Chesney's SALISBURY Instruction Manual

CHESNEYS
GAS EFFECT STOVES
STANDARD, LARGE
& LOG BURNER OPTION
INSTALLATION & USER MANUAL
www.chesneys.co.uk
Version 023 April 2023
IMPORTANT:
PLEASE ENSUREYOU REGISTER FOR YOUR EXTENDED
WARRANTY. PLEASE SEE PAGE 80 & 81 FOR DETAILS

2
Technical Manual
Technical PIN: 0359CS1578
User and Installation Instructions
Model No.
Standard Gas Stoves:
Salisbury
Beaumont
Shoreditch (Available at a later date)
Shoreditch LS (Available at a later date)
Shoreditch XLS (Available at a later date)
Large Gas Stoves:
Salisbury
Beaumont
Shoreditch (Available at a later date)
Belgravia (Available at a later date)
Shipton (Available at a later date)
Large Gas Log Stoves:
Salisbury
Beaumont
Shoreditch (Available at a later date)
Belgravia (Available at a later date)
Shipton (Available at a later date)
IMPORTANT:
Please read these instructions
carefully before installation or use.
These instructions are only valid if the
following country code is on the appliance.
This appliance must be installed and serviced by a qualified
person in accordance with local and national regulations.
The flue system must be installed and inspected by a qualified
person in accordance with local and national regulations.

3
Contents
Section Pages
1 Unpacking 5-6
2 Technical Data 7-10
3 Installation Parameters 11-13
4 Burner and Control Information 14-17
5 Construction Information 18-30
6 Appliance Details 31
7 Preparing the Appliance for Installation 32
8 Installation 33-36
9 Placement of Fibre Logs, Chippings and Embers 37-47
10 Commissioning the Fire Unit 48-50
11 Briefing and Handover to the Customer 51
12 Servicing and Maintenance 52-53
13 Fault Finding 54-55
14 User Instructions 57-60
15 Control System Information 61-71
16 Annex A: Balanced Flue Conversion 72-74
17 Installer Commissioning Checklist 75
18 Dealer and Installer Information 77
19 Annual Service Record 78-79
20 Chesneys Warranty Information and Registration 80-81

4

5
1. Unpacking
Remove the appliance from its packaging, check that it is complete and
undamaged.
If satisfied by the condition and the contents is as specified, proceed with the
installation.
The installation should only be carried out by a competent person and all gas
work must be carried out by a Gas Safe registered person in accordance with
national and local regulations for both gas and electricity (If required).
The installation must comply with local and national building regulations.
For the Republic of Ireland, reference should be made to IS813 and ICP3 and any
guidance notes from Board Gais.
Failure to comply with the regulations nullifies ALL guarantees.
Parts:
Fig.1 Gas Stove Appliance Fig.2 Installation Manual / Warning Label
Fig.3 Burner Assembly

6
Fig.6 Remote Control Handset
Fig.4 Logs
OR
Fig.5 Bag of embers
Fig.8 Glow strands
Standard Stove Large Stove
Fig.7 Stainless steel panels
Large Stove - Log Burner

7
2E/2 (43.46-45.3 MJ / m3 (0°C))
2.Technical Data
Gas Connection Size 8.0mm O.D. tubing
Control System TESC (Thermo Electric Safety Control)
Appliance Mass Range (kilograms) 79kg – 155kg
Gas
Type
Gas Category,Type and
Supply Pressure
Countries of Destination
AT
BE
BG
CH
CY
CZ
DE
DK
EE
ES
FI
FR
GB GR
HU
HR
NG
I2H - G20 at 20mbar           
I2E - G20 at 20mbar 
I2E+ - G20 G25 at 20/25mbar  
I2ELL - G25 at 20mbar 
LPG
I3B/P(30) - G30/G31 at 30mbar           
I3+ - G30/G31 at 30/37mbar        
I3P(50) - G31 at 50mbar   
I3P(37) - G31 at 37mbar        
I3P(30) - G31 at 30mbar 
Gas
Type
Gas Category,Type and
Supply Pressure
Countries of Destination
IE IT
LT
LU
LV
MT
NL
NO
PL
PT
RO
SE
SI
SK
TR
NG
I2H - G20 at 20mbar          
I2E - G20 at 20mbar   
I2L - G20 G25 at 25mbar 
I2EK - G25.3 at 25mbar 
LPG
I3B/P(30) - G30/G31 at 30mbar   
I3+ - G30/G31 at 30/37mbar       
I3P(50) - G31 at 50mbar  
I3P(37) - G31 at 37mbar         
I3P(30) - G31 at 30mbar  

