUDIO COAX VIDEO S-VIDEO CAT-5 IR INPUT
Digital
Surround Sound
Processor
Digital
Surround Sound
Processor
TV
TV
2132
2132
350-103 power supply
300 feet CAT-5
1000 feet CAT-5
SVC-10R
SVC-10R
(1) SVD-8 S-Video Distribution Module
(1) 15VDC power supply
(2) Flat surface mounting ears
(44) Location Labels
SVD-8 Contents Wiring Modular Plug
(T568A)
Wire order:
White/Green
Green
White/Orange
Blue
White/Blue
Orange
White/Brown
Brown
Do not untwist
more than 0.5"
350-103 power supply
3

Multiplex Technology, Inc. warrants this product to be free from defects in
materials and workmanship for a period of one year from the date of
purchase or MTI will repair, or at its option, replace the defective product. To
obtain warranty service, call MTI for a return material authorization (RMA)
number and return the product prepaid to Multiplex Technology, Inc., 3001
Enterprise Street, Brea, CA 92821, Attention: Customer Service. Please put
the RMA number on the outside of the carton.
Any implied warranty arising from the sale of the product including implied
warranties of merchantability and fitness for purpose are limited to the
warranty stated above. MTI shall not be responsible for losses or damages
or expenses, whether direct, consequential or incidental arising from the
use of or the inability to use this product. Some states do not allow limitations
on how long the implied warranty lasts or the exclusion or limitation or
incidental or consequential damages, so the above limitations and
exclusions may not apply to you. This warranty gives you specific legal
rights, and you may have other rights which may vary from state to state.
Warranty
600-243 REV. A Multiplex Technology, Inc., Brea, CA 92821-6213
Troubleshooting:
Problem: No video or audio on any receiver.
Try this: 1) Check CAT-5 connection from SVC-10 transmitter to the SVD-8.
2) Check power on SVD-8 and SVC-10 transmitter.
3) Check video/audio source power and connections to transmitter.
Problem: No video or audio on only one receiver.
Try this: 1) Check CAT-5 connection from SVD-8 to the SVC-10R receiver.
2) Check power on SVC-10R receiver.
3) Check for proper connections from the SVC-10R receiver to the TV.
Problem: Poor video quality at one location.
Try this: 1) Check CAT-5 connection from SVD-8 to the SVC-10R receiver.
2) Check proper dial setting on the SVD-8 for that location.
Troubleshooting hints:
- Problems that appear at all locations are likely due to connection errors
between the SVC-10 transmitter and the SVD-8.
- Problems that appear at only one location are likely due to connection errors
between the SVD-8 and the SVC-10R receiver.
- Proper termination is key - verify the correct color codes at each end of the
CAT-5 cable.