Chicago Pneumatic CP7263 Series User manual

Operator’s Manual
CP7263, CP7264,
CP7266, CP7267 Series
Random orbital sanders
To reduce risk of injury, everyone using, installing, repairing,
maintaining, changing accessories on, or working near this tool
must read and understand these instructions before performing
any such task.
WARNING

CP7263, CP7264, CP7266, CP7267 Series
Random orbital sander
Original Instructions
Copyright 2011, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the
contents or part thereof is prohibited. This applies in particular to
trademarks, model denominations, part numbers and drawings.
Use only authorized parts. Any damage or malfunction caused
by the use of unauthorized parts is not covered by Warranty or
Product Liability.
Noise & Vibration Declaration*
Sound pressure level 78 dB(A), uncertainty 3 dB(A), in
accordance with EN ISO 15744. For sound power, add 11
dB(A).
Vibration value,
Vibration level a Uncertainty k (m/s²)
CP7263E 9.4 3
CP7263CVE 8.9 2.1
CP7264E 9.2 3.4
CP7264CVE 7.2 2.1
CP7266E 7.3 2.9
CP7266CVE 7.7 2.8
CP7267E 9.6 3.2
CP7267CVE 9 3.7
re. ISO 28927-3.
Declaration of noise and vibration emission
All values are current as of the date of this publication.
These declared values were obtained by laboratory type testing in
accordance with the stated standards and are suitable for comparison
with the declared values of other tools tested in accordance with the
same standards. These declared values are not adequate for use in risk
assessments and values measured in individual work places may be
higher. The actual exposure values and risk of harm experienced by an
individual user are unique and depend upon the way the user works, the
workpiece and the workstation design, as well upon the exposure time
and the physical condition of the user.
We, Chicago Pneumatic, cannot be held liable for the consequences of
using the declared values, instead of values reecting the actual
exposure, in an individual risk assessment in a work place situation over
which we have no control.
This tool may cause hand-arm vibration syndrome if its use is not
adequately managed.
We recommend a programme of health surveillance to detect early
symptoms which may relate to noise or vibration exposure, so that
management procedures can be modied to help prevent future
impairment.
INSTRUCTION MANUAL
Machine Type:
Pneumatic tool equipped with a exible disc tted with
abrasive paper for sanding - No other use is permitted.
Air Supply Requirements
1. Supply tool with 90 psig (6.3 bar) of clean, dry air. Higher
pressure drastically reduces tool life.
2. Connect tool to air line using pipe, hose and tting sizes
shown in the diagram below.
3. Do not install a quick coupler directly into the sander
throttle handle.
Lubrication
Use an air line lubricator with SAE #10 oil, adjusted to two
drops per minute. If an air line lubricator cannot be used,
add air motor oil to the inlet once a day.
Maintenance
1. Disassemble and inspect tool every three months if the tool
is used every day. Replace damaged or worn parts.
2. High wear parts are underlined in the parts list.
3. To keep downtime to a minimum, the following service kits
are recommended: Tune-Up Kit: 8940163459
Technical Data
Pad size:
CP7263 Series: 3”x4-1/4” (75x110mm)
CP7264 Series: 2-3/4”x7-3/4” (70x198mm)
CP7266 Series: 3-1/4”x5” (80x130mm)
CP7267 Series: 3-7/8”-5-5/8” (100x144mm) delta shape
Free speed; 10 000 RPM
Air pressure 90 psi (6.3 bar)
Air comsumption; 18 cfm - 8,5 l/s
Learn more about air sanders and polishers we have.