CHIEF PSM-2230 User manual

INSTALLATION INSTRUCTIONS
CHIEF MANUFACTURING INC.
1-800-582-6480 952-894-6280 FAX [phone] Chief Manufacturing
12800 HIGHWAY 13 SOUTH, SUITE 500 www.chiefmfg.com
SAVAGE, MINNESOTA 55378 USA 01/03
PLASMA DISPLAY STATIC MOUNT
PSM-2230, PSM-2231 & PSM-2232
(1) Bracket, Plasma Mounting, Static (1) 10-24 x .5 FH Undercut Screw
(1) Latching Flag (1) 10-24 Nylock Nut
(6) Mounting Buttons, Steel, Silver (6) M6 x 25mm Phillips Head Cap Screws
(1) Nylon Washer .250" OD x .1875" ID x .0312" (6) M6 x 30mm Button Head Cap Screws
(6) Nylon Spacer, .750 x .250ID x .25” (4) Rubber Bumpers
(1) M4 Allen Key
NOTE: Not all parts are used for every application.
BEFORE PROCEEDING: Unpack the carton, verify contents shown in Figure 1 and read
installation instructions completely. If you are missing any of the listed components, please
contact Customer Service at 1-800/582-6480.
PLASMA DISPLAYS ARE EXTREMELY FRAGILE.
CAUTION!
Figure 1

PSM 2230
42” 4:3 Aspect Ratio Plasma
1. Attach six Nylon spacers and mounting buttons to plasma using six M6 x 30mm button head
screws provided (see Figure 2 ).
2. Secure latching flag to Plasma Static Mount using .250" OD x .03125" ID x .0312" Nylon
Washer, 10-24 x .5 FH Undercut Screw, and 10-24 Nylock Nut (see Figure 3).
3. Install four rubber bumpers as shown in Figure 4.
ALL COMPONENTS MUST BE SECURELY FASTENED
TO A STRUCTURAL MEMBER CAPABLE OF
SUPPORTING 4 TIMES THE COMBINED WEIGHT OF
ALL COMPONENTS PLUS THE EQUIPMENT BEING
MOUNTED. IF IT CANNOT SUPPORT THIS WEIGHT,
THE STRUCTURE MUST BE REINFORCED.
THE MAXIMUM WEIGHT TO BE INSTALLED ON THE
MOUNT IS 150 POUNDS (68.04 KG).
4. Securely anchor the plasma static mount to the wall using wall studs or supporting
framework (see WARNING).
5. Make sure the flag is lowered to the side before attempting to place the plasma on the mount.
6.
With the aid of another person, lift the plasma display up to the mount, align the mounting buttons on
the plasma with the teardrop slots in the mount, and set the plasma into place (see Figure 5).
7. Position (raise) the flag to secure the plasma.
This side toward
display
Rubber Bumpers
Align Mounting
Buttons with
Teardrop Slots
This side
toward wall
Anchor to wall
using four slots
N
OTE: Mount shown
light color for better viewing
Figure 4 Figure 5
Figure 2
N
ylon Space
r
Mounting Button
M6 x 30mm Cap Screw
Here
Figure 3
10-24 Nylock Nut
installed from
underside
Latching Flag
N
ylon Washer
between flag & mount
10-24 x .5 FH
Undercut Screw
WARNNG!

PSM 2231
46” Plasma
1. Attach six mounting buttons to plasma using six M6 x 25mm Phillips head screws
provided (see Figure 6 ).
2. Secure latching flag to Plasma Static Mount using .250" OD x .1875" ID x .0312" Nylon
Washer, 10-24 x .5 FH Undercut Screw, and 10-24 Nylock Nut (See Figure 7).
3. Install four rubber bumpers as shown in Figure 8.
ALL COMPONENTS MUST BE SECURELY FASTENED
TO A STRUCTURAL MEMBER CAPABLE OF
SUPPORTING 4 TIMES THE COMBINED WEIGHT OF
ALL COMPONENTS PLUS THE EQUIPMENT BEING
MOUNTED. IF IT CANNOT SUPPORT THIS WEIGHT,
THE STRUCTURE MUST BE REINFORCED.
THE MAXIMUM WEIGHT TO BE INSTALLED ON THE
MOUNT IS 150 POUNDS (68.04 KG).
4.
Securely anchor the plasma static mount to the wall using wall studs or supporting framework.
5. Make sure the flag is lowered to the side before attempting to place the plasma on the mount.
6.
With the aid of another person, lift the plasma display up to the mount, align the mounting buttons on
the plasma with the teardrop slots in the mount, and set the plasma into place (see figure 9).
7. Position (raise) the flag
to secure the plasma.
Mounting Button
M6 X 25mm Phillips Screw
Here
Align Mounting
Buttons with
Teardrop Slots
Anchor to wall
using four slots
Figure 6
Figure 9
Figure 7
10-24 Nylock Nut
installed from
Latching Flag
(Note outer
hole location
)
N
ot here
N
ylon Washer
b
etween fla
g
& moun
t
10-24 x .5 FH
Undercut Screw
Figure 8
Install Rubber
Bumpers
WARNNG!

PSM 2232
42” 16:9 Aspect Ratio Plasma
1. Attach six mounting buttons to plasma using six M6 x 25mm Phillips head screws provided
(see Figure 10 ).
2. Secure latching flag to Plasma Static Mount using .250" OD x .1875" ID x .0312" Nylon
Washer, 10-24 x .5 FH Undercut Screw, and 10-24 Nylock Nut (See Figure 11).
ALL COMPONENTS MUST BE SECURELY FASTENED
TO A STRUCTURAL MEMBER CAPABLE OF
SUPPORTING 4 TIMES THE COMBINED WEIGHT OF
ALL COMPONENTS PLUS THE EQUIPMENT BEING
MOUNTED. IF IT CANNOT SUPPORT THIS WEIGHT,
THE STRUCTURE MUST BE REINFORCED.
THE MAXIMUM WEIGHT TO BE INSTALLED ON THE
MOUNT IS 150 POUNDS (68.04 KG).
3. Securely anchor the plasma static mount to the wall using wall studs or supporting framework.
4. Install four rubber bumpers as shown in Figure 12.
5. Make sure the flag is lowered to the side before attempting to place the plasma on the mount.
6. With the aid of another person, lift the plasma display up to the mount, align the mounting buttons on
the plasma with the teardrop slots in the mount, and set the plasma into place (see Figure 13).
7. Position (raise) the flag to secure the plasma.
Figure 10 Figure 11
Latching Flag
(Note inner
hole location
)
10-24 x .5 FH
Undercut Screw
N
ylon Washer
between flag &
mount
10-24 N
y
lock Nut installed
from underside
Mounting Buttons
Here
Anchor to wall
using four slots
Align Mounting
Buttons with
Teardrop Slots
Figure 13
Install Rubber
Bumpers
Figure 12
WARNNG!