8
STANDARD GAS STOVE CONVENTIONAL FLUE
GasType
Gas Category,Type
and Supply Pressure
Heat Input Gross kW
Heat Input Nett kW
Gas Rate m3/h
Burner Pressure
Injector marking
Pilot Assembly
Efficiency Class
NOx Class
NG
I2H - G20 at 20mbar 5.3 4.8 0.49 18.5
320
SIT 9043
or
ERTA
PG-82-330
1 4
I2E - G20 at 20mbar 5.3 4.8 0.49 18.5
I2E+ - G20/G25 at 20/25mbar 5.3/5 4.8/4.5 0.49/0.53 18.5/23.6
I2ELL - G25 at 20mbar 4.4 4 0.47 18.5
I2L - G25 at 25mbar 5 4.5 0.53 23.6
I2EK - G25.3 at 25mbar 5 4.5 0.53 23.6
LPG
I3B/P(30) - G30/G31 at 30mbar 5 4.6 0.14 28
140
SIT 9228
or
ERTA
PG-82-350
1 4
I3+ - G30/G31 at 30/37mbar 4.5/5 4.2/4.6 0.17/0.185 28/36
I3P(50) - G31 at 50mbar 5 4.6 0.185 36
I3P(37) - G31 at 37mbar 5 4.6 0.185 36
I3P(30) - G31 at 30mbar 4.5 4.2 0.17 28
STANDARD GAS STOVE BALANCED FLUE
GasType
Gas Category,Type
and Supply Pressure
Heat Input Gross kW
Heat Input Nett kW
Gas Rate m3/h
Burner Pressure
Injector marking
Pilot Assembly
Efficiency Class
NOx Class
NG
I2H - G20 at 20mbar 5.3 4.8 0.49 18.5
320
G30-ZP
312
(31.2 INJ)
1 4
I2E - G20 at 20mbar 5.3 4.8 0.49 18.5
I2E+ - G20/G25 at 20/25mbar 5.3/5 4.8/4.5 0.49/0.53 18.5/23.6
I2ELL - G25 at 20mbar 4.4 4 0.47 18.5
I2L - G25 at 25mbar 5 4.5 0.53 23.6
I2EK - G25.3 at 25mbar 5 4.5 0.53 23.6
LPG
I3B/P(30) - G30/G31 at 30mbar 5 4.6 0.14 28
140
G30-ZP
2-271
(27.1 INJ)
1 4
I3+ - G30/G31 at 30/37mbar 4.5/5 4.2/4.6 0.17/0.185 28/36
I3P(50) - G31 at 50mbar 5 4.6 0.185 36
I3P(37) - G31 at 37mbar 5 4.6 0.185 36
I3P(30) - G31 at 30mbar 4.5 4.2 0.17 28

