Chemin'Arte Oxford 119 User manual

www.cheminarte.com
INSTALLATIONAND USER INSTRUCTION GUIDE FOR
OXFORD ELECTRIC FIREPLACE

Read these instructions thoroughly before use and keep for future
reference.
Important Safety Instructions
When using this appliance, basic precautions should be followed to reduce the
risk of fire, electric shock, and injury to person, including the following:
·This heater must be used on anAC supply only and the voltage marked on the
heater must correspond to the supply voltage.
·Do not switch the appliance on until it properly installed as described in this
manual.
·The heater must not be located immediately below a socket outlet.
·Do not leave the appliance switched on when leaving your home or going to
sleep.
·Do not leave unattended when plug in to the mains supply.
·This heater is not intended for use by children.Never leave unsupervised children
where the heater is left switched ON (I) or unguarded.
·Only use the appliance for domestic purposes and in the way indicated in these
instructions.
·From time to time check the cord for damages. Never use the appliance if the
cord or any part of the appliance shows any signs of damage.
·If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualified persons in order to avoid a hazard.
·WARNING: In order to avoid overheating, do not cover or obstruct the heater in
any way.
·Do not use this heater in the immediate surroundings of a bath, a shower or a
swimming pool.
·Make sure the connection cord does not touch any hot surfaces.
·Keep the appliance at least 100cm (1.0m) from walls and any other combustible
materials.
·Do not use the appliance outdoors
·Do not use if you have wet hands.
·Never move the appliance by pulling the cord.
·Before cleaning the appliance, make sure it is unplugged from the mains power
and that it is completely cool
·Do not clean the appliance with abrasive or chemicals.
·Never use accessories that are not recommended or supplied by the manufacturer.
·Never route the mains cable beneath carpet.
·Never use aerosols or similar close to the heater.

·Never use the heater to dry clothes or any other similar items.
·In order to avoid a hazard due to inadvertent resetting of the thermal cut cut-out,
this appliance must not be supplied through an external switching device, such as
a timer, or connected to a circuit that is regularly switched on and off by utility.
·This heater must not be used with an extension lead.
·Do not use this heater with a programmer, timer or any other device that switches
the heater on automatically, since a fire risk exists if the heater is covered or
positioned incorrectly.
·Children should be supervised to ensure that they do not play with the appliance.
·This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience or
knowledge if they have been given supervision or instruction concerning use of
the appliance in a safe way and understand the hazards involved.
·Cleaning and user maintenance shall not be made by children without
supervision.
·Children of less than 3 years should be kept away unless continuously supervised.
·Children aged from 3 years and less than 8 years shall only switch on/off the
appliance provided that it has been placed or installed in its intended normal
operating position and they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children
aged from 3 years and less than 8 years shall not plug in, regulate and clean the
appliance or perform user maintenance.
·WARNING: This heater is not equipped with a device to control the room
temperature. Do not use this heater in small rooms when they are occupied by
persons not capable of leaving the room on their own, unless constant supervision
is provided.
·CAUTION- Some parts of this product can become very hot and cause burns.
Particular attention has to be given where children and vulnerable people are
present.
Getting Started
·Remove the appliance from the box.
·Remove any packaging from the appliance.
·Place the packaging inside the box and either store or dispose of safely.
Contents of Carton
·Heater.
·Fixing bracket and screws
·Remote control.
·1 Instruction Manual.
Helpful Advice before Fitting
·Please retain all packaging until you have checked and counted all the parts and
the contents of the fixing pack against the parts list.

·The fixing pack contains small items which should be kept away from young
children.
Installation Instructions
·Do not connect the appliance until the instructions are read carefully and the
heater properly and securely installation.
·The minimum distances must be observed.
·Make sure the opening dimensions of mantel are at least 595mm width and
435mm height.
·Make sure the distance from the rear of heater to the wall is at least 100mm.
·Make sure the distances from the left, right and top of heater to the wall are at
least 100mm.
·Inset the heater carefully into the opening of mantel.
·Fix the heater securely on the hearth by supplied bracket and screws (see Fig.1 in
circle)

Operation Instructions
The Controls
▪Switching ON/OFF
·Use the ON/OFF switch to power on the heater (set it to standby mode).
·In standby mode, the heater can be operated either manually by the switches
located at the front and right hand side of heater or by the supplied remote
control.
▪Manual Operation
·NOTE: The heater only starts working if the set temperature is higher than the
ambient room temperature.
▪Remote Operation
·NOTE: The heater should be powered on using the ON/OFF switch before it can
be operated using remote control.
Heater powered off
Heater powered on, set to standby mode
-Press to switch the flame effect ON/OFF
-Press and hold to toggle between 5 different
flame dim levels
Press to activate low level heating(1000W)
Press to activate high level heating(2000W)

·The remote control requires 2xAAA size batteries (Not included).
·Open the battery compartment by sliding the cover down and insert the batteries
noting the polarity indicated in the battery compartment.
·Keep batteries out of reach of children.
·Remote control operations are identical to the functions on the control panel.
·The remote control must be point directly at the sensor on control pad.

