Charnwood TH160-01 User manual

FIRE BALLFIRE BALL

FIREBALL USE / SAFETY
The product must be placed on a
non-combustible surface and away
from combustible objects.
This product is only designed to burn wood.
The wood / ash level should not reach higher than the
three air holes.
The product is made from mild steel and is 100%
recyclable. Due to the nature of steel, it will oxidise
over time and the look of the product will change.
The product is intended for outside use only.
This product gets hot in use.

PREPARATION
Before assembly check that you have the 11 flat parts as illustrated below.
It is recommended that you have a flat non-marking surface to work on when assembling the
firepit. You will need a small pair of pliers to aid you in folding the joining tabs and a small hammer
may also be useful when flattening the tabs. Wearing a pair of work gloves is recommended to
avoid injury.
ASSEMBLING THE BALL
1. Select the 5 parts as shown below.
Although each of the above parts have the same outline, they do not all have the same cut
features. It is therefore very important that these parts are folded correctly to allow correct
assembly of the product.
2. Take part TH160~01 and fold all the narrow tabs up at an angle of 90° and all the wide tabs
up at an angle of 140°. Please note that these angles are only approximate.
3. Fold up in two steps as shown below and lock together in two places using the tabs. Please
note the orientation of the logo.
TH160~01
TH160~06 TH160~06 TH160~06 TH160~06 TH160~07 TH160~05
TH160~03TH160~02 TH160~04 TH160~03
TH160~01 TH160~02 TH160~03 TH160~04 TH160~03
Note the different cut features
90° 140°
Note the orientation of the logo
Step 1 (3 folds) Step 2 (2 folds)
Bend the tabs fully over to
lock in position
Completed segment:
5
4

5. Take Part TH160~03 (There are two of this part and both should be folded the same). Fold
up and lock together in the same way as part TH160~01.
4. Take part TH160~02. Fold up and lock together in the same way as part TH160~01.
Note position of cut outs
Note position of cut out
76

7. Take part TH160~01 and TH160~02 and attach them together as shown in the illustration
using the tabs.
8.
6. Take Part TH160~04. Fold up and lock together in the same way as part TH160~01.
Note position of cut out
Note orientation of logo
Note position of cut outs
Bend small tabs fully over
to lock in position
98

9. To complete the dome, take part TH160~05 and assemble in position shown. Some adjustment
of the tabs may be necessary to fit this part.
8. Assemble the remaining three parts in the same way as illustrated in the previous step until
the dome is formed.
Bend small tabs fully over
to lock in position
Pre-bend tabs slightly
before fitting
1110

ASSEMBLING THE STAND
1. Select the 5 parts as shown below.
2. Take part TH160~07 and bend small side tabs up at approximately 90° and large side tabs
up at approximately 120°. Make sure that the ‘Charnwood’ name cut is orientated as shown in
the images below.
3. Fold up the tabs on parts TH160~06 (four parts). Make sure these are folded in the same way
as part TH160~07 so that they will fit together correctly.
4. Assemble the five stand parts as shown. Lock in place by folding small tabs fully over.
BALL AND STAND ASSEMBLY
1. Line up the five tabs on the top of the stand with the five slots in base of the ball and assemble.
Fold the tabs fully over inside the ball once the ball has been aligned with the top of the stand.
TH160~06 TH160~06 TH160~06 TH160~06TH160~07
X4
Slots in the base of the dome
1312