Chesney's EFB1200 Instruction Manual

1
Bio-Ethanol Installation & User Manual
model: EFB1200
CHESNEY’S
Issue 01

2
Thank you for choosing this Chesney’s Bio-Ethanol fire.
Please read this information guide carefully in order to
safely install, use and maintain your product.

3
Contents
Section A: Installation Guide
Installation 4
Housing configurations 12
Section B: User Manual
I. Safety 20
II. Operation 22
Operating Elements 22
Initial start-up of the device 24
Flame size regulation 27
SLEEP function 28
Extinguishing the appliance 28
Subsequent start-up 28
Switching off 29
Information and warning alert 30
III. Customer’s Menu 33
Locking the appliance 33
Child lock 34
Set time 35
Device IP 35
Remote control 36
Fast start 37
Serial number 37
Software 37
IV. Cleaning and maintenance 38
V. Fuel 39
VI. Disposal and recycling 39

4
H 237mm (9 5/16”)
H1 183mm (7 3/16”)
H2 180mm (7 1/16”)
H3 3mm (1/8”)
L 1190mm (46 7/8”)
L1 1000mm (39 3/8”)
L2 95mm (3 3/4”)
L3 95mm (3 3/4”)
D 280mm (11”)

5
• Do not install the appliance in areas with a cubic capacity of less than 178m3/
6286ft3(68m2/ 732ft2with a height of less than 2.6m / 8.53ft).
• Do not install the appliance near fans, vents or anything that can cause
significant draughts of air.
• Do not place in areas where there might be a potentially explosive
atmosphere of paint vapours, industrial dusts, etc.
• No ammable items should be placed in direct contact or within a radius of
1m / 3.28ft of the appliance. Do not place near curtains, net curtains, etc.
• Do not expose to external weather conditions. The product is for internal use
only.
• Do not place the appliance in close proximity to sources of humidity.
• It is obligatory to have a carbon-dioxide (CO2) or dry chemical extinguisher
placed nearby the appliance.
• Installation of the appliance must allow for easy removal of the appliance for
servicing.
• The room in which the appliance is to be installed must have sufcient
ventilation to ensure air exchange in the room at least once per hour.
• Do not start the appliance before full installation has been completed.
• Do not ll the fuel container before placing the appliance into its nal position.
Section A: Installation Guide

6
INSTALLATION
NOTE! If you plan to operate the bio fireplace with a device that has a
WI-FI connection (e.g. smartphone, tablet) please acquaint yourself with
the content of the Configuration of the module with Wi-Fi and Smart Home
System manual before installing the fireplace in the building.
- After opening the packaging box leave the device inside the box for
approx. 2 hours until it reaches room temperature. During this time
familiarize yourself with the user’s and installation manuals.
- The elements of construction used over the appliance must be made of
non-ammable materials.
- Any recess below the appliance must be sealed.
- A loose cable min. 3 x 1.5 mm2, with power supply 230V, 50Hz must be
provided to connect the appliance to the mains.
- The device can be wired directly into a fused spur or alternatively a
standard 3 pin 13 amp mains plug can be fitted (not supplied).
- If there is going to be a cover over the appliance, it must be made of
non-ammable materials and the minimum distance from the appliance
must be no less than 40cm / 15 ¾”.
For reasons of safety, under no circumstances can there be any
ammable material within a 1m radius of the appliance.
The manufacturer does not recommend placing any heat
sensitive materials or devices above the appliance as it can
signicantly affect the materials, properties and lifetime.
The manufacturer will not bear any responsibility for the
damage caused to any heat sensitive materials or devices
installed above the appliance.

7

8
How to construct the housing for the appliance:
Make a cavity for the appliance following the diagram below. Ensure that
the plane within the cavity on which the appliance is to be installed is
level.
The difference in level between the ends of the appliance must not
exceed 2mm. Poor levelling may cause abnormal operation of the
appliance and, in extreme cases, it can cause leaks of the bio-ethanol fuel
and the danger of fire.
Then connect the supplied cable with a connection block at the end of
the cord. Note that connection to the mains must be made by a qualied
electrician.

9
Highlighted button indicates proper connection of the appliance to
the power supply. Once connected to the power source the appliance
should be placed in the prepared cavity, by using attached handles.
Please make sure to remove the handles before starting the appliance
and keep them for the lifetime of the appliance. If necessary, use the
handles to remove the appliance.
Handle
Connection to the
mains must be
made by a qualified
electrician.

10
Installing the glass shield to the appliance:

11
Situations where the installation of the glass shield with the appliance is
necessary:
Situations in which installation of a glass shield is forbidden:
ATTENTION!
• Make sure that the appliance has been correctly installed and read the
attached instruction manual.
• You must not ll the fuel tank and start the appliance before reading
the instruction manual.
• If in the future it is necessary to take the appliance out of the housing,
wait until the fuel has burned-up completely and the display shows NO
FUEL, disconnect the power supply and take the appliance out of its
housing.
• Keep this instruction manual throughout the lifetime of the appliance.

12
Guide for designing the housing for the appliance

13
Installing an optional glass fascia

14
Mounting a heat sensitive item such as a TV above the replace

15
Installation with a two sided open setting

16
Free-standing installation of the appliance

17
Ventilation and air conditioning in the room in relation to installation of
the appliance

18
Using an existing chimney ue

19
Section B: User Manual

20
This is a decorative appliance with real ames. In
order to use the device properly and safely and in
order to keep the warranty, the following safety rules
should be observed. This is not a heating device.
I. Safety
• The device should be installed in accordance with to the installation
manual.
• While working, the device emits heat, water vapour and carbon
dioxide, therefore it is necessary for the appliance to only be installed in
a room of appropriate cubic capacity and with adequate ventilation.
• During the start-up sequence of the device, the characteristic smell of
the liquid used in the device may be perceptible.
• It is obligatory to have a carbon-dioxide or dry chemical extinguisher
placed nearby the device.
• A device that is in operation on must not be moved. Wait for complete
fuel burn-out, disconnect the power supply and cool down the elements
before moving the device.
• The device should not be left without adult supervision.
• Prevent handling of the device by persons not trained in its use.
• Do not attempt to make changes or repairs to the construction of
the device. Repairs can be made only by a person trained to service the
device.
• Do not attempt to pour fuel into the device when lit as it may cause
damage to the device and cause fire. Pouring fuel into a lit device may
cause a sudden ignition and can cause re, burns and a risk to life.
• Do not heat the fuel before starting-up the device.
• Do not start up the device if any fuel has been spilt.
• Do not cover a working device as it may cause re.