Char-Broil EDGE Use and care manual

42805399 • 03/14/22
CHAR-BROIL EDGETM
ELECTRIC GRILL
MODEL 22652143
PART REPLACEMENTGUIDE
NOTE: Some grill parts shown in the assembly steps may differ slightly
in appearance from those on your particular grill model. However, the
method of assembly remains the same.
Fuse .............................................2
Controller ....................................... 3-4
Top Fascia Panel / Temperature Probe / Control Panel .... 5-8
Heating Element / Reflector Plate Assembly ........... 9-12
Firebox ....................................... 13-17
Power Cord.................................... 18-21
TABLE OF CONTENTS
CAUTION
Some parts may contain sharp edges. Wear protective
gloves if necessary.

PAGE 2
1Remove / replace FUSE.
Remove / replace FUSE.
Each step shows removal and replacement of parts. Follow the steps in order to remove parts, then reverse the
steps to replace all parts.
1ST
2ND
FUSE

PAGE 3
1
2
Unplug / replug CABLES.
Remove / replace CONTROLLER.
Remove / replace CONTROLLER

PAGE 4
3
4Remove / replace CONTROL KNOB.
Remove / replace CONTROLLER.
CONTROLLER
CONTROLLER
CONTROL KNOB

PAGE 5
1
2
Remove / replace GREASE PAN.
Remove / replace COOKING GRATE, WARMING PLATE and GREASE BAFFLE.
Disconnect / connect the wires on CONTROLLER and POWER BOX.
Remove / replace TOP FASCIA PANEL , TEMPERATURE PROBE and CONTROL PANEL
GREASE PAN
WARMING PLATE
COOKING GRATE
GREASE BAFFLE
!
CAUTION
Failure to install grease pan will cause hot grease to drip from
bottom of grill with risk of fire or property damage.
!
POWER BOX
CONTROLLER
1ST
2ND

PAGE 6
3
4
Remove / replace GRILL HEAD.
Remove / replace TOP FASCIA PANEL.
TOP FASCIA PANEL

PAGE 7
TOP FASCIA PANEL
5
6
Remove / replace TOP FASCIA PANEL.
NOTE: Route the wires through the holes as shown while replacing TOP FASCIA PANEL.
Remove / replace TEMPERATURE PROBE.
TEMPERATURE PROBE
1ST
2ND
Care should be taken when removing the wire tie from the
Temperature Probe and Heating Element wire to prevent
damage.

PAGE 8
CONTROL PANEL
7
8
Remove / replace CONTROL PANEL.
Remove / replace CONTROL PANEL and CONTROLLER.
CONTROL PANEL
CONTROLLER
1ST
2ND

PAGE 9
1
2
Remove / replace GREASE PAN.
Remove / replace COOKING GRATE, WARMING PLATE and GREASE BAFFLE.
Remove / replace HEATING ELEMENT and REFLECTOR PLATE ASSEMBLY
GREASE PAN
WARMING PLATE
COOKING GRATE
GREASE BAFFLE
!
CAUTION
Failure to install grease pan will cause hot grease to drip from
bottom of grill with risk of fire or property damage.
!

PAGE 10
3
4
Remove / replace GRILL HEAD.
Remove / replace TOP FASCIA PANEL.
TOP FASCIA PANEL

PAGE 11
TOP FASCIA PANEL
5
6
Remove / replace TOP FASCIA PANEL.
NOTE: Route the wires through the holes as shown while replacing TOP FASCIA PANEL.
Remove / replace TEMPERATURE PROBE.
TEMPERATURE PROBE
1ST
2ND
Care should be taken when removing the wire tie from the
Temperature Probe and Heating Element wire to prevent
damage.

PAGE 12
7
8
Remove / replace HEATING ELEMENT and REFLECTOR ASSEMBLY.
Remove / replace HEATING ELEMENT and REFLECTOR ASSEMBLY.
REFLECTOR ASSEMBLY
HEATING ELEMENT
HEATING ELEMENT
1ST

PAGE 13
1
2
Remove / replace GREASE PAN.
Remove / replace FIREBOX
GREASE PAN
!
CAUTION
Failure to install grease pan will cause hot grease to drip from
bottom of grill with risk of fire or property damage.
!
Remove / replace COOKING GRATE, WARMING PLATE and GREASE BAFFLE.
Disconnect / connect the wires on CONTROLLER and POWER BOX.
WARMING PLATE
COOKING GRATE
GREASE BAFFLE
POWER BOX
CONTROLLER
1ST
2ND

PAGE 14
3
4
Remove / replace GRILL HEAD.
Remove / replace TOP FASCIA PANEL.
TOP FASCIA PANEL

PAGE 15
TOP FASCIA PANEL
5
6
Remove / replace TOP FASCIA PANEL.
NOTE: Route the wires through the holes as shown while replacing TOP FASCIA PANEL.
Remove / replace CONTROL PANEL ASSEMBLY.
CONTROL PANEL ASSEMBLY
1ST
1ST
2ND
2ND

PAGE 16
7
8
Remove / replace GREASE PAN BRACKETS.
Remove / replace TOP LID ASSEMBLY.
TOP LID ASSEMBLY
GREASE PAN BRACKET

PAGE 17
9
10
Remove / replace TEMPERATURE PROBE.
Remove / replace HEATING ELEMENT ASSEMBLY and FIREBOX.
TEMPERATURE PROBE
FIREBOX
HEATING ELEMENT
ASSEMBLY
1ST
Care should be taken when removing the wire tie from the
Temperature Probe and Heating Element wire to prevent
damage.

PAGE 18
1
2
Disconnect / connect the wires on CONTROLLER and POWER BOX.
Remove / replace POWER BOX.
Remove / replace Power Cord
POWER BOX
CONTROLLER
POWER BOX

PAGE 19
3
4
Remove / replace POWER BOX COVER.
Remove / replace CONNECTOR COVER.
CONNECTOR COVER
POWER BOX COVER

PAGE 20
5
6
Loosen / Tighten the screw assemblies to remove / secure the wires.
Pull out / Route the ground wire as shown.
Remove / Secure the NUT for power cord to remove / replace POWER CORD.
Loosen / Tighten the screws
GROUND WIRE (Green)
NUT
Black Wire
Bottom White Wire