Channel Vision B-204 User manual

B-204
IP Camera Over Coax Converter Kit
2
1
500-303 rev B
www.channelvision.com
234 Fischer Avenue, Costa Mesa, California 92626 USA
[phone] [phone] [phone] fax
email: [email protected]
1
Channel Vision Technology will repair or replace any defect in material or
workmanship which occurs during normal use of this product with new or
rebuilt parts, free of charge in the USA, for one year from the date of
original purchase. This is a no hassle warranty with no mail in warranty
card needed. This warranty does not cover damages in shipment, failures
caused by other products not supplied by Channel Vision Technology, or
failures due to accident, misuse, abuse, or alteration of the equipment. This
warranty is extended only to the original purchaser when purchased
through an authorized reseller. A purchase receipt, invoice, or other proof
of original purchase date will be required before warranty repairs are
provided. Channel Vision products are not intended for use in medical,
lifesaving, life sustaining or critical environment applications. Channel
Vision customers using or selling Channel Vision products for use in such
applications do so at their own risk and agree to fully indemnify Channel
Vision for any damages resulting from such improper use or sale.
Mail in service can be obtained during the warranty period by calling (800)
840-0288 toll free. A Return Authorization number must be obtained in
advance and can be marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights
(which vary from state to state). If a problem with this product develops
during or after the warranty period, please contact Channel Vision
Technology, your dealer or any factory-authorized service center.
B-204
IP Camera Over Coax Converter Kit
2
1
500-303 rev B
www.channelvision.com
234 Fischer Avenue, Costa Mesa, California 92626 USA
[phone] [phone] [phone] fax
email: [email protected]
1
Channel Vision Technology will repair or replace any defect in material or
workmanship which occurs during normal use of this product with new or
rebuilt parts, free of charge in the USA, for one year from the date of
original purchase. This is a no hassle warranty with no mail in warranty
card needed. This warranty does not cover damages in shipment, failures
caused by other products not supplied by Channel Vision Technology, or
failures due to accident, misuse, abuse, or alteration of the equipment. This
warranty is extended only to the original purchaser when purchased
through an authorized reseller. A purchase receipt, invoice, or other proof
of original purchase date will be required before warranty repairs are
provided. Channel Vision products are not intended for use in medical,
lifesaving, life sustaining or critical environment applications. Channel
Vision customers using or selling Channel Vision products for use in such
applications do so at their own risk and agree to fully indemnify Channel
Vision for any damages resulting from such improper use or sale.
Mail in service can be obtained during the warranty period by calling (800)
840-0288 toll free. A Return Authorization number must be obtained in
advance and can be marked on the outside of the shipping carton.
This warranty gives you specific legal rights and you may have other rights
(which vary from state to state). If a problem with this product develops
during or after the warranty period, please contact Channel Vision
Technology, your dealer or any factory-authorized service center.

•
•
3
Installation:
Connect video signal to the BNC connector of the B-204
Attach aT568B standard CAT5 cable to the RJ-45
connector on each balun
Installation Diagram
Specifications:
Video In/Out:
Transmission distance:
RJ-45 Connector standard:
Coax Cable:
Dimensions:
(Without connectors)
Data Rate:
BNC male connector
Max. 300 ft.
T568B
RG-59/RG-6
10Mbps
Wire type: UTP Category5,5e
W 38mmxD28mmxH15mm
*Specifications subject to change without notice.
Up to 300 ft.
of
RG cable
Any standard network
router or switch
6521 IP Camera
2
Model B-204
Features:
BNC connector
for standard
75-ohm video cable
RJ-45 connector
for Ethernet
(T568B)
The B-204 IP Camera Over Coax Converter Kit is a perfect
solution for updating analog based security cameras to IP based
cameras by using the original coax cabling infrastructure.
The B-204 enables the transmission of an IP camera over 300’
of RG-59/6 video grade coax cable and supports up to 10Mbps
bandwidth. The B-204 is a passive device with no additional
power requirements. By using the existing coax and power
cables, the B-204 can create a more scalable, manageable
solution without the need to run new wire. The B-204 can
connect to any standard network router or switch and supports
IP cameras, including Channel Vision’s 2 megapixel HD dome
(6521), bullet (6522), and flush mount (6524) IP cameras, as well
as its 1.3 megapixel indoor dome (6530).
• Sends video over 300’ of coax cable
• Compatible with Category 5, 5e and 6 wiring
• Small size allows installation in crowded spaces
• Kit contains (1) transmitter and (1) receiver
•
•
3
Installation:
Connect video signal to the BNC connector of the B-204
Attach aT568B standard CAT5 cable to the RJ-45
connector on each balun
Installation Diagram
Specifications:
Video In/Out:
Transmission distance:
RJ-45 Connector standard:
Coax Cable:
Dimensions:
(Without connectors)
Data Rate:
BNC male connector
Max. 300 ft.
T568B
RG-59/RG-6
10Mbps
Wire type: UTP Category5,5e
W 38mmxD28mmxH15mm
*Specifications subject to change without notice.
Up to 300 ft.
of
RG cable
Any standard network
router or switch
6521 IP Camera
2
Model B-204
Features:
BNC connector
for standard
75-ohm video cable
RJ-45 connector
for Ethernet
(T568B)
The B-204 IP Camera Over Coax Converter Kit is a perfect
solution for updating analog based security cameras to IP based
cameras by using the original coax cabling infrastructure.
The B-204 enables the transmission of an IP camera over 300’
of RG-59/6 video grade coax cable and supports up to 10Mbps
bandwidth. The B-204 is a passive device with no additional
power requirements. By using the existing coax and power
cables, the B-204 can create a more scalable, manageable
solution without the need to run new wire. The B-204 can
connect to any standard network router or switch and supports
IP cameras, including Channel Vision’s 2 megapixel HD dome
(6521), bullet (6522), and flush mount (6524) IP cameras, as well
as its 1.3 megapixel indoor dome (6530).
• Sends video over 300’ of coax cable
• Compatible with Category 5, 5e and 6 wiring
• Small size allows installation in crowded spaces
• Kit contains (1) transmitter and (1) receiver