9
LARGE GAS STOVE BALANCED FLUE
GasType
Gas Category,Type
and Supply Pressure
Heat Input Gross kW
Heat Input Nett kW
Gas Rate m3/h
Burner Pressure
Injector marking
Pilot Assembly
Efficiency Class
NOx Class
NG
I2H - G20 at 20mbar 6.9 6.2 0.64 13.2
Front
280
Rear
220
SIT 9043
or
ERTA
PG-82-330
1 4
I2E - G20 at 20mbar 6.9 6.2 0.64 13.2
I2E+ - G20/G25 at 20/25mbar 6.9/6.5 6.2/5.9 0.64/0.675 13.2/16.6
I2ELL - G25 at 20mbar 5.7 5.1 0.6 13.4
I2L - G25 at 25mbar 6.5 5.9 0.675 16.6
I2EK - G25.3 at 25mbar 6.5 5.9 0.675 16.6
LPG
I3B/P(30) - G30/G31 at 30mbar 6.9 6.4 0.195 27
Front
120
Rear
80
SIT 9228
or
ERTA
PG-82-350
1 4
I3+ - G30/G31 at 30/37mbar 6.2/6.9 5.7/6.4 0.229/0.254 28/35
I3P(50) - G31 at 50mbar 6.9 6.4 0.254 35
I3P(37) - G31 at 37mbar 6.9 6.4 0.254 35
I3P(30) - G31 at 30mbar 6.2 5.7 0.229 28
LARGE GAS STOVE CONVENTIONAL FLUE
GasType
Gas Category,Type
and Supply Pressure
Heat Input Gross kW
Heat Input Nett kW
Gas Rate m3/h
Burner Pressure
Injector marking
Pilot Assembly
Efficiency Class
NOx Class
NG
I2H - G20 at 20mbar 6.9 6.2 0.64 13.2
Front
280
Rear
220
SIT 9043
or
ERTA
PG-82-330
1 4
I2E - G20 at 20mbar 6.9 6.2 0.64 13.2
I2E+ - G20/G25 at 20/25mbar 6.9/6.5 6.2/5.9 0.64/0.675 13.2/16.6
I2ELL - G25 at 20mbar 5.7 5.1 0.6 13.4
I2L - G25 at 25mbar 6.5 5.9 0.675 16.6
I2EK - G25.3 at 25mbar 6.5 5.9 0.675 16.6
LPG
I3B/P(30) - G30/G31 at 30mbar 6.9 6.4 0.195 27
Front
120
Rear
80
SIT 9228
or
ERTA
PG-82-350
1 4
I3+ - G30/G31 at 30/37mbar 6.2/6.9 5.7/6.4 0.229/0.254 28/35
I3P(50) - G31 at 50mbar 6.9 6.4 0.254 35
I3P(37) - G31 at 37mbar 6.9 6.4 0.254 35
I3P(30) - G31 at 30mbar 6.2 5.7 0.229 28

10
V2 LARGE GAS LOG STOVE CONVENTIONAL FLUE
GasType
Gas Category,Type
and Supply Pressure
Heat Input Gross kW
Heat Input Nett kW
Gas Rate m3/h
Burner Pressure
Injector marking
Pilot Assembly
Efficiency Class
NOx Class
NG
I2H - G20 at 20mbar 6.9 6.2 0.64 16.5 Centre
Burner
100
Log L/H
160
Log R/H
160
SIT
9043
or
ERTA
PG-
82-330
1 4
I2E - G20 at 20mbar 6.9 6.2 0.64 16.5
I2E+ - G20/G25 at 20/25mbar 6.9/6.5 6.2/5.9 0.64/0.675 16.5/16.8
I2ELL - G25 at 20mbar 5.7 5.1 0.6 16.5
I2L - G25 at 25mbar 6.5 5.9 0.675 19.8
I2EK - G25.3 at 25mbar 6.5 5.9 0.675 19.8
LPG
I3B/P(30) - G30/G31 at 30mbar 6.9 6.4 0.2 23 Centre
Burner
60
Log L/H
100
Log R/H
100
SIT
9228
or
ERTA
PG-
82-350
1 4
I3+ - G30/G31 at 30/37mbar 6.2/6.9 5.7/6.4 0.229/0.254 23/33
I3P(50) - G31 at 50mbar 6.9 6.4 0.254 33
I3P(37) - G31 at 37mbar 6.9 6.4 0.254 33
I3P(30) - G31 at 30mbar 6.2 5.7 0.229 23
V2 LARGE GAS LOG STOVE BALANCED FLUE
GasType
Gas Category,Type
and Supply Pressure
Heat Input Gross kW
Heat Input Nett kW
Gas Rate m3/h
Burner Pressure
Injector marking
Pilot Assembly
Efficiency Class
NOx Class
NG
I2H - G20 at 20mbar 6.9 6.2 0.64 16.5 Centre
Burner
100
Log L/H
160
Log R/H
160
Polidoro
446.1385.24 1 4
I2E - G20 at 20mbar 6.9 6.2 0.64 16.5
I2E+ - G20/G25 at 20/25mbar 6.9/6.5 6.2/5.9 0.64/0.675 16.5/16.8
I2ELL - G25 at 20mbar 5.7 5.1 0.6 16.5
I2L - G25 at 25mbar 6.5 5.9 0.675 19.8
I2EK - G25.3 at 25mbar 6.5 5.9 0.675 19.8
LPG
I3B/P(30) - G30/G31 at 30mbar 6.9 6.4 0.2 23 Centre
Burner
60
Log L/H
100
Log R/H
100
Polidoro
446.1385.44 1 4
I3+ - G30/G31 at 30/37mbar 6.2/6.9 5.7/6.4 0.229/0.254 23/33
I3P(50) - G31 at 50mbar 6.9 6.4 0.254 33
I3P(37) - G31 at 37mbar 6.9 6.4 0.254 33
I3P(30) - G31 at 30mbar 6.2 5.7 0.229 23

