Charnwood FIREBALL User manual

CHARNWOOD FIREBALL
The Charnwood Fire Ball is a self-assembly outdoor
fire pit kit British made on the Isle of Wight. A modern,
sculptural piece for the garden with a rustic finish.
This iconic piece is cut from mild steel and supplied as a flat pack
kit making the perfect present for someone who enjoys a small project.
The satisfaction of building this product is all part of the experience. All that
is required is an hour of your time, sturdy gloves, a pair of pliers and a
hammer.

90°
140°
Prepare each flat dome segment part on a flat surface,
ensure the part number engraving is always facing down.
All long joining tabs should be folded at approx. 140 ° and
short tabs at 90°. You will need a small pair of pliers to
aid you in folding the joining tabs
The ball is made up of 6
segments marked as:
TH160/01 qty x 1
TH160/02 qty x 1
TH160/03 qty x 2
TH160/04 qty x 1
TH160/05 qty x 1
TH165 is a tool that can be
used to check the precision
of the angles of the folded
tabs if required.
PREPARATIONPREPARATION
90°
140°
115°

Lay the prepared segment on a flat surface
3 folds as illustrated by dashed lines
2 folds as illustrated by dashed lines.
Bend the tabs fully over and lock
into position. Use a small hammer to
flatten the tabs into place.
1
2
3
4Completed segment. Repeat steps
1-3 for all remaining dome pieces.

TH160/01
TH160/03
TH160/04
TH160/02
12
3
4
5
6
Take part TH160/01 and TH160/02 and attach
them together using the six tabs as shown in the
illustration. It is best to align the first tab and then
work down. This will form the
base of the ball.
To secure the tabs, bend the
tabs fully over and lock into
position. Use a small hammer
to flatten the tabs into place.
Note the orientation of the logo on
the front of the base.
Connect TH160/03 in the same way
as illustrated and secure the six tabs.
Connect TH160/04 in the same way as
illustrated and secure the six tabs.
BALL ASSEMBLYBALL ASSEMBLY
5
6
7

TH160/05
Connect TH160/03 in the same way as
illustrated and secure the tabs.
To complete the ball, take part TH160/05 and assemble in position shown
inside the dome. Some adjustment of the tabs may be necessary to fit this part.
Secure the tabs once in position.
TH160/03
8
9

Prepare the five base parts on a flat surface, ensure the
part number engraving is always facing down. All long side
joining tabs should be folded at aprox 115° and side short
tabs at 90°. You will need a small pair of pliers to aid
you in folding the joining tabs
Assemble the five stand parts as shown and secure the
tabs by bending the tabs fully over and locking into
position. Use a small hammer to flatten the tabs into
place.
90°
115°
DO NOT FOLD
THE TOP TABS
Note orientation of Charnwood logo text on front piece
BASE ASSEMBLYBASE ASSEMBLY
10
11

Line up the five upright tabs on the top of the
base with the five slots underneath the ball
and assemble. Some adjustment to the tabs
may be necessary. Once aligned, secure by
folding the tabs fully over inside the ball.
Completed fire ball assembly. The
wood / ash level should not reach
higher than the three air holes.
Slots underneath the ball
12
13

USE AND SAFETY
The Fireball will get hot in use and is intended for
outside use only.
It must be placed on a non-combustible surface and away from
combustible objects.
This product is only designed to burn wood and the ash level should not
reach higher than the three air holes.
The Fireball is cut from mild steel and is 100% recyclable.
Due to the nature of steel the Fireball will oxidise over time and the
look of the product will change. This is all part of the design and
character of the product.
Please burn responsibly

ENJOY YOUR
#charnwoodfireball