EAST OAK GFT22001 User manual

BRAZI Fire Pit Table
60000 BTU
Owner’s Manual
MODEL:
GFT22001 | GFT22002 | GFT22003
GFT22004 | GFT22005 | GFT22006
GFT22007 | GFT22008 | GFT22009

1EASTOAK.COM FIRE PIT TABLE
Claim your 3-year warranty
at eastoak.com/warranty
Questions? Comments?
Reach out to us to for expert support!
suppor[email protected]
eastoak.com
1-833-EAST-OAK (USA)
(1-833-327-8625)
eastoak.com
Follow eastoakliving on

2[email protected]1-833-327-8625
IMPORTANT CAUTION
CAUTION: PLEASE READ ENTIRETY OF MANUAL PRIOR TO ASSEMBLY AND
OPERATION.
Verify all parts and components are present. Check all pieces for any damage
before assembly. If any parts are damaged or missing, contact customer
service at suppor[email protected].
• Some pieces contain sharp edges, which may cause injury or property
damage. To prevent personal injury or damage, please wear protective
gloves during assembly.
• Set power tools setting to the lowest speed possible to prevent any damage.
DANGER
• This product can produce an odorless carbon monoxide, which if used in an
enclosed space may result in death.
• Using it in an enclosed space can kill you.
• Do not use this appliance in an enclosed space, such as a tent, camper, car,
or inside your home.
If you smell gas:
• Shut off gas supply to the appliance completely.
• Extinguish any open ames immediately.
• If the odor persists, leave the area immediately.
Once you are safe, call your gas supplier or dial 911 to call the re department.
Failure to follow these directions and act quickly may result in an re or explosion
and result in property, damage, injury, or death.
IMPORTANT INFORMATION

3EASTOAK.COM FIRE PIT TABLE
WARNING
• This product is for outdoor use only.
• All installation, service, and repair must be performed by a qualied
technician or gas supplier.
• Do not store this product close to any gasoline and any ammable vapors
or liquids.
• Do not store this product close to an LP-cylinder.
• Failure to follow the directions of this manual may result in a re or explosion
and result in property damage, injury, or death.
• Do not burn solid fuels on this appliance.
• Inspect the burner at continued intervals while using this product.
• If any burner damage is present, the burner must be replaced prior to the
next usage.
• Burner replacements must be manufacturer-approved to ensure optimal
safety and damage prevention.
• Do not place any objects into the re pit. This appliance is designed to
operate with propane only.
• Do not use this product if the gas supply system has been submerged in
water. Contact a qualied technician to replace the parts as needed.
• Installation, operation, and storage of this appliance and propane gas must
comply with all local codes and regulations.
• Improper installation, service, or maintenance may result in property
damage, injury, or death. Please read and follow all directions thoroughly
before assembly, operation, or repair.
• This is not a toy. Improper use may result in injury or death. Children and
pets must be always supervised when this product is in use. Do not connect
this product to a remote gas supply.
CONSUMER
Retain this manual for future reference.

4[email protected]1-833-327-8625
• Your safety and the safety of others are important to us. This manual
provides safety guidelines to prevent any damage, injury, or death.
Please read all points thoroughly and follow these steps to ensure
optimal protection for you and your family.
• Keep this manual for future reference.
• Failure to follow this manual may result in property damage, injury, or death.
• This appliance and fuels used to operate this product may expose you to
chemicals, including benzene, which is known to the State of California to
cause cancer or reproductive harm. For more information, please visit
www.P65warning.ca.gov.
• During your rst use, you may hear a popping sound and see the lava rocks
bounce in the re pit for up to 30 minutes. Please maintain a safe distance
away from the re pit until the rocks settle and are no longer moving around.
For more information, please visit www.P65warning.ca.gov.
SAFETY GUIDE
BE CAREFUL
WARNING:
• Use this appliance in a well-ventilated outdoor area.
• Do not use this product in an enclosed area, such as a camper, tent,
car, or inside your home.
Installation of this product must conform with local codes or, in the
absence of local codes, with either the National Fuel Gas Code, ANSI
Z223.1/NFPA 42, Natural Gas and Propane Installation Code, CSA B149.1
or Propane Storage and Handling Code, B149.2. or the Standard for
Recreational Vehicles, ANSI A 119.2/NFPA 1192. and CSA Z240 RV series,
Recreational Vehicle Code, as applicable.