11
3. Installation Parameters
This appliance must be installed in accordance with the rules in force, and used only
in a sufficiently ventilated space. Consult instructions before installation and use of
this appliance.
NOTE - Wear protective clothing when fitting or carrying works out on the appliance.
For your safety it is law that all gas appliances must be installed by a competent
person.
The installation must be carried out in accordance with the relevant local and national
specifications and comply with current Building Regulations.
Chesneys recommend the fitting of a Carbon Monoxide detector that conforms to
EN 50291 wherever a gas appliance is installed.
Due to the unpredictability of the draught in existing flues and chimneys Chesneys
recommends the use of a liner for this product in accordance with local and national
regulations.
The use of leak detector around the gas valve is NOT recommended due to moisture
being able to enter and damage the valve.
NOTE -The flue must not be shared with any other appliance.
If the chimney has been used for solid fuel, the chimney must be swept before
installation.
The flue must be fitted in accordance with local and national regulations.
Damper plates or restrictor plates must not be fitted in the flue.
The flue must be inspected by a competent person and passed for use with the
appliance.
It is advised that a flue specialist inspect the flue system on an annual basis to ensure
that the flue system is sound and the combustion products outlet (terminal) is clear of
obstruction.
The flue system should only be fitted to the appliance where the chimney serving the
appliance:
a) Has passed a flue flow test to ensure that the flue is sound and without leaks; and
b) Has been swept if previously used for solid fuel.
IMPORTANT NOTE - Balanced Flue
The appliance is designed to fit numerous installation situations as listed in these
installation instructions. However only flue approved by Chesneys for this appliance
may be used. If the appliance is installed on non-Chesneys approved parts, Chesneys
cannot guarantee or accept and responsibility for the proper and safe working of the
appliance.

12
The flue system must be constructed from the appliance upwards, with all joints being
fully locked and sealed using the Chesneys specified parts.
Do not install the appliance in a bathroom or a room that contains a bath or shower.
It is advised that provisions be made for the removal of the appliance without the
need to dismantle the flue system.
Before the appliance is installed, the flue / chimney must be inspected to ensure that it
is structurally sound and free from obstructions.
Ensure the builders opening and supports are made of non combustible and heat
resistant material.
Do not cover the appliance and or do not wrap it in an insulation blanket or any other
material.
Do not make any changes to the appliance.
The gas connection must be in accordance with local and national regulations.
The use of a gas detection device is preferred method when investigating all
connections to the rear of the gas control valve. Please note the use of leak detector
fluid around the gas control valve is NOT recommended due to moisture being able to
enter and damage the valve.
Ventilation
GB current British Standard BS5440 appliances classified under 7kW (net) do not
require permanent ventilation.
NOTE - Ventilation requirements in other countries may vary please consult with
national regulations in your country.
WARNING - SPILLAGE MONITORING SYSTEM
The pilot light and flame sensing device fitted to this appliance is also an atmospheric
sensing device, this is not adjustable and must not be put out of action. If the pilot
light is damaged or faulty it should only be replaced with an original genuine unit
supplied by Chesneys.
When using stone like materials and or plaster finishing, the chimney breast should
dry for at least 6 weeks to prevent cracks.
The appliance is not fitted with an integral guard. It is recommended that a guard be
used for the protection of young children, the elderly or infirm and also for normal use
conforming to BS8423:2002, such that access to the hot appliance is minimised.
Do not place combustible materials directly in front of the appliance.
In case of a damaged or broken glass, do not use the appliance and isolate the gas to
the appliance.