Display
Settings
▪Setting weekday and time
·Press the DATE/TIME key. When the day is flashing press the ▲or ▼key to
select the day.
·Press the DATE/TIME key again, then press the + or –key to set the hour.
·Press the DATE/TIME key again, then press the + or –key to set the minute.
·Press the OK key to confirm the setting.
▪Setting temperature
·NOTE: This setting is only applicable for the temperature in standard heating
mode, not for the temperature in the timer mode. The default set temperature is
20℃.
·NOTE: The heater only starts working when the set temperature is higher than
the room temperature.
·Press the + or –key to set the temperature, which ranges from 15 to 30℃.
·After the temperature setting has been completed, the display flashes about 5
seconds, then shows the room temperature.
▪Setting timer
·Up to 10 different timer settings can be programmed.
·Each timer setting has its day, power-on time and power-off time.
·The maximum duration of each timer setting is 23 hours 50 minutes.
·If the power-off time of the timer setting falls on the following day, it is

unnecessary to set the day-just set the power-off time.
·Press the TIMER SET key, the timer number starts blinking (01-10).
·Press the + or –key to select a timer number.
·Press the TIMER SET key, the cursor on the left side of the day blinks.
·Press the ▲or ▼key to move the cursor to the corresponding day. Press the +
key to add a corresponding day, or press the - key to delete a day.
·Press the TIMER SET key to set the on time. The hour digit starts blinking.
·Press the + or –key to set the hour.
·Press the TIMER SET key. The minute digit starts blinking.
·Press the + or –key to set the minute.
·Press the TIMER SET key to set the off time. The hour digit starts blinking.
·Press the + or –key to set the hour.
·Press the TIMER SET key. The minute digit starts blinking.
·Press the + or –key to set the minute.
·Press the TIMER SET key. The temperature digit starts blinking.
·Press the + or –key to set the temperature.
·Press the TIMER SET key to continue with the timer setting or press the OK key
to confirm the setting.
▪Viewing the timer setting
·Press the TIMER SET key.
·Press the + or –key to check the power-on time of the set timers one by one.
·To check the power-off time, press the ▲key.
·Press the + or –key to check the power-off time of the set timers one by one.
·To delete selected setting, press the C key.
▪Activation timer
·Press the TIMER ON/OFF key to activate the timer function.
·NOTE: When the timer is active, the heating level must be manually selected. If
the heater function is not selected; only the flame effect goes on at the set
power-on time.
▪Open window detection
·Press the key to activate open window detection function. The
icon appears on the display.
·The icon on the display starts blinking and the heater stops heating if
room temperature drops quickly. Press the key again to cancel open
window detection.
·NOTE: Open window detection does not work if you have not turned heating on.

Maintenance
·WARNING: Before any maintenance and/or cleaning the exterior of the heater,
disconnect the heater form the power supply and leave heater cooled off.
·The heater uses an electronically controlled LED system to create the flame effect
therefore no parts need to be replaced. Under no circumstances should the heater
be serviced by anyone other than a qualified electrician.
Safety Cut-out
·This heater is fitted with a safety cut-out which will operate if the heater
overheats (e.g. Due to blocked air vents). For safety reasons, the heater will NOT
automatically reset.
·To reset the heater, disconnect the heater from the mains supply for at least 15
minutes. Reconnect the supply to the mains and switch on the heater.
Care and Cleaning
·Always disconnect the heater from mains supply and allow cooling before any
cleaning operation.
·Trim parts may be cleaned using a clean, damp cloth. Never use abrasive cleaners
and chemical agents as damage may occur to the finish.
Technical Specification
·Supply: 220-240V~ 50Hz
·Rated power: 2000W
·Lighting: LEDs

General Information
Model
Oxford 119
Item
Symbol
Value
Unit
Item
Unit
Heat output
Type of heat input, for electric storage local
space heaters only (select one)
Nominal heat output
Pnom
2.0
KW
manual heat charge control,
with integrated thermostat
Not
applicable
Minimum heat output
(indicative)
Pmin
0.0
KW
manual heat charge control
with room and/or outdoor
temperature feedback
Not
applicable
Maximum continuous heat
output
Pmax,c
2.0
KW
electronic heat charge control
with room and/or outdoor
temperature feedback
Not
applicable
Auxiliary electricity consumption
fan assisted heat output
Not
applicable
At nominal heat output
elmax
0.000
KW
Type of heat output/room temperature
control (select one)
At minimum heat output
elmin
0.000
KW
single stage heat output and no
room temperature control
[no]
In standby mode
elSB
0.000
W
Two or more manual stages, no
room temperature control
[no]
with mechanic thermostat room
temperature control
[no]
with electronic room
temperature control
[no]
electronic room temperature
control plus day timer
[no]
electronic room temperature
control plus week timer
[yes]
Other control options (multiple selections
possible)
room temperature control, with
presence detection
[no]
room temperature control, with
open window detection
[yes]
with distance control option
[no]
with adaptive start control
[no]
with working time limitation
[no]
with black bulb sensor
[no]
Contact details
www.cheminarte.com

Disposal Information
This making indicated that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return
your used device, please use the return and collection systems or contact the
retailer where the produce was purchased. They can take this product for
environmental safe recycling.