Char-Broil SILVER SMOKER 3201560 User manual

42802119 (01-09-04)
THIS UNIT IS HEAVY. DO NOT assemble without helper.
Some parts may contain sharp edges - especially as noted in
manual. Wear protective gloves if necessary.
Read and follow all safety statements, warning, assembly
instructions and use & care directions before attempting to
assemble and cook.
Tools needed for
assembly:
2 Adjustable Wrenches
7/16” Open-End Wrench
Flat Screwdriver
Hammer
CARBON MONOXIDE HAZARD
Burning charcoal inside can kill
you. It gives off carbon monoxide,
which has no odor. NEVER burn
charcoal inside homes, vehicles
or tents.
0420110103201560 • 04201113
Smoker, BBQ and Grill

STOP!
Missing a part?
No need to go back to the store!
The store where you made your purchase
does not stock parts for this item. If you
need parts, whether they are missing or
damaged, call the Customer Service toll
free Help Line.
Call us and we will gladly ship
the part you need
FREE OF CHARGE.
Call Our Help Line
PARTS LIST
ITEM DESCRIPTION
55700193 SMOKER CHAMBER KIT
55700194 FIREBOX KIT
55700195 WOOD SHELF KIT
55700442 AXLE KIT
55700443 WHEEL KIT
55700198 LEG BRACE KIT
55700199 SMOKESTACK KIT
55700200 SHORT LEG KIT
55700201 LONG LEG KIT
55700202 SHELF BRACKET KIT
55700203 COVER PLATE KIT
55700204 DOOR LATCH KIT
55700205 LOGO PLATE KIT
55700206 8” WOOD HANDLE KIT
55700192 BUTTERFLY DAMPER KIT
42000010 HARDWARE BAG
10000074 LEG CAPS
40009916 LARGE PORCELAIN GRATE SET
40009925 SMALL PORCELAIN GRATE
40022811 FIRE GRATE SET (3)
46030090 WOOD STORAGE RACK
44830150 GREASE CLIP
40003010 OPTIONAL TEMPERATURE GAUGE
42802119 ASSEMBLY INSTRUCTIONS

Attach leg braces to the outside of one leg assembly using #10-24x1¾” screws and #10-24 flange nuts. Make sure slotted
(oval) hole is toward bottom of leg. Do not fully tighten screws until Step 8 is complete.
2
1FIRST, GET A HELPER! This unit is heavy and requires a second person for lifting and moving. NEXT, pick a suitable location to
work. Open the carton and slit the corners so that the carton lays flat. This will give you a protective work surface during assembly.
TO BEGIN ASSEMBLY, build two leg assemblies by sliding the long leg sections into the short leg sections.
Long leg section
Leg brace
Short leg section
Slotted
hole
Leg brace

3Lay the leg assembly on its side with legs braces pointing upward. Insert the wood rack hooks into leg holes and swing rack
upward, parallel to leg braces.
4With the aid of a helper, place leg holes of remaining leg assembly over wood rack hooks and rotate leg assembly until it meets
the leg braces. Make sure both short legs are at one end of the rack and both long legs at the other end. Attach to leg braces
using #10-24x1¾” screws and #10-24 flange nuts. Do not fully tighten screws until Step 8 is complete.
Wood rack
Short leg
Short leg
Long leg
Long leg

6
5Insert a cotter pin into the hole at one end of the axle and bend the ends of the pin back so that it cannot be removed. Slide a
wheel onto the axle. Slide the axle through the holes at the ends of the short legs. Slide remaining wheel onto axle and secure
with remaining cotter pin.
Axle
NOTE: Smoker chamber door not pictured
for clarity.
Stand the leg assembly on end, wheels
down. Stand the smoker chamber on its
solid end, open end up. Place leg assembly
against chamber, aligning holes in legs with
holes in chamber. Attach legs to chamber
using four 1/4-20x2” screws and 1/4-20
flange nuts. Insert screws from outside,
flange nuts inside chamber.
FULLY TIGHTEN ALL SCREWS AND
NUTS AT THIS TIME.
Smoker chamber
Cotter pin
Cotter pin
Wheels down
Open end up