5EASTOAK.COM FIRE PIT TABLE
Thank you for trusting us with your purchase! We are excited for you to experience
warmth in luxury. To ensure the lifespan of your product, here are some care and
maintenance tips.
WARNING
• Before any service or maintenance, allow the heater to cool down completely.
This may take at least 45 minutes.
• Manufacturer and seller expressly disclaim any and all liability for personal
injury, property damage or losses, whether direct, indirect, or incidental,
resulting from the incorrect attachment, improper use, inadequate
maintenance, unapproved modication or neglect of this product.
MAINTENANCE
• Inspect all gas lines before each use. Check for any signs of extensive
abrasion, cuts, or wear.
• Perform a leak test annually or before operation with a newly-installed gas tank.
CLEANING (Exterior Surface)
• Clean the exterior surface with a damp cloth. Use a warm water and a mild
soap solution.
• Do not use any ammable or corrosive cleaning agents, such as bleach.
• Do not submerge this appliance in water. Submerging this product in water
may result in damage and must be replaced prior to the next use.
CLEANING (Burner)
• Ensure burner has completely cooled down.
• Remove all lava rocks from the re pit.
• Clean the burner with a soft-bristle brush and compressed air.
STORAGE
• Ensure the control knob and gas tank knob is set to the “OFF”
position.
• When not in use, disconnect the propane gas tank. Do not store
the gas tank in direct sunlight or excessive heat.
• Propane gas tanks must be stored outdoors in a well-ventilated space.
• Safely store this appliance upright. To ensure protection from any
damage resulting from extreme weather, such as rain, hail, snow,
dust, or debris, be mindful of outdoor placement.
• Be mindful of all gas lines and extensions from this appliance to
prevent personal injury, such as tripping over the product or parts of it.
• This product may only be stored indoors when it is disconnected
from all gas lines and cooled down.
CARE AND MAINTENANCE

6[email protected]1-833-327-8625
STOVEDIMENSIONS

7EASTOAK.COM FIRE PIT TABLE
PARTS DIAGRAM
size AA BB CC DD
44in. 14x 16x 1x 1x
52in. 14x 16x 1x 1x
57in. 18x 16x 1x 1x
B
A
AA BB CC DD
I
C
D
E
L
F
FGH

8[email protected]1-833-327-8625
1This product requires 2 people to assemble.
Before assembly, please read the entirety of this manual to ensure safety
and proper usage. Keep in mind there are a variety of steps.
Place all parts and hardware on a at surface. Inspect each piece and
ensure there is no damage or missing pieces. Please do not destroy or
discard any packaging until there is conrmation that all needed parts are
included for assembly.
Caution: Small components are used in the assembly of this appliance
and may present as a choking hazard. Please keep small children and
pets away during assembly to prevent any injury or death.
Plastic bags and packaging lm may present as a choking or suffocation
hazard. Please keep small children and pets away during assembly to
prevent any injury or death.
Install bracket (L) to panel (D,E) using 2 screws (AA).
ASSEMBLY INSTRUCTIONS
AA
D
E
L
L
2x
1x

9EASTOAK.COM FIRE PIT TABLE
2
3
Assemble the panels (E, F x2, G, H) as shown below
and secure them together using 8 screws (BB).
5Place the burner unit on top of the unit.
Fasten screws (BB x 4, I) tightly.
BB
BB
E
FF
G
H
8x
BB
BB
I
4x

10 [email protected]1-833-327-8625
4
5Secure center piece using 4 screws (BB x4). Align
two screws on the top side. Then, turn the unit upside
down and fasten two screws on the bottom side.
DD
DD
J
J
4x
4x
BB
BB
BB
G
4x
Secure door panel to unit using screws (DD x4, J x4).

11EASTOAK.COM FIRE PIT TABLE
6
The direction of the
front door faces the
direction of the heat
shield
AA 8x

12 [email protected]1-833-327-8625
7Place lava or glass rocks into the burner.
ATTENTION:
• Do not put more than 4 lbs of lava rocks or 9 lbs of
glass rocks into the burner.
• Do not touch or arrange the lava rocks once the
product is in use. If arrangement is needed, allow
the lava rocks to cool down completely before
doing so.
• Do not mix different types of rocks together.
• Do not put the table lid on the re pit when in use.
Ensure the re pit has cooled before placing the
table lid over the re pit.
A
K

13EASTOAK.COM FIRE PIT TABLE
LIQUEFIED PETROLEUM GAS (LPG) SAFETY INFORMATION
LPG cylinder used with the product must be:
• Constructed and marked in accordance with the U.S.Department of
Transportation (DOT) specication for LPG cylinder, CAN/CSAB339,
Cylinders, Spheres, and Tubes for the Transportation of Dangerous Goods,
as applicable;
• Arranged for vapor withdrawal.
• Provided with a tank collar to protect the tank valve.
• Provided with a listed overlling prevention device and a QCC I or Type I
(CGA810) LPG cylinder connection.
• Max capacity: 2olb.
• Max gas supply pressure: 250 PSI (1750 KPa)
• Min.gas supply for input adjustment: 25 PSI (175 KPa)
• Manifold pressure with regulator provided: 11in wc (2.74 KPa)
• Not stored in area with temperature over 125F / 51.5℃
ASSEMBLY INSTRUCTION
(LPG cylinder)