13
THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE RULES IN FORCE AND ONLY USED IN A
SUFFICIENTLY VENTILATED SPACE. CONSULT INSTRUCTIONS BEFORE INSTALLATION AND USE OF THIS APPLIANCE.
COUNTRIES OF
DESTINATION
AT, BE, BG, CH, CY, CZ, DE,
DK, EE, ES, FI, FR, GB, GR,
HU, HR, IE, IT, LT, MT, NL, NO,
PL, PT, RO, SE, SI, SK,TR
CHESNEYS
194-204 Battersea Park Road, London, SW11 4ND
Tel: [phone] www.chesneys.co.uk
2575-17 0359-17
LARGE GAS STOVE C/F
SERIAL NUMBER: PIN: 0359CR1578
SPILLAGE TEST
TESTTHE APPLIANCE FOR SPILLAGE AFTER AN INITIAL 10 MINUTES OF OPERATION ON A MAXIMUM RATE. PLACE A
SMOKE MATCH BELOWTHE APPLIANCE APPROXIMATELY 50MM IN FROMTHE FRONT.THE SMOKE SHOULD BE DRAWN
INTOTHE APPLIANCE. IF SPILLAGE OCCURSTURN OFF THE APPLIANCE AND REFER TOTHE INSTALLATION MANUAL.
GAS CATEGORY,TYPE AND
SUPPLY PRESSURE
(LPG G30/G31)
HEAT INPUT
(GROSS) KW
HEAT INPUT
(NETT) KW
GAS RATE
M
3
/H
BURNER
PRESSURE MBAR
EFFICIENCY
CLASS
I
2H,
I
2E
- G20 AT 20MBAR
6.9 6.2 0.64 13.2
1
I
2E+
- G20/G25 AT 20/25MBAR
6.9 / 6.5 6.2 / 5.9 0.64 / 0.675 13.2 / 13.6
I
2ELL
- G25 AT 20MBAR
5.7 5.1 0.6 13.4
I
2L
- G25 AT 25MBAR
6.5 5.9 0.675 16.6
I
2EK
- G25.3 AT 25MBAR
6.5 5.9 0.675 16.6
MODEL:
()
BEAUMONT SALISBURY SHOREDITCH BELGRAVIA SHIPTON
THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE RULES IN FORCE AND ONLY USED IN A
SUFFICIENTLY VENTILATED SPACE. CONSULT INSTRUCTIONS BEFORE INSTALLATION AND USE OF THIS APPLIANCE.
COUNTRIES OF
DESTINATION
AT, BE, BG, CH, CY, CZ, DE,
DK, EE, ES, FI, FR, GB, GR,
HU, HR, IE, IT, LT, MT, NL, NO,
PL, PT, RO, SE, SI, SK,TR
CHESNEYS
194-204 Battersea Park Road, London, SW11 4ND
Tel: [phone] www.chesneys.co.uk
2575-21 0359-21
LARGE GAS STOVE B/F
LOG BURNER
SERIAL NUMBER: PIN: 0359CR1578
SPILLAGE TEST
TESTTHE APPLIANCE FOR SPILLAGE AFTER AN INITIAL 10 MINUTES OF OPERATION ON A MAXIMUM RATE. PLACE A
SMOKE MATCH BELOWTHE APPLIANCE APPROXIMATELY 50MM IN FROMTHE FRONT.THE SMOKE SHOULD BE DRAWN
INTOTHE APPLIANCE. IF SPILLAGE OCCURSTURN OFF THE APPLIANCE AND REFER TOTHE INSTALLATION MANUAL.
GAS CATEGORY,TYPE AND
SUPPLY PRESSURE
(LPG G30/G31)
HEAT INPUT
(GROSS) KW
HEAT INPUT
(NETT) KW
GAS RATE
M
3
/H
BURNER
PRESSURE MBAR
EFFICIENCY
CLASS
I
2H,
I
2E
- G20 AT 20MBAR
6.9 6.2 0.64 16.5
1
I
2E+
- G20/G25 AT 20/25MBAR
6.9 / 6.5 6.2 / 5.9 0.64 / 0.675 16.5 / 16.8
I
2ELL
- G25 AT 20MBAR
5.7 5.1 0.6 16.5
I
2L
- G25 AT 25MBAR
6.5 5.9 0.675 19.8
I
2EK
- G25.3 AT 25MBAR
6.5 5.9 0.675 19.8
MODEL:
()
BEAUMONT SALISBURY SHOREDITCH BELGRAVIA SHIPTON
Clean the glass before you use the appliance in order to prevent dirt from burning on
the glass.
All appliances are supplied with a metal data plate attached to it and must remain
with the appliance for annual services.
The data plate is attached to the rear of the appliance (see fig.9)
NOTE: DO NOT attempt to remove the data plate while the appliance is HOT!
Fig.9a
Fig.9b

