CHIEF 124 Series User manual

Mercedes Universal
Adapter
Series 124, 129, 140, 170, 202, 208, 210, 220
USERS MANUAL
2006 © Chief Automotive Technologies, Inc.

Chief’s Limited One-Year
Warranty & Liability
CHIEF'S LIMITED ONE-YEAR
WARRANTY & LIABILITY
Chief Automotive Technologies, Inc. warrants for one year from date of installation
and/or purchase any of its products which do not perform satisfactorily due to defect
caused by faulty material or workmanship. Chief’s obligation under this warranty is
limited to the repair or replacement of products which are defective and which have not
been misused, carelessly handled, or defaced by repair or repairs made or attempted by
others.
CHIEF AUTOMOTIVE TECHNOLOGIES, INC. DOES NOT ASSUME
RESPONSIBILITY FOR ANY DEATH, INJURY OR PROPERTY DAMAGE
RESULTING FROM THE OPERATOR’S NEGLIGENCE OR MISUSE OF THIS
PRODUCT OR ITS ATTACHMENTS. CHIEF MAKES NO WRITTEN,
EXPRESS OR IMPLIED WARRANTY WHATSOEVER OF MERCHANTABIL-
ITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE
REGARDING THE EQUIPMENT OR ANY PART OF THE PRODUCT OTHER
THAN THE LIMITED ONE-YEAR WARRANTY STATED ABOVE.

MERCEDES UNIVERSAL ADAPTER
SERIES 124, 129, 140, 170, 202, 208, 210, & 220
519060 Mercedes Universal Adapter Package
1 010632 8 Bolt, 1/2-13NC x 3, Gr. 8
2 019095 8 Washer, 1/2 inch
3 090784 24 Washer, 2 1/2 x 1 3/16 ID x 1/8
4 518171 4 Mercedes Universal Adapter Base
5 532195 8 Spacer, 1/8 inch
6 532196 8 Spacer, 1/4 inch
7 519025 4 Mercedes Pin Plate Adapter Assembly
8 618302 4 Outer Support Pin
9 620736 8 Nut, 1/2-13NC Gr. 8
Ref Part No. Qty. Description
1
8
7
65
4
2
39
*Not included with Mercedes Universal Adapter Package
(Rev. 9/98)
1
Adapter Tube For
Universal Anchoring
System Stand *
UMS Anchoring
Stand *

MERCEDES UNIVERSAL ADAPTER
SERIES 124, 129, 140, 170, 202, 208, 210, & 220
8
7
1
3
9
4
Mercedes 124 Series
2
Application Instructions:
1. Remove conventional clamp jaws.
2. Install pin plate adapter and universal adapter base to the same side of clamp.
3. Install five washers (090784) on adapter base as shown.
4. Insert outer support pin into pin plate adapter.
5. Lower vehicle onto universal adapter base while guiding pins into jack holes.
1 Bolt, 1/2-13NC x 3, Gr. 8
2 Washer, 1/2
3 Washer, 2 1/2 x 13/16 ID x 1/8
4 Mercedes Uni. Adapter Base
5 Spacer, 1/8
6 Spacer, 1/4
7 Mercedes Pin Plate Adapter Ass’y
8 Outer Support Pin
9 Nut, 1/2-13NC, Gr. 8
(refer to part numbers — page 1)
Rev. 6/02
2
1986-1989

MERCEDES UNIVERSAL ADAPTER
SERIES 124, 129, 140, 170, 202, 208, 210, & 220
1
8765
439
2
8
1
765
4
39
2
1 Bolt, 1/2-13NC x 3, Gr. 8
2 Washer, 1/2
3 Washer, 2 1/2 x 13/16 ID x 1/8
4 Mercedes Uni. Adapter Base
5 Spacer, 1/8
6 Spacer, 1/4
7 Mercedes Pin Plate Adapter Ass’y
8 Outer Support Pin
9 Nut, 1/2-13NC, Gr. 8
(refer to part numbers — page 1)
Mercedes Front 129 Series
Mercedes Rear 129 Series
Application Instructions:
1. Remove conventional clamp jaws.
2. Install universal adapter base as shown above.
3. Install pin plate adapter with spacers on opposite side of clamp.
4. Install washers (090784) on adapter base as shown.
5. Insert outer support pin into pin plate adapter.
6. Lower vehicle onto universal adapter base while guiding pins into jack holes.
(Rev. 9/98)
3