14 [email protected]1-833-327-8625
LPG cylinder connection
ASSEMBLY INSTRUCTION
(LPG cylinder)
• Inspect the entirety of the gasket for any sign of damage or erosion.
Position the LPG cylinder in the repit and secure the unit using the
retainer bolt.
• ATTENTION: Ensure the valve on the re pit and LPG cylinder are set
to the “OFF” position.
• Remove any protective caps on the LPG cylinder. Align the gas lines to
the LPG cylinder nozzle. Fasten the connection with a coupler.
• NOTE: Be mindful of cross threating. To avoid this, do not overtighten
screws and connections. The gas line should be tight enough without any
signs of wiggling or gaps between connections.
• Inspect the gas line and perform a leak test prior to each use (see page 12).

15EASTOAK.COM FIRE PIT TABLE
ASSEMBLY INSTRUCTION
(LPG cylinder)
Lighting Instructions
• Ensure the re pit control knob is set to the “OFF” position.
• Turn on the gas cylinder valve by pressing the knob and turning it
counterclockwise to the “IGNITOR” position. This is indicated by a lighting
symbol. Repeat this step 2-3 times as needed until burner ignites.
• Once the burner sparks, hold the control knob at the “LOW” position for 20
seconds. The low setting is indicated by “I”. Then, release the knob and turn
it counterclockwise to “HIGH” or “II”. Adjust the ame to your desired level.
NOTE: If the ignitor does not spark or a ame can not hold:
• Ignite the burner with a long lighter or match. Heat-resistant gloves is
highly advised to prevent any damage or injury.
• Press and turn the control knob to the “LOW” or “I” position. Hold for
20 seconds.
• Adjust the ame to your desired level.
• Keep in mind there may be a default 5-minute shut off period before the
burner can be re-ignited.
WARNING:
• Children and pets must be supervised when this appliance is in use. Do
not allow children and pets to come close to this unit.
• Keep clothing or any ammable material away from this appliance to
prevent any property damage, injury, or death.

16 [email protected]1-833-327-8625
OPERATION INSTRUCTION
(Turning Of f )
• To shut down the unit, turn the control knob clockwise to the “OFF” position.
• Turn off the gas cylinder and disconnect the regulator when appliance is
not in use.
• Allow adequate time for the heater to cool down completely before
transporting it.
WARNING:
• Ensure the LPG cylinder valve and control knob on the unit are completely
off to prevent gas leaks that my result in property damage, injury, or death.
Turning OFF

17EASTOAK.COM FIRE PIT TABLE
LPG cylinder disconnection
ASSEMBLY INSTRUCTION
(LPG cylinder)
• Allow unit to completely cool down after use. Then, ensure LPG cylinder
valve is shut and cooled down. Control knob on unit must be in the “OFF”
position.
• Next, turn the coupling nut counterclockwise until the regulator detaches.
• Place the protective cap on the LPG cylinder valve and store the cylinder
in outdoors in a well-ventilated area away from sunlight or excessive heat.
WARNING: LPG cylinder must be disconnected and removed prior to
transporting the re pit.
• DO NOT attempt to disconnect the gas regulator from the LPG cylinder
when the unit is in use or while it is still hot. Allow adequate time from the
appliance to cool down. This may take at least 45 minutes.
OPERATION INSTRUCTION
(Turning Of f )

18 [email protected]1-833-327-8625
OPERATION INSTRUCTION
(Leak Check)
AWARNING
• All leak tests must be performed outdoors.
• Extinguish all open ames in the appliance before testing for any leaks.
• DO NOT smoke when performing a leak test.
• DO NOT use the appliance until all connections have been tested and there
is conrmation that no leaks are present.
• Leak tests must be performed annualy or after any parts have been replaced.
• To check for leaks, make a solution of equal parts liquid detergent and water.
• Then, apply a small amount of solution on the gas system’s connections
and tubing.
• Next, turn on the LPG cylinder valve and inspect for any leaks.
If bubbles appear at any connection or part of the tubing, a leak is present:
• Turn the LPG cylinder valve to the “OFF” position immediately.
• Disconnect the LPG cylinder from the unit. Dry off all connections and tubing.
Then, reconnect the cylinder to the unit and perform another leak test.
• Do not use the appliance if there is a leak.
• You may need to call a qualied technician or the manufacturer for
replacement services.
• Until the parts are repaired or replaced, the LPG supply must be shut off,
disconnected, and removed from the appliance.
• Inspect the gas hose again after replacement and before the next use.
If no bubbles appear, the connection is secure and there are no leaks
present.
• Inspect gas hoses before use. If there is any evidence of extensive abrasion,
wear, or damage, it must be replaced prior to next use.