14
4. Burner and Control Information
Fig.10

15
Dimensions
Fig.10a S8 CF Std
Fig.10b S8 CF Log

16
Fig.10c S8 BF Std
Fig.10d S8 BF Log

17
Burner Control Systems
Fig.11
1.THERMACO -THERMO ELECTRIC SAFETY CONTROL (TESC)
PILOT ASSEMBLY
SIT NG
HANDSET RADIO FREQUENCY

18
5. Construction Information
Hearths
A hearth shall be provided according to National regulations, in Great Britain this
would be to Building Regulation Document J and BS5871-1. A Hearth shall be
provided for the stove extending to at least the front of the supporting legs, and to
at least each side of the stove.The edge of the hearth should be marked to provide a
warning to the building occupants and to discourage combustible floor finishes such
as carpet being laid too close to the appliance. A way of achieving this would be to
provide a change in level.
Chesneys recommend a hearth footprint 50mm more on all 4 sides than the footprint
of the appliance.The hearth shall have a minimum thickness of 12mm.
Emissions Exit ConnectionTypes:
1. Conventional Flue
2. Balanced Flue
Conventional Flue
A smoke pellet can be used to test the flue for effectiveness of the draw, light the
smoke pellet and place to the base of the chimney/liner. Check other parts of the
dwelling (including loft areas) for leakage, down draught etc. If the smoke is drawn
into the chimney/liner without problem, continue with the installation.
If there is little or no flow into the chimney preheat the chimney and repeat the smoke
test. If there are still issues with the draw seek expert advice.
NOTE –The smoke test gives a fair idea on the draw, but is no guarantee that the
products of combustion from the appliance will clear. A spillage test is also required
after the installation.
If spillage occurs after installation contact the manufacturer for advice.
The appliance is designed to be installed into a Class 1 Conventional flue system
that has been lined with a minimum 4” flue liner, or a factory made flue system
conforming to BS 5440-1.
NOTE-The minimum flue liner is 3 meters from the spigot.
The maximum height should be governed by the draw on the individual flue during
the effectiveness of smoke removal/testing of the flue.

19
Conventional Class 1 Chimney (lined only) / Factory made flue system conforming to
BS 5440-1.
Fig.13 Installed into a chimney recess / builders opening.
Flue pipe connection
direct to a flexible
flue liner
Flue system
to terminate
with a flue
terminal
conforming to
BS 5440-1
A flexible liner shall always be used to
line the entire chimney
Flue pipe
sealed to
debris or
register
plate
Dilution air through
integral draught divert
Integral chimney liner
(where built)

20
Fig.14 Free standing installation connected to a factory made flue system.
Flue system to
terminate with
a flue terminal
conforming to
BS 5440-1
The flue system used should
be in accordance with the
appliance manufacturer’s
installation requirements
Dilution air
through integral
draught divert