MERCEDES UNIVERSAL ADAPTER
SERIES 124, 129, 140, 170, 202, 208, 210, & 220
1 Bolt, 1/2-13NC x 3, Gr. 8
2 Washer, 1/2
3 Washer, 2 1/2 x 13/16 ID x 1/8
4 Mercedes Uni. Adapter Base
5 Spacer, 1/8
6 Spacer, 1/4
7 Mercedes Pin Plate Adapter Ass’y
8 Outer Support Pin
9 Nut, 1/2-13NC, Gr. 8
(refer to part numbers — page 1)
8
1
7
4
39
2
Mercedes 140 Series
Application Instructions:
1. Remove conventional clamp jaws.
2. Install pin plate adapter and universal adapter base on opposite sides of clamp.
3. Install five washers (090784) on adapter base as shown.
4. Insert outer support pin into pin plate adapter.
5. Lower vehicle onto universal adapter base while guiding pins into jack holes.
(Rev. 9/98)
4

MERCEDES UNIVERSAL ADAPTER
SERIES 124, 129, 140, 170, 202, 208, 210, & 220
1 Bolt, 1/2-13NC x 3, Gr. 8
2 Washer, 1/2
3 Washer, 2 1/2 x 13/16 ID x 1/8
4 Mercedes Uni. Adapter Base
5 Spacer, 1/8
6 Spacer, 1/4
7 Mercedes Pin Plate Adapter Ass’y
8 Outer Support Pin
9 Nut, 1/2-13NC, Gr. 8
(refer to part numbers — page 1)
Mercedes Front 170 SLK Series
4
7
8
1
9
2
Application Instructions:
1. Remove conventional clamp jaws.
2. Install pin plate adapter and universal adapter base on opposite sides of clamp.
IMPORTANT: Rocker panel jack tube hole is 20mm higher in the rear and will require three
1/4 inch spacers between stand and pin plate adapter.
3. Insert outer support pin into pin plate adapter.
4. Lower vehicle onto universal adapter base while guiding pins into jack holes.
(Rev. 6/02)
5
1
8
7
4
9
2
6
Mercedes Rear 170 SLK Series

MERCEDES UNIVERSAL ADAPTER
SERIES 124, 129, 140, 170, 202, 208, 210, & 220
1 Bolt, 1/2-13NC x 3, Gr. 8
2 Washer, 1/2
3 Washer, 2 1/2 x 13/16 ID x 1/8
4 Mercedes Uni. Adapter Base
5 Spacer, 1/8
6 Spacer, 1/4
7 Mercedes Pin Plate Adapter Ass’y
8 Outer Support Pin
9 Nut, 1/2-13NC, Gr. 8
(refer to part numbers — page 1)
Mercedes 202 Series
Application Instructions:
1. Remove conventional clamp jaws.
2. Install pin plate adapter and universal adapter base on opposite sides of clamp.
3. Install five washers (090784) on adapter base as shown.
4. Insert outer support pin into pin plate adapter.
5. Lower vehicle onto universal adapter base while guiding pins into jack holes.
(Rev. 9/98)
6
1
8
7
4
39
2

MERCEDES UNIVERSAL ADAPTER
SERIES 124, 129, 140, 170, 202, 208, 210, & 220
1 Bolt, 1/2-13NC x 3, Gr. 8
2 Washer, 1/2
3 Washer, 2 1/2 x 13/16 ID x 1/8
4 Mercedes Uni. Adapter Base
5 Spacer, 1/8
6 Spacer, 1/4
7 Mercedes Pin Plate Adapter Ass’y
8 Outer Support Pin
9 Nut, 1/2-13NC, Gr. 8
(refer to part numbers — page 1)
Mercedes Front CLK 208 Series
Mercedes Rear CLK 208 Series
1
8
7
4
2
39
39
4
2
6
7
8
1(Rev. 9/98)
Application Instructions:
1. Remove conventional clamp jaws.
2. Install pin plate adapter and universal adapter base on opposite sides of clamp.
IMPORTANT: Insert 1/4 inch spacer between pin plate adapter and rear stand.
3. Install five washers (090784) on adapter base as shown.
4. Insert outer support pin into pin plate adapter.
5. Lower vehicle onto universal adapter base while guiding pins into jack holes.
7

MERCEDES UNIVERSAL ADAPTER
SERIES 124, 129, 140, 170, 202, 208, 210, & 220
1 Bolt, 1/2-13NC x 3, Gr. 8
2 Washer, 1/2
3 Washer, 2 1/2 x 13/16 ID x 1/8
4 Mercedes Uni. Adapter Base
5 Spacer, 1/8
6 Spacer, 1/4
7 Mercedes Pin Plate Adapter Ass’y
8 Outer Support Pin
9 Nut, 1/2-13NC, Gr. 8
(refer to part numbers — page 1)
Mercedes 210 Series
1
8
7
6
4
39
2
(Rev. 6/02)
Application Instructions:
1. Remove conventional clamp jaws.
2. Install pin plate adapter and universal adapter base on opposite sides of clamp.
IMPORTANT: Insert 1/4 inch spacer between pin plate adapter and stand.
3. Install five washers (090784) on adapter base as shown.
4. Insert outer support pin into pin plate adapter.
5. Lower vehicle onto universal adapter base while guiding pins into jack holes.
8