Chicago Pneumatic CP858 User manual

Operator’s Manual
CP858 Series
Belt Sander
WARNING
To reduce risk of injury, everyone using, installing, repairing, maintaining,
changing accessories on, or working near this tool must read and
understand these instructions, as well as separately provided safety
instructions part number 6159948770, before performing any such task.
CA155539 REV05 04/2015

Fig. 01
Fig. 02
Air Diagram:
L
A
Model
Power Free Speed
Belt
Capacity
LxW
Dimension
LWeight
Air Consumption Air
Inlet
Inner
Hose
Dia.
Sound
Pressure
LpA
Sound
Power
LwA
Vibrations
At load Average ahd K
L
W
H
1 2 3 4 5 6 7 8 9 10 11
[Hp] [W] [rpm] [mm]
[inch] [mm] [inch] [Kg] [lb] [L/min] [SCFM]
[l/min]
[SCFM] [inch] [mm] [inch] [dB(A)] [dB(A)] >PVt@ >PVt@
CP858 0.4 300 18 000 10x330
3/8x13 275 10.8“ 1.13 2 1/2 623 22
311
11 0.25 10 3/8“ 93 104  
Air Supply Diagram 1/2" (12mm)
3/8" (10mm)
3/8" (10mm)
3/8" (10mm)
CA048361 (1/2")
CA048362 (1/2")
CA048360 (1/2")
3/8" (10mm)
3/8" (10mm)
130
90
0
w