7
8
Smokestack
NOTE: Smoker chamber door not pictured for clarity.
From inside the smoker chamber, slide the smokestack through the large hole. Align the two holes in the smokestack plate with
the holes in the chamber and secure with two 1/4-20x3/4” hex-head bolts outside the chamber and 1/4-20 flange nuts inside.
NOTE: Smoker chamber and firebox doors not pictured for clarity.
TM TM
Diamond Fire Plate Installation - For models without Diamond Fire ignitor accessory,
part number 22504850.
TM
For models that feature the Diamond Fire ignitor accessory, supplemental
instructions are included with ignitor.
First, locate the cover plate in the hardware box. At the bottom right end of the
TM
firebox there is an opening for the Diamond Fire ignitor accessory. Install the
cover plate over the opening using two #8-32x1/2” screws and #8-32 lock nuts.
Second, align the hole pattern on the firebox with the pattern on the
smoker chamber. The firebox should be slightly offset from the smoker
chamber. Attach using six 1/4-20x3/4” hex-head bolts and flat washer
inside firebox and 1/4-20 flange nuts inside smoker chamber.
Firebox
Smoker
chamber
Smokestack plate
Cover plate
Firebox

9
10
Attach wood handle to smoker chamber door using two 1/4-20x3” screws, flat washers, handle spacers and 1/4-20 flange
nuts, as shown below. Repeat to attach handle to firebox door.
NOTE: Smoker chamber door not pictured for clarity.
Install grate support screws in the four rear holes and two
front-center holes in the smoker chamber. Use six #10-24x1”
screws and #10 flange nuts.
Smoker chamber
door
Handle spacer
Handle

NOTE: Smoker chamber door not pictured for clarity.
Attach shelf brackets to outer holes on front of smoker chamber
using two 1/4-20x1¼” hex-head bolts and 1/4-20 flange nuts.
DO NOT FULLY TIGHTEN.
12
11
Shelf bracket
NOTE: Smoker chamber door not pictured for clarity.
First, attach shelf slats to the two outer holes in shelf brackets using
two #10-24x1” screws and #10-24 flange nuts per slat. DO NOT
FULLY TIGHTEN SCREWS. Second, fully tighten hex-head bolts on
shelf brackets (installed in previous step). Third, attach remaining
shelf slat to brackets with two #10-24x1” screws and #10-24 flange
nuts. FULLY TIGHTEN ALL SHELF SLAT SCREWS.
Attach two outer
shelf slats. Do not
tighten.
1st
Tighten bracket bolts.
2nd
Attach inner slat.
Fully tighten all
slat screws.
3rd

14
13 If you have purchased the optional 3” Temperature Gauge,
part number 40003010, remove the attached nut, insert
gauge stem into large hole in cooking chamber door and
attach nut to gauge on inside of door. DO NOT
OVERTIGHTEN NUT. Make sure text and graphics are
aligned for easy viewing.
If you do not have a temperature gauge, install the chrome
hole plug (provided) into temperature gauge hole in cooking
chamber door.
If you would like to purchase the optional 3” Temperature
Gauge, part number 40003010, call 1-800-232-3398.
Hole plug
Hang grease clip from holes on bottom right side of smoker chamber. A 12 oz. soup or vegetable can will fit nicely into clip to
collect grease.
Grease
clip

16
15 If logo plate is not already installed, insert logo plate pins into two holes in lower right corner of smoker chamber door. Press
logo plate clips onto pins until snug against inside of door.
Logo plate
NOTE: Smoker chamber door not pictured for clarity.
If you wish to grill in the smoker chamber, place two of the three
wire fire grates into bottom of smoker chamber. Place two large
porcelain cooking grates into chamber, resting them on the grate
support screws.
Large porcelain
cooking grate (2)
Logo plate clip
Wire fire grate (2)