1.Technical Data
Model
Power Free speed Belt capacity
LxW
Dimension
LXH :HLJKW
Air Consumption
Air Inlet Inner Hose
Dia.
6RXQGSUHVVXUH
/S$
6RXQGSRZHU
/Z$
9LEUDWLRQV
Average at load DKG K
w
L
W
H
1 2 3 4 5 6 7 8 9 10 11
[Hp] [W] [RPM] >PP@
[inch] [inch] >PP@ >NJ@ >OE@ >OPLQ@
>6&)0@
>OPLQ@
>6&)0@ [inch] [inch] >PP@ >G%$@ >G%$@ >PVt@ >PVt@
max. pressure 6.3bar(90psi)
ah9LEUDWLRQOHYHOk8QFHUWDLQW\LpA6RXQGSUHVVXUHG%$KpA  KWA G%8QFHUWDLQW\
Declaration of noise and vibration statement,62DQG,62
$OOYDOXHVDUHFXUUHQWDVRIWKHGDWHRIWKLVSXEOLFDWLRQ)RUWKHODWHVWLQIRUPDWLRQSOHDVHYLVLWZZZFSFRP
7KHVHGHFODUHGYDOXHVZHUHREWDLQHGE\ODERUDWRU\W\SHWHVWLQJLQDFFRUGDQFHZLWKWKHVWDWHGVWDQGDUGVDQGDUHVXLWDEOHIRUFRPSDULVRQZLWKWKHGHFODUHG
YDOXHVRIRWKHUWRROVWHVWHGLQDFFRUGDQFHZLWKWKHVDPHVWDQGDUGV7KHVHGHFODUHGYDOXHVDUHQRWDGHTXDWHIRUXVHLQULVNDVVHVVPHQWVDQGYDOXHVPHDVXUHG
LQLQGLYLGXDOZRUNSODFHVPD\EHKLJKHU7KHDFWXDOH[SRVXUHYDOXHVDQGULVNRIKDUPH[SHULHQFHGE\DQLQGLYLGXDOXVHUDUHXQLTXHDQGGHSHQGXSRQWKHZD\
WKHXVHUZRUNVWKHZRUNSLHFHDQGWKHZRUNVWDWLRQGHVLJQDVZHOOXSRQWKHH[SRVXUHWLPHDQGWKHSK\VLFDOFRQGLWLRQRIWKHXVHU:H&+,&$*231(80$7,&
722/6  FDQQRW EH KHOG OLDEOH IRU WKH FRQVHTXHQFHV RI XVLQJ WKH GHFODUHG YDOXHV LQVWHDG RI YDOXHV UHᚐHFWLQJ WKH DFWXDO H[SRVXUH LQ DQ LQGLYLGXDO ULVN
DVVHVVPHQWLQDZRUNSODFHVLWXDWLRQRYHUZKLFKZHKDYHQRFRQWURO7KLVWRROPD\FDXVHKDQGDUPYLEUDWLRQV\QGURPHLILWVXVHLVQRWDGHTXDWHO\PDQDJHG
$Q (8 JXLGH WR PDQDJLQJ KDQGDUP YLEUDWLRQ FDQ EH IRXQG DW ZZZ SQHXURSHXXSORDGVGRFXPHQWVSGI3119B'HFODUDWLRQBLQIRBVKHHWBSGI :H
UHFRPPHQGDSURJUDPPHRIKHDOWKVXUYHLOODQFHWRGHWHFWHDUO\V\PSWRPVZKLFKPD\UHODWHWRQRLVHRUYLEUDWLRQH[SRVXUHVRWKDWPDQDJHPHQWSURFHGXUHVFDQ
EHPRGLᚏHGWRKHOSSUHYHQWIXWXUHLPSDLUPHQW
2. Machine type(s)
ವ 7KLVSURGXFWLVGHVLJQHGIRUUHPRYLQJPDWHULDOXVLQJDEUDVLYHV1RRWKHUXVHSHUPLWWHG)RUSURIHVVLRQDOXVHRQO\
ವ 3OHDVHUHDGWKHLQVWUXFWLRQVFDUHIXOO\EHIRUHVWDUWLQJWKHPDFKLQH
3. Operation
• Fix the accessories properly to the tool.
• Connect device as shown in Fig. 01.
• To start the machine, pull the trigger (A). Machine speed is increase by increasing pressure on the trigger. Release the trigger to stop.
• Do not install a quick coupler directly into the sander throttle handle.
4. Lubrification
Use an air line lubricator with SAE #10 oil, adjusted to two drops per minute. If an air line lubricator cannot be used, add air motor oil to the inlet once a day.
Recommended lubricant : CP Oil PROTECTO-LUBE
- 4 oz (0.12l) P/N: CA149661
- 20.8 oz (0.591l) P/N: CA000046
- 1gal (3.8l) P/N: P089507
5. Maintenance instruction
• Follow local country environmental regulations for safe handling and disposal of all components.
ವ 0DLQWHQDQFHDQGUHSDLUZRUNPXVWEHFDUULHGRXWE\TXDOLILHGSHUVRQQHOXVLQJRQO\RULJLQDOVSDUHSDUWV&RQWDFWWKHPDQXIDFWXUHURU\RXUQHDUHVWDXWKRULVHG
GHDOHUIRUDGYLFHRQWHFKQLFDOVHUYLFHRULI\RXUHTXLUHVSDUHSDUWV
ವ $OZD\VHQVXUHWKDWWKHPDFKLQHLVGLVFRQQHFWHGIURPHQHUJ\VRXUFHWRDYRLGDFFLGHQWDORSHUDWLRQ
ವ 'LVDVVHPEOHDQGLQVSHFWWKHWRROHYHU\WKUHHPRQWKVLIWKHWRROLVXVHGHYHU\GD\5HSODFHGDPDJHGRUZRUQSDUWV
ವ +LJKZHDUSDUWVDUHXQGHUOLQHGLQWKHSDUWVOLVW
6. Disposal
ವ 7KHGLVSRVDORIWKLVHTXLSPHQWPXVWIROORZWKHOHJLVODWLRQRIWKHUHVSHFWLYHFRXQWU\
ವ $OOGDPDJHGEDGO\ZRUQRULPSURSHUO\IXQFWLRQLQJGHYLFHV0867%(7$.(12872)23(5$7,21
• Repair only by technical maintenance staff.
7. Declaration of conformity
We : CHICAGO PNEUMATIC Tool Co. LLC 1800 Overview Drive Rock Hill, SC 29730 - USA
Machine type(s): belt sander
Declare that the product(s): CP858 Serial Number: 00000 - 99999A
Origin of the product : JAPAN
is in conformity with the requirements of the council Directives on the approximation of the laws of the Member States relating : to “Machinery“ 2006/42/EC (17/05/2006)
applicable harmonised standard(s) : EN ISO 11148-8:2011
Name and position of issuer :Nicolas Lebreton (R&D Manager)
Place & Date : Saint-Herblain, 04/06/2015
Technical file available from EU headquarter. Nicolas Lebreton R&D manager CP Technocenter 38, rue Bobby Sands - BP10273 44800 Saint Herblain - France
Original Instructions are in English. Other languages are a translation of the original instructions.
Copyright 2015, Chicago Pneumatic Tool Co. LLC
$OOULJKWVUHVHUYHG$Q\XQDXWKRUL]HGXVHRUFRS\LQJRIWKHFRQWHQWVRUSDUWWKHUHRILVSURKLELWHG7KLVDSSOLHVLQSDUWLFXODUWRWUDGHPDUNVPRGHOGHQRPLQDWLRQVSDUWQXPEHUVDQGGUDZLQJV
8VHRQO\DXWKRUL]HGSDUWV$Q\GDPDJHRUPDOIXQFWLRQFDXVHGE\WKHXVHRIXQDXWKRUL]HGSDUWVLVQRWFRYHUHGE\:DUUDQW\RU3URGXFW/LDELOLW\
EN English (English) &36HULHV
EHOWVDQGHU